PR Lighting XLED 4007 BEAM Bedienungsanleitung

XLED 4007 BEAM

PR-8126

This product manual contains important information about the safe installation and use of this product. Please

read and follow these instructions carefully before installing and using the product and keep this manual in a

safe place for future reference.

PR LIGHTING LT .

http://www.pr-lighting.com

INDEX

SAFETY AN WARNINGS

INSTUCTIONS

●

CLEANING AN MAINTENANCE

●

TROUBLESHOOTING

3. APPEARANCE

4. INSTALLATION

●

RIGGING

●

POWER CONNECTIONS

●

MX CONTROL CONNECTION

●

MX TERMINATOR

5. SETUP AN CONFIGURATION

●

FRONT PANEL OPERATION

●

MX START A RESS

●

MX WIRELSESS CONTROL

●

STAN -ALONE MO E

●

MASTER/SLAVE MO E

●

SOUN OPERATION

6.OPERATION MENU

7. MX PROTOCOL

8. LE IN ICATION

TECHNICAL ATA

10.CIRCUIT IAGRAM AN PCB CONNECTIONS

●

CIRCUIT IAGRAM

●

PCB CONNECTIONS

11.COMPONENT OR ER CO ES

ACCESSORIES

The following items are supplied with the projector and please check:

Name Quantity Unit Remark

XLR Cable 1 Pc With plug and socket

Safety cord 1 Pc

User Manual 1 Pc

Ω Clamp

1 Pc (Optional)

G Clamp

1 Pc Standard

Wireless Receiver Accessory 1 Pc Standard

Please note that as art of our ongoing commitment to continuous roduct develo ment, s ecifications are subject to

change without notice. Whilst every care is taken in the re aration of the manual we reserve the right to change

s ecifications in the course of roduct im rovement. The ublishers cannot be held res onsible for the accuracy of the

information herein, or any consequence arising from them.

Every unit is tested com letely and acked ro erly by the manufacturer. Please make sure the acking and / or the unit

are in good condition before installation and use. Should there be any damage caused by trans ortation, consult your

dealer and do not use the unit. Any damage caused by im ro er use will not be assumed by the manufacturer and / or

dealer.

Note: For the roducts made by Guangzhou PR lighting Ltd, the warranty for the whole roduct is one year starting from the delivery date

but the light source is not within the warranty.

1. SAFETY AND WARNINGS

NOTE

Before a rojector’s installation, ower-on, o eration and maintenance, lease carefully read

the safety information hereinafter!

The following safety signs are used in the user manual.

Warning

User

Manual

Electrical

shock

Goggles

Protective

Gloves

Flames

High

Tem erature

●

When un acking , check if there is trans ortation damage before using the rojector. Should there be any

damage caused by trans ortation, consult your dealer and do not use it.

●

The manufacture is not responsible for loss caused by the user not following the manual or changing the projector

as he/she likes

●

Please be noted that the damage caused by changing the projector at will is not warranted.

●

o not hesitate to contact the dealer or the manufacturer if any questions or advice.

●

The projector is for indoor use only, IP20.

●

Use only in dry locations. Keep this unit away from rain and moisture, excessive heat, humidity and dust. o not

allow contact with water or any other liquids.

●

The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while

being operated

●

The projector is only intended for installation, operation and maintenance by qualified personnel. And the

operation must strictly follow the procedures in the manual

●

No repairable parts in the projector and do not open covers for maintenance by yourself.

●

on’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned.

●

o not connect this device to any type of dimmer pack

●

After lamp switched on, the minimum distance between the projector and illuminated surface is 10m

●

lens and other optical parts shall be replaced immediately if they have deformed or been damaged, otherwise the

light output will be compromised.

●

Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use a

projector while covers(housing)are off

●

Keep the lamp clean and do not touch it with bare hands.

●

While operating it, wear protective items.

●

Any electrical connection must be carried out by a qualified person .

●

Before installation, please confirm the voltage supplied matches what is required for the projector

●

Each projector must be properly earthed and installed as per related electrical standards.

●

o not use power cord with its insulator damaged and connect the power cord with other cables.

●

If the projector is not used or under cleaning,, please hold the plug and unplug it. o not unplug it forcefully

or by pulling the power cable.

●

All power cords must conform to related safety and regulations

●

While being operated, the projector should not be under rains or in humidity.

●

o not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other

electrical parts’ life will be shortened .

●

There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety

n the projector and illuminated surface is 1.5m

cord supplied through the safety cord holes for safety support.

●

Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from

power mains.

●

After running for 30minutes, the temperature of the housing of the projector is

.After stable operation ,

℃

its temperature is

℃

●

While the lamp is stricken for the first time, there will be smoke and strange smell. It’s normal and does not

mean the projector has some defects.

●

o not mount the projector directly on inflammable surface.

●

o not project the beam straightly on combustible items and the minimum distance between the

projector and illuminated items is 10m.

●

A projector should be installed with good ventilation and the minimum distance between the projector

and walls is 50cm. At the same time, please ensure the fans and air inlets and outlets are workable.

INSTRUCTIONS

●

CLEANING AND MAINTENANCE

If a projector can’t start. Please check if the fuse is blown up. If it does, replace it with a new fuse with same ratings. And the

projector has over-temperature protective device. If the temperature is too high, the protective device will be triggered to shut the

projector off. When it happens, please check if the fans run normally or fan shield is blocked by dust. After the issue is solved,

restart the projector.

The accumulation of oil, smoke and dust on the lens will compromise the light output. Cleaning a projector is very necessary to

ensure a reliable use of it. Cooling fans need to be cleaned every 15days. Internal lens, reflector and hot mirror need to be cleaned

periodically to optimize light output.

Cleaning frequency is to be decided by operations and its environment. Use soft cloth and normal detergent for glass for cleaning

work. It’s advised external optical system be cleaned every 20days and internal optical systems every 30/60days. Keep lens clean

and do not touch optical parts with bare hands.

●

Before any maintenance and cleaning, please ensure the project is off the power

●

Only qualified person is allowed to do maintenance

●

uring maintenance and before maintenance, the projector must be off power.

●

To avoid internal damage, sun light or other light mustn’t penetrate into the projector via

front lens whether it runs or not

●

o not use alcohol or other organic solvent to clean the housing to avoid damage.

●

o not use any solvent with chemical elements to clean color filters or hot mirror.

●

TROUBLESHOOTING

PROBLEM ACTION

The projector doesn’t switch on  Check the fuse on the power socket.

 Check the lamp.

The lamp is on but the projector doesn’t respond

to the controller

 Make sure that the fixture’s start address is right

 Replace or repair the XLR signal cable.

The projector functions intermittently  Make sure the fan is working well or fans and their shields are not blocked

Beam appears dim, Low in brightness  Make sure the lamp is within its lifespan

 Remove dust or grease from the lenses.

The project image appears to have a halo  Carefully clean the lamp, optical lenses and other components.

Heavily efective Beam  Check if lens are in good condition(not cracked)

 Clean dust or grease on the lens.

3. APPEARANCE

No. Name Remark

1 Head

2 Yoke

3 Base

4 Control Panel

5 Power Cable

Wireless Antenna

Transparent Waterproof Panel installed of the accessory package

If used underwater or in dusty or other harsh areas.

4. INSTALLATION

●

RIGGING

Take 1 clamp and 1 the safety cord out from the package and mount 1 clamp on the BOTTOM of fixture with 2 retainers attached to

the clamp. Hang the fixture on the steel truss and fasten the retainers attached to the clamp. Always ensure that the location that you are

going to mount the unit is secure and is strong enough to support the weight of the unit (See the WARNING as shown above) To ass

SAFETY CORD through the SAFETY HOLE on the back cover of the base of the fixture for safety! Always ensure that the

unit is firmly anchored to avoid vibration and slipping whilst functioning.

WARNING:

●

The projector MUST be lifted or carried by the HAN LES instead of clamps.

●

.For safety the safety cord should afford 10 times the Projector’s weight.

●

POWER CONNECTION

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended that each

projector be connected with power separately so that they may be individually switched on and off.

Note: If projectors are connected in series, please connect POWERIN port of the 1

projector with the Power Mains, then

connect its POWER OUT with POWER IN of the 2

projector, and so on till all fixtures are connected. If the voltage supplied

is 200V-240V, the maximum projectors connected is 8pcs, if it is 100V-120V, the maximum is 4pcs. The diameter of the cores

of the wires for the Power in/out cables must be equal or bigger than

2.5mm

2 .

●

The earth wire(yellow/green) must be connected to the ground. And electrical connection must be in

accordance with the standards concerned.

●

If any questions about the electrical installation, do not continue but consult a qualified electrician.

●

DMX CONTROL CONNECTION

Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with

each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the

projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown in the figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets

mustn’t be connected in any way other than mentioned in the above figure. The projector accepts digital control signals in protocol

MX512 (1990).

Connect the controller’s MX output to the first fixture’s MX input, and connect the first fixture’s MX output to the second

fixture’s MX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s MX output to a MX

terminator as shown in the figure below.

●

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the MX output has to be connected with a MX terminator. This prevents

electrical noise from disturbing and corrupting the MX control signals.

The MX terminator is simply an XLR connector with a 120Ω (ohm) resistor connected across pins 2 and 3, which is then plugged

into the output socket on the last projector in the chain. The connections are illustrated below.

5. SETUP AND CONFIGURATION

●

Front Panel Operation

Control panel with wireless function:

Control panel without wireless function:

Fixture’s address and function code configuration can be set conveniently via Touch Key and LC display. Press button ENTER

more than 3 seconds to unlock panel. LE display shows the fixture’s function menu. Each Option of the main menu has its own

sub-menu. Each menu stands for specified function of the fixture, please see the details in the following:

Press button UP or OWN if you want to set or browse through the various Setup Options.

120

DMX TERMINATOR

CONNECTION

Connect a 120 (O M) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

Press button ENTER to save your settings or enter the sub-menus.

Press button UP or OWN to change the parameters (increase or decrease the numbers)

Press button FUNC, it will return to the upper menu one by one. If the button not pressed, the system will go back to display status

automatically.

●

DMX START ADDRESS

If many fixtures are controlled by the controller, each fixture should be set with a start address to receive signals sent by the controller

and respond to it. The fixture have 2 MX modes. There are standard mode and extended mode, For example standard mode has 18

channels, so set the No. 1 Fixture’s address 001, No. 2 Fixture’s address 019, No. 3 Fixture’s address 037 and so on.

Switch on the Fixture. Press button ENTER more than 2 seconds to unlock panel.

Press either buttons of UP and OWN, under 1st level menu to locate the menu of MX A RESS, press ENTER to set MX

address.

Press button UP and OWN, you can set the address;

Press button ENTER to confirm; when powered on next time, it will show the latest number you saved.

Press button FUNC, it will return to the upper menu one by one.

●

DMX WIRELESS CONTROL (If the projector has the function)

The projector has wireless control function with wireless receiver module and antenna for remote control.

The setup of it is below:

Enter into the projector’s menu. Select the menu “Config Settigns” via the bottoms of

UP and OWN

Select DMX control Mode---- Wireless First (Note: do not select XLR ONLY),then wireless indication in the

front panel will be on, meaning wireless control function is activated.

Only after the projector is linked with a transmitter, can it receive wireless signal sent by the transmitter. If unlinking it,

Press “Enter” for the menu of Unlink Wireless under the upper level menu of Config Settigns .

●

STAND-ALONE MODE

Operate the projector without connecting with a controller, enable the master mode through the operation panel, the

projector will run in Stand-Alone mode automatically.

MX address can be set at any number within 512.

●

MASTER/SLAVE MODE

Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,

connect the first fixture’s MX output to the second fixture’s MX input using XLR-XLR control cable and then connect the second

fixture’s MX output to the third fixture’s MX input, and so on until all projector are connected in this way. Eventually connect the

last fixture’s MX output to a MX terminator. Set 1

projector as the master and others are Slaves.

Start Addresses of all Slaves are 001; Operation mode of the Master can be set any mode for a Master’ and Slaves’ operation mode can

be set accordingly.

After Powered on, the group will run in Master/Slave Mode

●

Sound O eration

To select different level(1-100) of sound sensitivity based on different operating environment under sound operation under

Operation Mode. There are several different(0-8) sound effects for different operating environment under Sound

Operation.

Note: If several fixtures in series under Master/Slave mode, Only Master responds to external sound.

6. OPERATION MENU

level menu 2

level menu 3

level menu 4

level menu

MX Address

Standard 1~495

Extended 1~470

Reset Are You Sure

Config Set

MX Mode

（

efault is

：

Standard 18

）

Standard 18

Extended 43

Loss of MX

( efault: Normal Time Out)

Normal Time Out

Hold Last Value

Wireless Mode

( efault: XLR First)

XLR First

XLR Only

Wireless Only

Wireless First

Wireless to XLR

Master/Slave

( efault: Slave)

Slave

Master

isplay Mode

( efault: off After elay)

Off After elay

On Always

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PR Lighting Beleuchtungsausrüstung Handbücher

PR Lighting

PR Lighting AQUA 350 BEAM Bedienungsanleitung

PR Lighting

PR Lighting ARC LED 372 Bedienungsanleitung

PR Lighting

PR Lighting PR-2900 Bedienungsanleitung

PR Lighting

PR Lighting PR-8836 Bedienungsanleitung

PR Lighting

PR Lighting AQUA 580 BWS Bedienungsanleitung

PR Lighting

PR Lighting XL 1500 Bedienungsanleitung

PR Lighting

PR Lighting XL 1500 Bedienungsanleitung

PR Lighting

PR Lighting PR-2330 Bedienungsanleitung

PR Lighting

PR Lighting XR250 Bedienungsanleitung

PR Lighting

PR Lighting XPar 150 Zoom Bedienungsanleitung

PR Lighting

PR Lighting Junior JNR-8142D Bedienungsanleitung

PR Lighting

PR Lighting PR-8920 Bedienungsanleitung

PR Lighting

PR Lighting XR130 Beam Bedienungsanleitung

PR Lighting

PR Lighting Mega Colour 2500 Bedienungsanleitung

PR Lighting

PR Lighting CENTURY SPOT PR-2002 Bedienungsanleitung

PR Lighting

PR Lighting PR-8846 Bedienungsanleitung

PR Lighting

PR Lighting PR-8121 Bedienungsanleitung

PR Lighting

PR Lighting CUBIX300 Bedienungsanleitung

PR Lighting

PR Lighting PR-2001L Bedienungsanleitung

PR Lighting

PR Lighting PR-8835 Bedienungsanleitung

PR Lighting

PR Lighting XR 380 BWS Bedienungsanleitung

PR Lighting

PR Lighting XR 1400 Framing Bedienungsanleitung

PR Lighting

PR Lighting DESIGN 150 Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung