PR Lighting ARC LED 372 Bedienungsanleitung

ARC LED 372

PR-8805

The user manual contains important information about the safe installation and use of a projector. Please read

andfollowthese instructions carefullyandkeepthemanual in asafeplaceforfuturereference.

PR LIGHTING LTD.

http://www.pr-lighting.com

INDEX

1. SAFETYANDWARNINGS

2. INSTUCTIONS

●CLEANINGANDMAINTENANCE

●TROUBLESHOOTING

3.APPEARANCE

4.BARNDOORINSTALLATION

5.INSTALLATION

●RIGGING

●POWERCONNECTIONS

●DMXCONTROLCONNECTION

●DMXTERMINATOR

6.SETUPANDCONFIGURATION

●FRONTPANELOPERATION

●DMXSTARTADDRESS

●DMXWIRELSESSCONTROL

●STAND-ALONEMODE

●MASTER/SLAVEMODE

7.OPERATIONMENU

8.DMXPROTOCOL

9.LEDINDICATION

10.TECHNICALDATA

11.CIRCUITDIAGRAMANDPCB CONNECTIONS

●CIRCUITDIAGRAM

●PCB CONNECTIONS

12.COMPONENTORDERCODES

ACCESSORIES

Thefollowing itemsare suppliedwith theprojectorand pleasecheck:

Name

Quantity

Unit

Remark

BarnDoor

Set

Optional

Gclamps

Pcs

XLR connector

Set

Maleand female

Safetycord

User manual

Transparent Water proof panel + seal+ screws

Set

Optional for harsh environment installation

likeunderwater,dustyarea

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to

change without notice. Whilst every care is taken in the preparation of the manual we reserve the right to change

specifications in the course of product improvement. The publishers cannot be held responsible for the accuracy of the

information herein, or any consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit

are in good condition before installation and use. Should there be any damage caused by transportation, consult your

dealer and do not use the unit. Any damage caused by improper use will not be assumed by the manufacturer and / or

dealer.

Any future technical change in the user manual won’t be with any notice.

Note: Forthe products made by GuangzhouPRlighting Ltd,thewarranty for the whole product isoneyear starting fromthe delivery date

buttheprojectorsourceisnotwithinthewarranty.

1. SAFETYANDWARNINGS

NOTE

Before a projector’s installation, power-on, operation and maintenance, please carefully read

the safety information hereinafter!

Thefollowingsafetysignsareusedinthe usermanual.

Warning

User

Manual

Electrical

shock

Goggles

Protective

Gloves

Flames

High

Temperature

● When unpacking , check if there is transportation damage before using the projector. Should there be any

damagecausedbytransportation,consultyourdealeranddonotuseit.

●The manufacture is not responsible for loss caused bythe user not following the manual or changing the projector

ashe/shelikes

●Pleasebenotedthatthe damagecausedbychangingtheprojectoratwillisnotwarranted.

●Do not hesitate to contact the dealer or the manufacturer if anyquestions or advice.

●The unit can be used indoors and outdoors and for its IP rating .please refer to Technical Data section of this user

manual

●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while

beingoperated

●The projector is only intended for installation, operation and maintenance by qualified personnel. And the

operationmust strictlyfollowtheproceduresinthemanual

●No repairable partsintheprojectoranddo notopencoversfor maintenance byyourself.

●Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned.

●Do notconnectthisdeviceto anytypeofdimmerpack

●Afterlamp switched on,the minimumdistancebetweentheprojectorandilluminatedsurfaceis1.5m

●If projector’s lamp, lens and screen’s protective cover have obvious damage, i.e., the extent to which its

performance hasbeencompromised, likecrackingor deformation.Please stopoperationandcontactthe

manufactureforthereplacement withoriginalparts, otherwisethenormaloperationwillbe affected.

●Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use a

projector whilecovers(housing)areoff

●Keep thelamp cleananddonottouch itwithbare hands.

●While operatingit, wearprotective items.

●Anyelectricalconnectionmustbecarriedoutbyaqualified person.

●Before installation, pleaseconfirmthe voltage supplied matcheswhatisrequiredfortheprojector

●Eachprojectormustbeproperlyearthedand installedasperrelatedelectrical standards.

●Do notusepower cord withitsinsulator damagedandconnectthepowercord withothercables.

●If the projector is not used or under cleaning,, please hold the plug and unplugit. Do not unplug it forcefully

orbypullingthepower cable.

●Allpowercords mustconformto relatedsafetyandregulations

●Whilebeingoperated,theprojectorshouldnotbeunderrainsorinhumidity.

●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other

electricalparts’ lifewillbeshortened.

●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety

cord suppliedthroughthesafetycordholesforsafetysupport.

●Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from

powermains.

●After running for 5minutes at constant temperature environment, the temperature of the housing of the

projector is55℃.Afterstableoperation, itstemperatureis70℃.

●While thelampisstrickenforthefirsttime,therewillbesmokeandstrangesmell.It’s normal and does not

mean theprojectorhas somedefects.

●While operated,do not touchthemetallic housing. It is veryhotduringoperation.

●Do notmounttheprojectordirectlyoninflammablesurface.

●Do not project the beam straightly on combustible items and the minimum distance between the

projector andilluminateditemsis5m.

●Aprojector should be installed with good ventilation and the minimum distance between the projector

andwallsis50cm.Atthesametime, pleaseensurethefans andairinletsandoutletsareworkable.

2. INSTRUCTIONS

●CLEANINGANDMAINTENANCE

The accumulation of oil, smoke and dust on the lens will compromise the light output. Cleaning a projector is very necessary to

ensure a reliable use of it. Without the permissionbya qualified person for internal part replacement, it is forbidden to dismantle a

unit.

Cleaning frequency is to be decided byoperations and itsenvironment. Use soft cloth and normal detergent for glass for cleaning

work. It’s advised external optical system be cleaned every 20days. Keep lens clean and do not touch optical parts with bare

hands.

Special note:

For any waterproof projector, it's normal if there is some mild mist on the lens while in use.

●Beforeany maintenanceandcleaning,pleaseensuretheprojectisoffthepower

●Onlyqualifiedpersonisallowed todomaintenance

●During maintenanceandbeforemaintenance,theprojectormustbeoff power.

●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens

whether itrunsornot

●Do notusealcoholorother organic solventto clean the housingtoavoiddamage.

●Do notuseany solventwithchemical elementsto cleancolor filtersor hot mirror.

●TROUBLESHOOTING

PROBLEM

ACTION

The projector can’t be switched on

Checkifthe powercord is connected well

Power Supply damaged or not connected well, a qualified technician

needed

Control Boardis not connected welland aqualified technicianneeded

Theprojectorcanbeswitched on,buttheLED

lamp can’t be turned on and controllable

LEDlampboardisnot connected wellandaqualifiedtechnicianneeded

Thelampison but the projector doesn’t respond

to thecontroller

Makesurethatthe fixture’s start address is right

Replace orrepair theXLRsignalcable.

Beam appearsdim, Lowinbrightness

Environment is too hot, thus making the projector very hot. Necessary

coolingmeasuresneeded

3.APPEARANCE

4. INSTALLATIONOFBARN DOOR

Ifthebarndoorissupplied,itsinstallationisasfollows:

Place barn door support 14 via threads in the head 15, then use 4 screws 12 to mount the barn door on the barn door support to

completeitscompletion.Toachievelight closingeffect desired,adjusttheangleofthebarndoor blades.

Head

Handle

Power Supply Box

Barn Door

Head

5. INSTALLATION(Forreferenceonly)

●RIGGING

Beforemovingtheunit,lock theadjustingknob.

Take 2 clamps and the safety cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached

to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNING on the

underside ofthe base as shown above) To pass the SAFETY CORD through the HOLES for safety! Always ensure that the

projector is firmlyanchored to avoid vibrationandslippingwhilstfunctioning. Alwaysensure thatthestructurethatyouaregoing

to mountthe projectortoissecureandstrongenough tosupporttheweightofaunit.

WARNING:

●The projectorMUSTbe liftedorcarriedbythe HANDLESinsteadofclamps.

●.Forsafetythesafetycord should afford10times the Projector’s weight.

●POWERCONNECTION

Connectthe powercordasfollows:

L(live)=brown

E(earth)=yellow/green

N(neutral)=blue

Note:Beforepowerconnection,pleaseensurethe powersuppliedmust matchwhatthenameplatesays.

●The earth wire(yellow/green) must be connected to the ground. And electrical connection must be in

accordance with the standardsconcerned.

●Ifanyquestionsabouttheelectricalinstallation,donotcontinuebutconsultaqualifiedelectrician.

Clamp

Safety Cord

Handle

Adjusting Knob

Warning: please run

the safety cord through

the arm for safety.

●DMXCONTROLCONNECTION:

Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with

each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 3 pin (which are included with the

projector)or3pinXLRplugsand sockets.The XLR'sareconnectedasshownin thefigureabove.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets

mustn’t be connected in any way other than mentioned in the above figure. The projector accepts digital control signals in protocol

DMX512(1990).

Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second

fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX

terminatorasshowninthe figurebelow.

●DMXTERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electrical noise fromdisturbingandcorruptingtheDMXcontrolsignals.

The DMX terminator is simply an XLR connector with a 120(ohm) resistor connected across pins 2 and 3, which is then plugged

intotheoutputsocketonthe lastprojectorinthechain.Theconnectionsare illustrated below.

DMX IN DMX OUT DMX IN DMX OUT DMX IN DMX OUT

POWER POWER POWER

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain. PIN 3

PIN 2

6. SETUPANDCONFIGURATION

●FRONTPANELOPERATION

Projectorconfigurationcanbesetconveniently via pushbuttonandLCDdisplay.

Launch the projector and pressbutton ENTER for more than 3 seconds to unlock the panel, the LCD will show the function menu of

the projector, each main menu has its submenus and each submenu has a specific function. For details, please see the

“OPERATION MENU” section.

Pressbutton UP or DOWN ifyouwant tobrowsethroughthevariousSetupOptions.

Pressbutton ENTER tosave your settingsorenter thesubmenu.

Pressbutton UP or DOWN tochangevalues(plusor minus)

Pressbutton FUNC,it willreturnto theupper menu.Ifbutton FUNC notpressed,thedefaultwillshowdisplaystatusautomatically.

●DMX STARTADDRESS

EachProjectormust be givena DMXstartaddressso thatthecorrectprojectorrespondsto the correct controlsignals.This DMX start

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the

controller. The Unit has 2 DMX modes. Thereare standard mode and extended mode. For example standard mode has6 channels,

so set the No. 1 projector’s address 001, No. 2 projector’s address 007, No. 3 projector’s address 013, No. 4 projector’s address019,

andsoon.

Launchtheprojector.Pressbutton ENTER more than2secondsto unlockpanel.

Pressbutton ENTER todisplayDMXaddress;

Pressbutton UP and DOWN, youcansettheaddress;

Pressbutton ENTER toconfirm;afterpoweredonnexttime,thedefault willbe lastvalue saved

Pressbutton FUNC,it willreturnto theuppermenu

●DMXWIRELESSCONTROL(Iftheprojectorhasthefunction)

Theprojectorhaswirelesscontrol functionwith wirelessreceivermoduleandantennafor remotecontrol.

Thesetupofitisbelow:

1. Enter into the projector’s menu. Select the menu “Config Settigns” via the bottoms of UP and DOWN

2. Select DMX control Mode---- Wireless First (Note: do not select XLR ONLY),then wireless indication in the

front panel will beon, meaning wirelesscontrolfunction isactivated.

Only after the projector is linked with a transmitter, can it receive wireless signal sent by the transmitter. If unlinking it,

Press “Enter” for the menu of Unlink Wireless under the upper level menu of Config Settigns.

●STAND-ALONEMODE

Operate the projector without connecting with a controller, enable the master mode through the operation panel, the

projector will run in Stand-Alone mode automatically.

DMX address can be set at any number within 512.

●MASTER/SLAVEMODE

Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,

connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR controlcable and then connect the second

fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the

last fixture’s DMX output to a DMX terminator. Set 1st projector as the master and others are Slaves.

StartAddressesofall Slaves are 001; Operation mode of the Master can be set any mode for a Master’ and Slaves’ operation mode can

besetaccordingly.

AfterPoweredon,the group willruninMaster/Slave Mode

7. OPERATIONMENU

1st levelmenu

2nd levelmenu

3rd level menu

4th levelmenu

DMXAddress

Standard mode:001–507

Extended: 001-502

HSI:001-508

HSIC:001-507

ConfigSetup

DMX ChannelMode

Standard6

Default：Standard 6

Extended 11

HSI 5

HSIC 6

DMX Mode

XLR Only

Default：XLR First

WirelessOnly

XLR First

WirelessFirst

WirelessToXLR 出

UnlinkWireless

Yes

LED OuptControl

Default:NO

Brightness

Timercontrol

MasterSlave

Slave

Default：Slave

Master

ColorOffset

Red

128-255

Green

128-255

POWER IN

DMX IN

DMX OUT DMX OUT

DMX IN

DMX OUT

DMX IN

Master Slave Slave

POWER IN POWER IN

Blue

128-255

LanguageSetup

English

Default：English

Chinese

LcdLightSetup

Backlightoff3 minutes afterno

buttonpushed

Off

DisplayInvert

Yes

FactorySetting

Yes

PRMTransmit

Yes

cleanProgra

Yes

INFO

LEDTemperature

XXX

DisplayofLampboardtemperature

Fixture useTime

XXXX

DisplayofFixturetime

RDM Device Lab.

RDM

ANSI E1.20

SoftwareVer.

X.X.X

DisplayofSoftwareVersion

TestMode

Red

Green

Blue

White

RGB

RWB

RGBW

OperationMode

DMX Mode

Yes

UserMemory

Yes

PresetMemory

（PR01~PR16）

UserPrograEdit

（ET01~ET16）

Dimmer

000 -255

Strobe

000 -255

Red

000 -255

Green

000 -255

Blue

000 -255

White

000 -255

Hue

000 - 255

Saturation

000 - 255

KeepTime

000 –200 (0-20S)

Timerbrightness

Currenttime

Hour

0-23

Min

0-59

LEDontime

Hour

0-23

Min

0-59

LEDofftime

Hour

0-23

Min

0-59

LEDonbybri.

001-100

LEDoffbybri.

001-100

CheckBrightness

001-101

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PR Lighting Beleuchtungsausrüstung Handbücher

PR Lighting

PR Lighting PR-2203 XR 200 Bedienungsanleitung

PR Lighting

PR Lighting XR 200 BEAM Leitfaden

PR Lighting

PR Lighting AQUA 350 BEAM Bedienungsanleitung

PR Lighting

PR Lighting CENTURY SPOT PR-2002 Bedienungsanleitung

PR Lighting

PR Lighting AQUA LED 1500 SPOT Bedienungsanleitung

PR Lighting

PR Lighting XLED 4007 BEAM Bedienungsanleitung

PR Lighting

PR Lighting PR-8121 Bedienungsanleitung

PR Lighting

PR Lighting TANGO SPOT Bedienungsanleitung

PR Lighting

PR Lighting XR250 Bedienungsanleitung

PR Lighting

PR Lighting XR 380 BWS Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Bedienungsanleitung

PR Lighting

PR Lighting PR-2900 Bedienungsanleitung

PR Lighting

PR Lighting XR 1400 Framing Bedienungsanleitung

PR Lighting

PR Lighting XPAR 354 Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Bedienungsanleitung

PR Lighting

PR Lighting PR-8120 Bedienungsanleitung

PR Lighting

PR Lighting XPar 150 Zoom Bedienungsanleitung

PR Lighting

PR Lighting DESIGN 150 Bedienungsanleitung

PR Lighting

PR Lighting AQUA LED 3000-W FRAMING Bedienungsanleitung

PR Lighting

PR Lighting PR-8170A Bedienungsanleitung

PR Lighting

PR Lighting AQUA 580 BWS Bedienungsanleitung

PR Lighting

PR Lighting PR-8920 Bedienungsanleitung

PR Lighting

PR Lighting TANGO FRAMING Bedienungsanleitung

PR Lighting

PR Lighting Mega Colour 2500 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung