PR Lighting CENTURY SPOT PR-2002 Bedienungsanleitung

CENTURY SPOT

PR-2002

This product manual contains important information about the safe installation and

use of this projector. Please read and follow these instructions carefully and keep this

manual in a safe place for future reference.

PR LIGHTING LTD.

Yingbin Road, Dashi Panyu, Guangzhou, 511430 China

http://www.pr-lighting.com

Century Spot manual_Last Revision_en.doc

2/14

SECTION PAGE

SAFE USAGE OF THE PROJECTOR 3

STRUCTURE 4

FITTING THE LAMP 4

POWER SUPPLY –MAINS 4

OPERATION 5

STAND-ALONE MODE 6

XLR CONNECTORS AND TERMINATOR 6

MASTER/SLAVE MODE 7

CONTROLLER MODE -DMX 512 OPERATION 8

MAINTENANCE 9

KEEPING THE PROJECTOR CLEAN 9

TROUBLESHOOTING 9

TECHNICAL DATA 10

ELECTRICAL DIAGRAM 11

COMPONENT ORDER CODES 12

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change

without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the

course of product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any

consequence arising from them. Please refer to our product if you find any difference between this preliminary issued manual

and product.

Every apparatus has been tested completely and packed properly by the manufacturer. Please make sure the packing and / or

the apparatus is in good condition before your installation and use. Should there be any damage caused by transportation,

consult your dealer and do not use the apparatus. But any damage caused by improper use will not be assumed by the

manufacturer and / or dealer.

THESE ITEMS ARE PACKED TOGETHER WITH THE PROJECTOR

Waterproof plug (1PCS)

XLR control cable with 3-pin plug and socket (1PCS)

This manual (1PCS)

Thank you for purchasing the product Century Spot, PR-2002.

This product manual contains important information about the safe installation and use of this

projector. Please read and follow these instructions carefully and keep this manual in a safe place

for future reference.

The Century Spot is an innovative projector with an elegant housing made from high quality

aluminium-alloy with an epoxy paint finish. The Century Spot complies to CE norms and

standards and uses international protocol DMX-512.

The Century Spot features full CYM colour mixing with high resolution stepper motors, and an

independent adjustable linear mechanical dimmer 0-100%. The protection against dust and liquid

is very high, IP 44, and guarantees perfect functions even in unfavorable weather conditions. The

angle of inclination of the projector-head is adjustable easily from 15° to 90°. It is an ideal

luminaire to lighten buildings, exhibitions or for artistic applications.

ACCESSORIES

INDEX

INTRODUCTION

Century Spot manual_Last Revision_en.doc

3/14

The following points are important for safety as well as for the smooth

installation and performance of the unit.

When unpacking and before disposing of the package check there is no transportation damage

before using the projector. Should there be any damage caused by transportation, consult your

dealer and do not use the apparatus. Keep the package well for your possible future

transportation.

The projector is intended for outdoor use and is splash-proof, IP44. Install only in dry and plain

locations. Avoid excessive moisture.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

The projector must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that all the cooling fans run normally and no ventilation slots are

blocked.

Do not project the beam onto inflammable surfaces. Minimum distance is 5m. 5m

Avoid direct exposure to the light from the lamp. The light is harmful to the eye.

Do not attempt to dismantle and / or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power

requirements of the projector. Only use the lamp with the specified type and rating.

It is essential that each projector is correctly earthed and that electrical installation conforms to all

relevant standards.

Do not connect this device to any dimmer pack.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the

power-cord come into contact with other cables. Only handle the power-cord by the plug. Never

pull out the plug by tugging the power-cord.

Keep the lamp clean. Do not touch the lamp glass with bare hand.

The lamp used in this projector is a high power discharge lamp. After being switched off don’t

attempt to restart the projector until lamp has cooled, this will require approx 15 minutes.

Switching the lamp on and off at short intervals will reduce the life of both the lamp and the

projector. Occasional breaks will prolong the life of both the lamp and the projector.

Never run the projector without a lamp.

There is no user serviceable parts inside the projector do not open the housing and never operate

the projector with the covers removed.

Always disconnect from the mains, when the device is not in use or before

cleaning it or before attempting any maintenance work.

If you have any questions, don’t hesitate to consult your dealer.

SAFE USAGE OF THE PROJECTOR

Century Spot manual_Last Revision_en.doc

4/14

Caution: For the safety reason, remove the sponge between the colour filters before the 1st

application of luminaire.

Position the projector-head facing the sky and lock it via locking knob.

Remove the projector-head cover by loosening the 4 retaining clips.

Open the dichroic-colour-filter bracket by undoing the 2 M6 knurled-screws.

Insert the lamp in the lamp-holder, and ensure PST (pumping stem tip off) on the lamp is at a right

angle (90°) to the beam path. Don’t touch the bulb by bare hand.

Close the dichroic-colour-filter bracket and install projector-head cover. Make sure that all screws

and retaining clips are tightened.

Note: The HMI series are high-pressure lamps with external igniters ( ). Care should always be

taken when handling these lamps. Always read the manufacturers "Instructions for use" enclosed

with the lamp.

Use the plug provided to connect the mains power to the projector paying attention to the voltage

and frequency marked on the panel of the projector. It is recommended that each projector be

supplied separately so that they may be individually switched on and off.

STRUCTURE

FITTING THE LAMP

POWER SUPPLY -MAINS

Century Spot manual_Last Revision_en.doc

5/14

When the power is switched on, the apparatus automatically starts to run the programmes of self-

test. After finishing these, the apparatus is ready for the following operation.

Remove the cover of the control panel. You will see the panel as shown in the figure below.

The right red LED flashes means there is a DMX signal receiving.

Press the button RESET to reset the DMX start address and functions, and the left green LED

will flash one time.

TO SET THE DMX START ADDRESS

See the panel above.

The digital screen will display the DMX start address.

Press the button UP or DOWN, you can change the start address.

Press the button ENTER to confirm. The green LED will flash one time, which means that

apparatus has saved your setting.

The setting will be displayed when you turn on next time.

In stand-alone mode, the DMX start address could be set any value. In master/slave mode, refer

to the chapter MASTER/SLAVE MODE. In controller mode, the address of each apparatus must

be set correctly so as to be controlled respectively. Refer to the chapter CONTROLLER MODE.

TO SET THE FUNCTION

Press the button FUNC consecutively, the digital screen will display in turn the function code 1~9,

A, b. Each one represents one function. You can see the following table for details.

When you locate the function code, you can press button UP or DOWN to display “y” or “n”.

When the digital screen display “y”, you can save and validate it via button ENTER. When the

digital screen display “n”, you can save and invalidate it via button ENTER.

OPERATION

Century Spot manual_Last Revision_en.doc

6/14

CODE OPTION FUNCTION

1YAuto-program enable

2YMaster/Slave mode enable

3Choose 1 of 7 built-in program

4Set time between scenes

5YReset enable

Without connecting the controller, when enable the function 1, the apparatus will run in stand-

alone mode.

In this mode, you can set the DMX start address to any value.

XLR CONNECTORS

Connection between controller and projector and between one projector and another must be

done with 2-core screened cable, with each core having at least a 0.5mm diameter. Connection to

and from the projector is via an XLR control cable with 3-pin plug and socket, which are included

with the projector. The XLR's are connected as shown in the figure above.

Note: care should be taken to ensure that none of the connections touch the body of the plug or

each other. The body of the plug is not connected in any way. The Century Spot accepts digital

control signals in standard DMX512 (1990) format.

5-PIN AND 3-PIN CONVERSION

Century Spot uses 3-pin XLR plug / socket. If your controller uses 5-pin XLR plug / socket, you

should convert 5-pin plug / socket into 3-pin socket / plug as shown below.

STAND-ALONE MODE

XLR CONNECTORS AND TERMINATOR

Century Spot manual_Last Revision_en.doc

7/14

DMX TERMINATOR

In the Controller mode or Master/Slave mode, the DMX output has to be connected with a DMX

terminator at the last fixture in the chain. This prevents electrical noise from disturbing and

corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across

pins 2 and 3, which is then plugged into the output socket on the last projector in the chain. The

connections are illustrated below.

Many luminaires can run synchronously by linking them with each other in the master/slave mode.

Set the address of all luminaires to 001.

Select one luminaire as the master, and set the function code 1and 2to “y”. Don’t connect its

input with an XLR control cable.

Set the function code 1and 2 of the rest luminaries to “n”. Now they are slaves.

Connect the master’s output to the first slave’s input with an XLR control cable, and connect the

first slave’s output to the second slave’s input with an XLR control cable. The rest may be

connected in the same way. Eventually connect the last slave’s output to a DMX terminator as

shown below.

MASTER/SLAVE MODE

Century Spot manual_Last Revision_en.doc

8/14

Century Spot adopts international standard DMX 512 protocol. You may control many luminaires

via controller. When in controller mode, the function code 1and 2 of all luminaires should be set

to “n”, and each apparatus should have specific address to receive the signal from the controller.

Century Spot has 6 channels. So, in controller mode, the address of 1st luminaire is 001; 2nd, 007;

3rd, 013; 4th, 019; etc. Please follow the formula: address of nth luminaire=6 x (n-1) + 1.

Connect the controller’s output to the 1st luminaire’s input, and connect the 1st luminaire’s output

to the 2nd luminaire’s input. The rest may be connected in the same way. Eventually connect the

last luminaire’s output to a DMX terminator as shown below.

DMX CONTROL CHANNEL FUNCTIONS

The Century Spot has 6 channels. They are shown in the following table.

CHANNELS DMX VALUE DESCRIPTION

1 Shutter 000-255 Shutter to open continuous change

2 Cyan 000-255 White to cyan continuous change

3 Yellow 000-255 White to yellow continuous change

4 Magenta 000-255 White to magenta continuous change

5 Focus 000-255 Focusing from big to small

000-249 Reserved

6Control 250-255 Reset

CONTROLLER MODE –DMX 512 OPERATION

Century Spot manual_Last Revision_en.doc

9/14

If the lamp becomes damaged or deformed in any way it must be replaced. If the light from the

lamp appears dim this would normally indicate that it is reaching the end of its life and it should be

changed at once, old lamps run to the extremity of their life may explode. If the projector does not

function, check the fuse in the projector base. It should only be replaced by fuse of the same

specified value 16A/380V (fast blow, ceramic). On the main PCB inside the projector there is also

a fuse rated 4A/250V (fast blow, 5mmx20mm). Should these be damaged call a qualified

technician before replacement. The projector has thermal protection device that will switch off the

projector in case of overheating, should this operate, check that the fans are not blocked, and if

they are dirty clean them before switching on the projector again. Check that the fans are

operational.

Any maintenance work should only be carried out by a qualified technician.

To ensure the reliability of the projector it should be kept clean. It is recommended that the fans

should be cleaned every 15 days. The dichroic colour filters should also be regularly cleaned to

maintain an optimum light output. Do NOT use any type of solvent on dichroic colour filters.

Cleaning frequency depends on the environment in which the fixture operates: damp, smoke or

particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics. A soft

cloth and typical glass cleaning products should be used in cleaning.

Do not use any organic solvent, e.g. alcohol, to clean the housing of the

projector.

PROBLEM ACTION

The projector doesn’t work Check the fuse on the power socket.

Replace the lamp.

The lamp comes on but the projector

doesn’t respond to the controller

Make sure that the projector is correctly

configured.

Replace or repair the DMX cable.

The projector only functions intermittently Make sure the fan is working and not dirty.

Defective projection Check the lenses are not broken.

Remove dust or grease from the lenses.

The projected image appears to have a

halo

Make sure the lamp is installed correctly.

Carefully clean the optical group lenses and the

projector components.

The beam appears dim Check the optics is clean.

Replace with a new lamp of the specified type and

rating.

LIGHT OUTPUT

MAINTENANCE

TROUBLESHOOTING

KEEPING THE PROJECTOR CLEAN

Century Spot manual_Last Revision_en.doc

10/14

Power supply: 220/230V AC 50/60Hz

Power consumption: 2800W

Lamp: OSRAM HMI 2500W/SE, single end

Colour temperature: 6000°K

Manufacturers Rated Lamp life: 500 Hours

Protocol: Standard DMX 512

Running mode: Stand-alone, Master/Slave, and DMX Controller

DMX channels: 6 channels

Colours: 3 basic colours, CYM 256 colours continuous mixing, white, blackout

Beam coverage: 12° -35°

Tilt angle: Adjustable from 15° to 90°

Net weight: 75 kg

Others: Linear dimming from 0-100%, thermal cut-off

TECHNICAL DATA

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PR Lighting Beleuchtungsausrüstung Handbücher

PR Lighting

PR Lighting ARC LED 372 Bedienungsanleitung

PR Lighting

PR Lighting AQUA 580 BWS Bedienungsanleitung

PR Lighting

PR Lighting TANGO SPOT Bedienungsanleitung

PR Lighting

PR Lighting PR-8836 Bedienungsanleitung

PR Lighting

PR Lighting XPar 150 Zoom Bedienungsanleitung

PR Lighting

PR Lighting AQUA LED 3000-W FRAMING Bedienungsanleitung

PR Lighting

PR Lighting PR-8846 Bedienungsanleitung

PR Lighting

PR Lighting XL 1500 Bedienungsanleitung

PR Lighting

PR Lighting LS150 TREE Bedienungsanleitung

PR Lighting

PR Lighting PR-2900 Bedienungsanleitung

PR Lighting

PR Lighting PR-2001L Bedienungsanleitung

PR Lighting

PR Lighting CHAMELEON PR-2012H Bedienungsanleitung

PR Lighting

PR Lighting XLED 4007 BEAM Bedienungsanleitung

PR Lighting

PR Lighting XLED 590 Bedienungsanleitung

PR Lighting

PR Lighting XR 380 BWS Bedienungsanleitung

PR Lighting

PR Lighting XR 200 BEAM Leitfaden

PR Lighting

PR Lighting AQUA LED 1500 SPOT Bedienungsanleitung

PR Lighting

PR Lighting PR-111ER MOON Bedienungsanleitung

PR Lighting

PR Lighting PR-8835 Bedienungsanleitung

PR Lighting

PR Lighting XR 1400 Framing Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Bedienungsanleitung

PR Lighting

PR Lighting XL 1500 Bedienungsanleitung

PR Lighting

PR Lighting TANGO FRAMING Bedienungsanleitung

PR Lighting

PR Lighting XR130 Beam Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung