PR Lighting DESIGN 150 Bedienungsanleitung

DESIGN 150

PR-1150

This product manual contains important information about the safe installation and

use of this projector. Please read and follow these instructions carefully and keep this

manual in a safe place for future reference.

PR LIGHTING LTD

571 Yingbin Road Dashi Panyu Guangzhou 511430, China

http://www.pr-lighting.com

INDEX

SAFE USAGE OF THE PROJECTOR 3

INSTALLING THE PROJECTOR 4

FITTING THE LAMP 4

POWER CONNECTIONS 5

CONTROL CONNECTIONS 5

DMX TERMINATOR 6

DMX CONTROL CHANNEL FUNCTIONS 6

TO SET THE DMX START ADDRESS 6

SETUP OPTIONS 7

SETUP OPTIONS TABLE 7

STAND-ALONE MODE 8

MAINTENANCE 8

KEEPING THE PROJECTOR CLEAN 8

TROUBLESHOOTINGS 8

TECHNICAL DATA 9

LIGHT OUTPUT 10

ELECTRICAL DIAGRAM 10

COMPONENT ORDER CODES 11

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change

without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the

course of product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any

consequence arising from them.

Every apparatus is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the

apparatus is in good condition before your installation and use. Should there be any damage caused by transportation, consult

your dealer and do not use the apparatus. But any damage caused by improper use will not be assumed by the manufacturer

and / or dealer.

ACCESSORIES

THESE ITEMS ARE PACKED TOGETHER WITH THE PROJECTOR

Water proof 3-pin XLR plug (1 PCS)

Water proof 3-pin XLR socket (1 PCS)

Safety cord (1 PCS)

Barndoors (1 SET) (including 4 copper screws and 4 rubber washers, 4 screws and 4 flat washers)

This manual (1 PCS)

Optional: louvres (1 SET)

INTRODUCTION

Thank you for purchasing our product Design 150, PR-1150.

This product manual contains important information about the safe installation and use of this

projector. Please read and follow these instructions carefully and keep this manual in a safe place for

future reference.

The Design 150 is a projector of innovative, compact, silent colour changing, capable of extraordinary

perforamances in terms of colour mixing, reliability and versatility. The projector can be used in

numerous environments and for the most various applications. The product complies to CE norms and

standards and uses international protocol DMX 512. Design 150 can be used as a stand-alone unit or

linked to a controller. The Design 150 are particularly suitable for television studios and theatres, stage

lighting, limelights, backdrops, inside or outside shops and shopping centres, sport and other cultural

applications, and so on.

The Design 150 features 3 kinds of colour filters for CYM colour mixing and 2 blads for shutter/open. It

can be setup easily with the touch-switches and a digital display screen.

Design 150 manual.doc

2/12

SAFE USAGE OF THE PROJECTOR

When unpacking and before disposing of the carton check there is no transportation damage before

using the projector. Keep the carton well for future possible transportation. Should there be any

damage caused by transportation, consult your dealer and do not use the apparatus.

The projector is suitable for indoor or outdoor use and is splash-proofed, IP65.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Do not project the beam onto inflammable surfaces, minimum distance is 3m. 3m

Hot housing surface! Do not touch the housing of the projector with your hand during operation.

Avoid direct exposure to the light from the lamp. The light is harmful to the eye.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power

requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all

relevant standards.

Do not connect this device to any dimmer pack.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-

cord come into contact with other cables. Only handle the power-cord by the plug. Never pull out the

plug by tugging the power-cord.

Keep the lamp clean. Do not touch the lamp glass with bare hand.

The projector should always be installed with a secondary safety fixing. A safety cord is supplied for

this, it should be attached as shown in “installing the projector” section.

The lamp used in this projector is an 150W discharge lamp. After being switched off don’t attempt to

restart the projector until lamp has cooled, this will require approx 15 minutes. Switching the lamp on

and off at short intervals will reduce the life of both the lamp and the projector. But occasional breaks

will prolong the life of the lamp and projector.

Never run the projector without a lamp.

There are no user serviceable parts inside the projector, do not open the housing and never operate

the projector with the covers removed.

Always disconnect from the mains, when the device is not in use or before cleaning it or

before attempting any maintenance work.

NOTE: PLEASE REMOVE THE SPONGE EFFECT LOCKING CYLINDER INSIDE THE

PROJECTOR BEFORE YOUR FIRST OPERATION!

(How to open the access cover please refer to “fitting the lamp” section)

Design 150 manual.doc

3/12

INSTALLING THE PROJECTOR

The unit was designed to make installation easy: it can be fitted on a floor, wall or ceiling as required

and will operate in any working position, as the head can be rotated through 90°.

Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning.

Always ensure that the structure to which you are attaching the projector is secure and is able to

support a weight of 17.6Kg for each Design 150. For safety the projector should have a secondary

fixing with a safety chain through the 2 secondary safety yokes on the both sides of the unit.

Note: For installing the barndoors, first install the 4 copper screws and sealing rubber washers in the

unit head, and then place the barndoors on the 4 copper screws and fasten them with 4 screws and

flat washes.

FITTING THE LAMP

Loosen the 2 M6 screws and then open the head cover as shown in the figure above.

Appear the lamp holder by letting the colour filters and blades aside from the center.

Plug the lamp into the lamp holder. Note: To avoid premature lamp failure, do not touch the lamp

glass with your fingers. If you touch the lamp during installation, clean it carefully with rubbing alcohol

and a clean, lint-free cloth before operation.

Close the cover and then tighen the 2 M6 screws.

NOTE: The HSD series are high pressure lamps with external igniters ( ). Care should always be

taken when handling these lamps. Always read the manufacturers "Instructions for use" enclosed with

the lamp. Design 150 manual.doc

4/12

POWER CONNECTIONS

The unit is supplied with a power cord. Should any other connections be required they must be carried

out with the following configuration.

Earth = Green/Yellow cord

Neutral = Blue cord

Live = Brown cord

CONTROL CONNECTIONS

Connection between controller and projector and between one projector and another must be made

with 2 core screened cable, with each core having at least a 0.5mm diameter. Connection to and from

the projector is via cannon 3 pin XLR plugs and sockets which are included with the projector. The

XLR's are connected as shown in the figure above.

Note, care should be taken to ensure that none of the connections touch the body of the plug or each

other. The body of the plug is not connected in any way. The Design 150 accepts digital control

signals in standard DMX512 (1990) format.

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the

second fixture’s input. The rest may be deduced by analogy. Eventually connect the last fixture’s

output to a DMX terminator as shown in the figure below

Design 150 uses 3-pin XLR plug / socket. If your controller uses 5-pin XLR plug / socket, you should

convert 5-pin plug / socket into 3-pin socket / plug as shown below.

Design 150 manual.doc

5/12

DMX TERMINATOR

In the Controller mode, the DMX output has to be connected with a DMX terminator at the last fixture

in the chain. This prevents electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2

and 3, which is then plugged into the output socket on the last projector in the chain. The connections

are illustrated below.

DMX TERMINATOR CONNECTION

Connect a 120Ω(OHM) resistor across

pins 2 and 3 in an XLR plug and insert

into the DMX OUT socket on the last

unit in the chain.

DMX CONTROL CHANNEL FUNCTIONS

The Design 150 uses 6 DMX channels. They are listed in the following table.

CHANNEL DMX VALUE DESCRIPTION

1 0-255 From black to full open in linear

0-1 Open/Clear

2 2-255 Mix CYM colours from slow to fast

3 0-255 Cyan enters gradually

4 0-255 Magenta enters gradually

5 0-255 Yellow enters gradually

6 0-255 Control motor speeds of cyan, yellow and magenta from fast to

slow

PROJECTOR DMX START ADDRESS

Each Design 150 must be given a DMX start address so that the correct projector responds to the

correct control signals. This DMX start address is the channel number from which the projector starts

to “listen” to the digital control information being sent out from the controller. The Design 150 has 6

channels, so set the No.1 projector’s address 001, No.2 projector’s address 007, No.3 projector’s

address 013, No.4 projector’s address 019, and so on.

TO SET THE DMX START ADDRESS

Press UP or DOWN button to select (address setting), and then press ENTER button. You

will see the flashing, then press UP or DOWN button to get the desired address value. At last,

press ENTER button to save and then press FUNC button to come back (address setting).

Design 150 manual.doc

6/12

SETUP OPTIONS - PROJECTOR CONFIGURATION

After the projector is switched on, the projector will reset automatically and then the display will show

the DMX start address (if you have already set the DMX start address and saved it, the screen will

display the last setting).

To set or browse through the various Setup Options, press the UP or DOWN button.

Press ENTER button to save your modification or enter sub-option. Press the UP or DOWN button to

modificate the setting values.

Press FUNC button to exit current option and to return to pre-option.

For example, if you want to set digit display brightness 100%, you should press UP or DOWN button

to select (digit display brightness). Press ENTER button to enter value setting (sub-option),

press UP or DOWN button to get (100%), then press ENTER button to save and press

FUNC button to return to . So you successfully set the digit display brightness 100%.

SETUP OPTIONS TABLE

Design 150 manual.doc

7/12

STAND-ALONE MODE

Press the UP or DOWN button to select (self test), and then press ENTER button to confirm

it. The projector will run in stand-alone mode automatically under programmes have been set.

MAINTENANCE

If the projector’s lens becomes damaged or broken it should be replaced. If the lamp becomes

damaged or deformed in any way it must be replaced. If the light from the lamp appears dim this would

normally indicate that it is reaching the end of its life and it should be changed at once, old lamps run

to the extremity of their life can explode. If the projector does not function, check the power fuse inside

the projector, it should only be replaced by fuse with the same specified value 6.3A/250V (fast blow,

5mmx20mm). On the main PCB inside the projector there is also 2 fuses rated 6.3A/250V and

4A/250V (fast blow, 5mmx20mm) respectively. When change the fuses, please undo the 4 M6

screws on the base of the projector and then open the base cover. Should these be damaged call

a qualified technician before replacement. The projector has thermal protection device that will switch

off the projector in case of overheating.

Any maintenance work should only be carried out by qualified technicians.

KEEPING THE PROJECTOR CLEAN

To ensure the reliability of the projector it should be kept clean. The lens and dichroic colour filters

should also be regularly cleaned to maintain an optimum light output. Do NOT use any type of

solvent on dichroic colour filters.

Cleaning frequency depends on the environment in which the fixture operates: damp, smoke or

particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics. A soft cloth

and typical glass cleaning products should be used in cleaning. It is recommended to clean the

external optics at least once every 20 days and clean the internal optics at least once every 30 / 60

days.

Do not use any organic solvent, e.g. alcohol, to clean the reflector, colour

filters or housing of the apparatus.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE ACTION

The projector doesn’t switch

on -The power supply is not

present

-The lamp is not working

Check the fuse on the power socket.

Replace the lamp.

The lamp comes on but the

projector doesn’t respond to

the controller

-Wrong DMX configuration

and/or start address

- Defective DMX cable

Make sure that the projector is

correctly configurated.

Replace or repair the DMX cable.

The beam appears dim -Dust or grease contamination

on the optics.

-The lamp is at the end of its

life

Check the optics are clean.

Replace with a new lamp of the

specified type and rating.

Design 150 manual.doc

8/12

TECHNICAL DATA

VOLTAGES: 100/120/200/220/230/240V AC, 50Hz or 60Hz To Order.

POWER CONSUMPTION:

200W@220V

LAMP: Type : HSD150/70 discharge lamp.

Colour Temperature: 7000ºK

Socket:G12

Manufacturers Rated Lamp Life: 2000 Hours

COLOURS:

CYMcolourmixing

With crossfade effect at various speeds

SHUTTER:

2 Blades for shutter

HEAD MOVEMENT:

90º (manual adjustment)

BEAM ANGLE:

21º

CONTROL:

DMX512: 6 Channels

Stand-Alone Automatic mode

Lamp and Unit time indication

MOTORS:

8 Stepper motors

HOUSING:

Cast aluminium with paint finish (IP65)

WEIGHT:

17.6Kg.

Design 150 manual.doc

9/12

LIGHT OUTPUT

Design 150 manual.doc

10/12

ELECTRICAL DIAGRAM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PR Lighting Beleuchtungsausrüstung Handbücher

PR Lighting

PR Lighting CUBIX300 Bedienungsanleitung

PR Lighting

PR Lighting ARC LED 372 Bedienungsanleitung

PR Lighting

PR Lighting PR-6000 FRAMING Bedienungsanleitung

PR Lighting

PR Lighting XR250 Bedienungsanleitung

PR Lighting

PR Lighting XL WASH 700 Bedienungsanleitung

PR Lighting

PR Lighting CHAMELEON PR-2012H Bedienungsanleitung

PR Lighting

PR Lighting TANGO FRAMING Bedienungsanleitung

PR Lighting

PR Lighting XR130 Beam Bedienungsanleitung

PR Lighting

PR Lighting PR-8120 Bedienungsanleitung

PR Lighting

PR Lighting AQUA 580 BWS Bedienungsanleitung

PR Lighting

PR Lighting LS150 TREE Bedienungsanleitung

PR Lighting

PR Lighting PR-8170A Bedienungsanleitung

PR Lighting

PR Lighting AQUA 380 BWS Bedienungsanleitung

PR Lighting

PR Lighting AQUA LED 3000-W FRAMING Bedienungsanleitung

PR Lighting

PR Lighting PR-2001L Bedienungsanleitung

PR Lighting

PR Lighting AQUA LED 1500 SPOT Bedienungsanleitung

PR Lighting

PR Lighting AQUA 380 BEAM Bedienungsanleitung

PR Lighting

PR Lighting Junior JNR-8142D Bedienungsanleitung

PR Lighting

PR Lighting XLED 4007 BEAM Bedienungsanleitung

PR Lighting

PR Lighting PR-111ER MOON Bedienungsanleitung

PR Lighting

PR Lighting XLED 590 Bedienungsanleitung

PR Lighting

PR Lighting PR-2330 Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Bedienungsanleitung

PR Lighting

PR Lighting PR-2900 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung