PR Lighting PR-8920 Bedienungsanleitung

NAME: Pro Stage 348

MODEL: PR-8920

This product manual contains important information about the safe installation and use of this lighting fixture.

Please read and follow these instructions carefully and keep this manual in a safe place for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

2/14

INDEX

SAFE USAGE OF THE LIGHTING FIXTURE…………………………………………………………………. 2

INSTALLING THE LIGHTING FIXTURE……………………………………………………………………... 4

CONTROLSYSTEMAND POWER CONNECTIONS………………………………………………………..... 4

DMX TERMINATOR………………………………………………………... ……………………………...... 5

SETUPOPTIONS- LIGHTING FIXTURE CONFIGURATION…………………………………………………. 5

TO SETTHE DMX STARTADDRESS………………………………………………………... ……………… 6

OPERATION MENU………………………………………………………... ……………………………....... 7

DMX PROTOCOL………………………………………………………... ……………………………......... 7

INDICATION OF LED DISPLAY……………………………………………………….................................... 8

MAINTENANCE………………………………………………………............................................................. 8

TROUBLESHOOTING………………………………………………………..................................................... 8

TECHNICALDATA………………………………………………………......................................................... 9

ELECTRICALDIAGRAM………………………………………………………............................................... 11

COMPONENT ORDER CODES………………………………………………………...................................... 12

BACK COVER………………………………………………………................................................................ 14

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to

change without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change

specifications in the course of product improvement. The publishers cannot be held responsible for the accuracy of the

information herein, or any consequence arising from them.

Every unit is completely tested and properly packed by the manufacturer. Please make sure the packing and / or the unit are in good condition before

installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the unit. Any damage caused by improper

use will not be assumed by the manufacturer and / or dealer

ACCESSORIES

These items are packed together with the lighting fixture

Name Quantity Unit Remark

Safety cord 1 Pc

User’s Manual 1 Pc

Clamp 1 Pc

SAFE USAGE OF THE LIGHTING FIXTURE

When unpacking and before disposing of the carton, check there is no transportation damage

before using the lighting fixture. Should there be any damage caused by transportation,

consult your dealer and do not use the apparatus.

Please make sure that a lighting fixture's cover mustn't be tightened fully for allow

ance for some movement, otherwise, it will be expanded after heated resulting in the

fixture not being used normally.

3/14

The lighting fixture can be only used indoors, IP20.

The lighting fixture is not designed or intended to be mounted directly on to inflammable surfaces.

The lighting fixture is only intended for installation, operation and maintenance by qualified personnel.

Do not project the beam onto inflammable surfaces, minimum distance is 5m. 5m

Avoid direct exposure to the lightfrom the lamp.The light is harmful to eyes.

Do not attempt to dismantle and/or modify the lighting fixture in any way.

Electrical connection must only be carried out byqualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power requirements of the lighting fixture.

It is essential that each lighting fixture is correctly earthed and that electrical installation conforms to all relevant standards.

Do not connect this device to any other types of dimmer apparatus.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cordcomeintocontactwithothercables.

Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.

When the lighting fixture is hanged to a high place, please use a safety cord provided to pass through the lighting fixture’s handles as a

secondary safety fixing for safety seasons. For details, refer to “INSTALLTHE LIGHTING FIXTURE “section.

Exterior surface temperatures of the lighting fixture after 5 minutes operation is 45℃, when achieving steady state it is55℃.

There is no user serviceable parts inside the lighting fixture, do not open the housing and never operate the lighting fixture with the

covers removed.

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

Always disconnection from power, when the device not in use or before cleaning or any maintenance

work !

4/14

INSTALLTHE LIGHTING FIXTURE

When the lighting fixture is used, put it on a flat surface or hang it. Make sure it is steady and secured.

When the lighting fixture is used at a high place, as the figure above, move the support to the top of the lighting fixture, connect a lamp

hook to the mounting hole reserved in the support by screws, and then hang the hook to mounting bar. Eventually, use the safety cord

provided to pass through the support and hang it as a second safety fixing.

CONTROL SYSTEMAND POWER CONNECTION

DMX 512

2DATA-

DATA+3

1GND

FUNCTION

三芯

DMX OUT DMX IN

THREE-PIN

Connection between the controller and a lighting fixture and between one lighting fixture and another must be made with a 2

core-screened cable, with each core having at least a 0.5mm diameter. Please use the lighting fixture’s cannon 3- pin signal input and

output cables as connection. The 3-pin signal connections are connected as shown in the figure above.

5/14

Note: Care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of the plug is not

connected in any way. The device accepts digital control signals in protocol DMX512 (1990).

Maximum 32 units can be connected in series by 3-pin signal cable. Connect the controller’s output to the first fixture’s input, and

connect the first fixture’s output to the second fixture’s input and connect the rest fixtures in the same way. Eventually connect the last

fixture’s output to a DMX terminator as shown in the figure below.

Note: For synchronous control, StartAddresses for all slave units must be same.

Each unit’s POWER INPUT should be connected to external POWER individually and the voltage and frequency of the power

supplied match what its nameplate describes.

.DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2 and 3, which is then plugged

into the output socket on the last projector in the chain. The connections are illustrated below.

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

SETUPOPTIONS-LIGHTING FIXTURE CONFIGURATION

Lighting fixture configuration can be set conveniently via push-button switch and LED display.

Launch the lighting fixture and press button ENTER for more than 5 seconds to unlock the panel, the LCD will show the function

menu of the lighting fixture, each main menu has its submenus and each submenu has a specific function. For details, please see

the “OPERATION MENU” section.

Press button UP or DOWN if you want to browse through the various Setup Options. Press button ENTER to save your settings or

enter the next menu. Press button UP or DOWN to change values(plus or minus)

6/14

Press button FUNC, it will return to the upper menu one by one or browse through the main menu.

TO SETTHE DMX STARTADDRESS

Each device must be given a DMX start address so that the correct lighting fixture responds to the correct control signals. This DMX

start address is the channel number from which the lighting fixture starts to “listen” to the digital control information being sent out

from the controller. The device has 6 channels, so set the No. 1 lighting fixture’s address 001, No. 2 lighting fixture’s address 007,

No. 3 lighting fixture’s address 013, No. 4 lighting fixture’s address 019, and so on.

Launch the lighting fixture. Press button ENTER for more than 5 seconds to unlock the panel.

Press button FUNC, UP or DOWN to find “AddR” menu.

Then press ENTER to show DMX address and press UP or DOWN to setDMX address.

At this time, the address willflash continuously. Press button ENTER to confirm and it means the setting has been

enabled and saved. After powered next time, the latest setting will be used.

Press button FUNC, it will return to the upper menu one by one.

7/14

DMX PROTOCOL

CHANNELS FUNCTION DMX DESCRIPTION

1 Dimmer 000-255 Linear Dimming from dark to light

2 White 000-255 Linear Dimming from dark to light

3 Red 000-255 Linear Dimming from dark to light

4 Green 000-255 Linear Dimming from dark to light

5 Blue 000-255 Linear Dimming from dark to light

0 No effect

6 Strobe

001-255 Strobe speed from slow to fast

8/14

INDICATION OF LED CHARACTER

On DMX signal OK

DMX Indication Off No DMX signal

Display Information Flash Parameter or Value not saved, please press

ENTER T to save

MAINTENANCE

To prolong the life of the lighting fixture, it is very important to do the maintenance work. Cooling fans must be cleaned once every

15days and external lens cleaned periodically for an optimum light output. DO NOT USE ANY SOLVENT CONTAINING

CHEMICALELEMENT.

Cleaning frequency depends on the environment in which the fixture operates. Soft cloth and typical glass cleaning products should be

used for cleaning with care. It is recommended to clean lighting fixture at least once every 20 days.

Do not use any organic solvent, e.g. alcohol, to clean housing of the apparatus.

TROUBLESHOOTING

PROBLEM ACTION

The lighting fixture doesn’t switch on

¾Power connection is not correct.

¾Power supply is damaged or abnormal. Call a qualified personnel to fix

it.

¾Connection of control board is not correct. Call a qualified personnel to

fix it.

The lighting fixture can be turned on, but LEDs

do not emit light and are out of control.

¾Connection of LED board is not correct. Call a qualified personnel to fix

it.

The lamp comes on but the lighting fixture

doesn’t respond to the controller

¾Make sure that the lighting fixture’s StartAddress is property set..

¾Replace or repair the XLR signal cable.

The beam appears dim ¾The lighting fixture is too hot. Take ventilation measures to make it cool.

9/14

TECHNICAL DATA

VOLTAGES:

100-240V AC，50/60Hz

POWER CONSUMPTION:

100W

LED:

Quantity 48（R:12＋G:12＋B:12＋W:12）

Manufacturers Rated LED Life 50000 Hours

COLOURS:

RGBW linear color mixing with Macro

COLOR TEMPERATURE CORRECTION：

Linear color temperature correction from 3200K to 10000K

DIMMER:

0-100% linearly adjustable

Light Source Luminous Flux

2100 lm

STROBE:

Electronic Strobe 0 ~25F.P.S

LIGHT ANGLE：

Field Angle(1/10 Maximum) θ

horizontal direction 0°~118° vertical direction 0°~92°

CONTROL:

DMX512, 3 pin interfaces

6 channels in standard mode,

HOUSING:

High Tensile Extruding Aluminum, IP20

WORK ENVIRONMENT TEMPERATURE:

-20°C~40°C

WEIGHT:

Net Weight: 7Kg Gross Weight: 9Kg

10/14

Light Output （vertical direction）

SIZES:

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PR Lighting Beleuchtungsausrüstung Handbücher

PR Lighting

PR Lighting XR130 Beam Bedienungsanleitung

PR Lighting

PR Lighting XR 1400 Framing Bedienungsanleitung

PR Lighting

PR Lighting PR-2330 Bedienungsanleitung

PR Lighting

PR Lighting PR-8835 Bedienungsanleitung

PR Lighting

PR Lighting PR-8120 Bedienungsanleitung

PR Lighting

PR Lighting XLED 590 Bedienungsanleitung

PR Lighting

PR Lighting PR-111ER MOON Bedienungsanleitung

PR Lighting

PR Lighting ARC LED 372 Bedienungsanleitung

PR Lighting

PR Lighting Mega Colour 2500 Bedienungsanleitung

PR Lighting

PR Lighting XR 200 BEAM Leitfaden

PR Lighting

PR Lighting XL WASH 700 Bedienungsanleitung

PR Lighting

PR Lighting PR-2001L Bedienungsanleitung

PR Lighting

PR Lighting CENTURY SPOT PR-2002 Bedienungsanleitung

PR Lighting

PR Lighting AQUA 380 BEAM Bedienungsanleitung

PR Lighting

PR Lighting XPAR 354 Bedienungsanleitung

PR Lighting

PR Lighting TANGO SPOT Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Bedienungsanleitung

PR Lighting

PR Lighting XR250 Bedienungsanleitung

PR Lighting

PR Lighting XPar 360 Bedienungsanleitung

PR Lighting

PR Lighting LS150 TREE Bedienungsanleitung

PR Lighting

PR Lighting XL 1500 Bedienungsanleitung

PR Lighting

PR Lighting XL 1500 Bedienungsanleitung

PR Lighting

PR Lighting Junior JNR-8142D Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung