PR Lighting XPAR 354 Bedienungsanleitung

1/1

XPAR 354

PR-6209A

The user manual contains important information about the safe installation and use of a projector. Please read

and followthese instructions carefullyandkeepthemanual inasafeplaceforfuture reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

2/2

INDEX

1.SAFETYANDWARNINGS

2. INSTUCTIONS

●CLEANINGAND MAINTENANCE

●TROUBLESHOOTING

3.APPEARANCE

4.INSTALLATION

●RIGGING

●PLACEAUNITONAFLAT SURFACE

●INSTALLATIONOFACCESSORIES

●TRANSPORTATION

●POWERCONNECTIONS

●DMXCONTROLCONNECTION

●DMXTERMINATOR

5.SETUPANDCONFIGURATION

●FRONTPANELOPERATION

●DMXSTARTADDRESS

●STAND-ALONEMODE

●MASTER/SLAVEMODE

6.OPERATIONMENU

7.DMXPROTOCOL

8.TECHNICALDATA

9.CIRCUITDIAGRAMANDPCB CONNECTIONS

●CIRCUITDIAGRAM

●PCB CONNECTIONS

10.COMPONENTORDERCODES

ACCESSORIES

The followingitems are supplied withtheprojectorand please check:

Name

Quantity

Unit

Remark

clamp

Powercord

XLRloopcable

pcs

Safetycord

User manual

TransparentCover+ seal+ screws×6

Set

Optional

Bar doorassembly+ frost board(optional)

set

Optional

Tophat

Set

Optional

Please note that as part of our ongoing commitment tocontinuous product development, specifications are subject tochange without notice.

Whilst every care is taken in the preparation of the manual we reserve the right to change specifications in the course of product

improvement.Thepublisherscannotbeheldresponsiblefortheaccuracy oftheinformationherein,oranyconsequencearisingfromthem.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good

condition beforeinstallationanduse. Shouldthere beany damagecausedbytransportation, consultyourdealerand donot usetheunit. Any

damagecausedbyimproperusewillnotbeassumedby themanufacturerand/ordealer.

Any future technical change in the user manual won’t be with any further notice.

Note: Forthe products made by GuangzhouPRlightingLtd,thewarrantyfor thewhole product is oneyearstarting fromthe delivery date

butthelightsourceis notwithinthewarranty.

3/3

1. SAFETYANDWARNINGS

NOTE

Before a projector’s installation, power-on,operationandmaintenance,pleasecarefullyread

thesafetyinformationhereinafter!

Thefollowing safetysigns areusedintheusermanual.

Warning

User

Manual

Electrical

shock

Goggles

Protective

Gloves

Flames

High

Temperature

● When unpacking , check if there is transportation damage before using the projector. Should there be

anydamagecausedbytransportation,consultyourdealeranddonotuseit.

●The manufacture is not responsible for loss caused by the user not following the manual or changing the

projectoras he/shelikes

●Please be noted that the damage caused by changing the projector at willis not warranted.

●Do not hesitatetocontactthe dealerorthemanufacturer ifanyquestions or advice.

●The unitcanbeusedindoorsandoutdoorswithIP67.

●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while

being operated

●The projector is only intended for installation, operation and maintenance by qualified personnel. And the

operationmuststrictlyfollowtheproceduresinthemanual

●No repairable parts in the projectoranddo notopencoversfor maintenancebyyourself.

●Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned.

●Do not connect thisdevice to anytypeofdimmer pack

●After lamp switched on, the minimumdistancebetween theprojector and illuminated surfaceis1.5m

●lens and other optical parts shall be replaced immediately if they have deformed or been damaged, otherwise

thelightoutputwillbecompromised.

●Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use a

projectorwhilecovers(housing)are off

●Keep the lamp clean and do not touch it with bare hands.

●While operatingit,wearprotective items.

●Any electrical connection must be carried out by a qualified person .

●Before installation, please confirm the voltage supplied matches what is required for the projector

●Each projector must be properlyearthed and installed asper related electricalstandards.

●Do not use power cord with its insulator damaged and connect the power cord with other cables.

●If the projector is not used or under cleaning,, please hold the plug and unplug it. Do not unplug it forcefullyor

bypullingthepower cable.

●All power cords must conform to related safety and regulations

●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other

electricalparts’ life willbe shortened .

●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety cord

suppliedthroughthesafetycord holesforsafetysupport.

●Before any installation, maintenance and cleaning work, please ensure the projectorisdisconnected frompower

mains.

4/4

●Whileinstablestatus,thetemperatureofthehousing(heatsink)willbe55℃;

●Whilethe lamp is strickenfor the first time, there will be smoke and strange smell. It’s normal and doesnot

meantheprojectorhas some defects.

●While operated, do not touch the metallic housing. It is very hot during operation.

●Do not mount the projector directly on inflammable surface.

●Do not project the beam straightlyoncombustibleitems and theminimumdistancebetween theprojector

and illuminateditems is10m.

●A projector should be installed with good ventilation and the minimum distance between the projector

and wallsis50cm.At the sametime, pleaseensurethefansandairinletsandoutletsareworkable.

2. INSTRUCTIONS

●CLEANINGANDMAINTENANCE

For the units with optical lens, because of the accumulation of the smoke, oil and dust on lens, the light output will be

compromised. For the reliable use of the unit, it is very necessary to keep it clean. The unit is IP67 rating waterproof device.

Unless approval by some professional technician for necessary internal component replacement, it’s forbidden to dismantle the

unit.

Cleaning frequencyis to be decided byoperations and its environment. Use soft clothand normaldetergent for glass for cleaning

work. It’s advised external optical system be cleaned every 20days. Keep lens clean and do not touch optical parts with bare

hands.

●Beforeanymaintenanceand cleaning,please ensuretheprojectisoffthepower

●Onlyqualified personisallowed to do maintenance

●Duringmaintenanceand before maintenance,the projectormustbeoffpower.

●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens whether

itrunsor not

●Do not use alcohol or other organic solvent to clean the housing to avoid damage.

●TROUBLESHOOTING

PROBLEM

ACTION

The projector doesn’t switch on

Checkthe powercord connection

Power Switch fails or is not connected well, call a professional

technicianforrepairingandchecking

Control board is not connected normally, call a professional technician

forrepairingandchecking ,

The projectcanbeturned on,but the LED lamps

can’t be on

LED lamp board is not connected well, call a professionaltechnician for

repairingand checking

The LEDlamps canbeon,butnotcontrolled

byDMX

CheckifDMXStartAddressisproperlyset

CheckifXLRcablefailsornot

Thebrightnessdecreasesobviously

Ambient temperature is too hot which makes the projector too hot,

pleasetakeappropriateventilationmeasures

5/5

3. APPEARANCE

No.

Name

Remarks

Frostboard（Optional）

Frostboard must be used with barn door assembly

Barndoorassembly（Optional）

Allenscrews

Support

Arm

XLRcable

Smallsize

Powercable

Bigsize

Transparent（Optional）

Forharshplaceslikeunderwaterorbeingdusty

barndoor

body

arm

6/6

4. INSTALLATION

●RIGGING

Take 1 clamp and 1 safety cord out from the package and tighten the clamp with the arm, and then mount the whole unit on the truss,

tighten the clamp’s retainers to keep the unit stable. (See the WARNING on the underside of the base as shown above) To pass the

SAFETYCORDthroughtheARM forsafety!Always ensurethatthe unit is firmly anchored toavoid vibrationand slippingwhilst

functioning. Always ensure that thestructure that youare going to mount the unit to is secure and strong enough to support the weight

oftheunit Loosen thebigknob andadjust the head’s angle for the effect desired and the tighten it. The installation is completed.

(ifthe unitis wit wirelesscontrol,while beinghung,theantennashould facedown)

●PLACEAUNITONAFLATSURFACE

Before placing a unit on a flat surface, loosen the small knob with the support and make the angle between the arm and the support

60degrees.Tightenthesmall knob.Loosenhebig knobandadjusttheanglebetweenthearmandunitasdesiredandthentightenit.

●INSTALLATIONOFACCESSORIES

If barn door selected, its installationis illustratedin the diagrambelow:

Loosenthe screw in the shape of a butterfly in the front part of the unit, turn the clipping componentin the shape of 7 by

a little amount, then place the barn door. Turn the clipping component backward and tighten the butterflyscrews. Hook

the safetycord on the barn to the safety cord hole in the middle of the unit to finish the installation ofthe barn door. Turn

thebarndoor,andopen orclosethe barndoorblades toreachtheeffectdesired.

Iftophat is selected,itsinstallationis illustrated inthefigurebelow:

1 2 43

safety cord

clamp

arm

Warning: For safety, please

ensure the safety cord runs

through the arm and is

tightened

7/7

Loosenthescrews(1)intheshape ofbutterflyinthe frontofthe projector(4),,slightlyturnthe clippingcomponent(2) in the shapeof

7,andinstallthe tophat(3).Turntheclippingcomponentopposite,tightenthescrews(1) inthe shapeofbutterfly,runoneendofthe

safetycord though safetycord holeofthe light and theotherthroughthe holeofthe top hat.Atlast,thetop hat isinstalled.

Iffrostboardisselected,it should be used withbarndoorassembly.Anditsinstallationisillustratedbelow:

●TRANSPORTATION

Before transportation, tighten both knobs after the arm and supportare overlapped.

WARNING:

●TheprojectorMUSTbeliftedorcarriedbytheHANDLES insteadofclamps.

●.For safety the safety cord should afford 10 times the Projector’s weight.

●POWERCONNECTION

Connectthepowercordasfollows:

L(live)=brown

E(earth)=yellow/green

N(neutral)=blue

Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended that each

projectorbe connected withpowerseparatelyso that theymaybeindividuallyswitched on andoff.

Note: If projectors are connected in series, please connect POWERIN port of the 1st projector with the Power Mains, then

connectitsPOWEROUTwithPOWERINof the 2nd projector,and soontillall fixturesareconnected.Ifthe voltage supplied

is 200V-240V, the maximum projectors connected is 8pcs, if it is 100V-120V, the maximum is 4pcs. The diameter of the cores

ofthewiresforthePowerin/outcablesmustbeequalorbigger than2.5mm2.

●Theearthwire(yellow/green) mustbe connectedto theground.Andelectricalconnection must bein

accordancewiththestandardsconcerned.

●If any questionsabouttheelectricalinstallation, donot continue butconsult aqualifiedelectrician.

●DMX CONTROLCONNECTION:

螺母×4

柔光板

遮光板组件

barndoorassembly

frostboard

screwX4

8/8

Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with

each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the

projector)or5pinXLRplugs and sockets.TheXLR'sareconnectedasshowninthefigureabove.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets

mustn’t be connected in any way other than mentioned in the above figure. The unit accepts digital control signals in protocol

DMX512(1990).

Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second

fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX

terminatorasshownin the figurebelow.

●DMXTERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electricalnoise fromdisturbingandcorruptingtheDMXcontrolsignals.

The DMX terminator is simply an XLR connector with a 120(ohm) resistor connected across pins 2 and 3, which is thenplugged

into the outputsocketonthe lastprojector inthechain.The connectionsareillustratedbelow.

5. SETUPANDCONFIGURATION

接电源

接控制器

接回路插

POWER IN POWER OUTPOWER OUT

POWER IN

DMX OUT

DMX OUT DMX IN

DMX IN

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain. PIN 3

PIN 2

DMXterminator

DMXController

Power

9/9

●FRONTPANELOPERATION

To browse through or modify the projector’s functions, press key ENTER for more than 3 seconds to unlock the control panel and

enter the menus. To set or browse through the projector’s functions, press key UP or DOWN. Press the key ENTER to enter the

submenusandthecurrentparameters willbe displayed whileflashing.Press key UP or DOWN tochangevalues(plusorminus)

Press key ENTER to save yourchangesand enter into the upper level menuwhileflashingsstop;

Press key FUNC, itwillreturnto theupper menu(parametersnotsaved)orbrowsethrough1st levelmenus;

Press key FUNC for1 secondornone key is pushed for 1minute, themenu willbeescaped and currentoperationmodedisplayed.

●DMX STARTADDRESS

EachProjector mustbegivena DMXstartaddressso that the correctprojectorrespondstothe correctcontrol signals. This DMXstart

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the

controller. The Unit has 2 DMX modes. There are standard and extended modes. For example standard mode has 6 channels, so set

the No. 1 projector’s address 001, No. 2 projector’s address 007, No. 3 projector’s address 013, No. 4 projector’s address019, and so

on.

Launchtheprojector.Press button ENTER more than2secondsto unlockpanel.

Pressbutton ENTER to displayDMXaddress;

Pressbutton UP and DOWN, youcansettheaddress;

Pressbutton ENTER to confirm; after poweredonnext time,thedefault willbe lastvalue saved

Pressbutton FUNC,it willreturnto the upper menu

IfDMXsignalis available, LED indicationison.Otherwiseitisoff.

●STAND-ALONEMODE

Operate the projector without connecting with a controller, enable the master mode through the operation panel, the

projector will run in Stand-Alone mode automatically.

DMX address can be set at any number within 512.

●MASTER/SLAVEMODE

Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,

connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR control cable and then connect the second

fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the

last fixture’s DMX output to a DMX terminator. Set 1st projector as the master and others are Slaves.

StartAddressesofallSlavesare001;Operationmodeof the Master can be set any mode for a Master’ and Slaves’ operation mode can

be set accordingly

AfterPoweredon,the groupwillrunin Master/SlaveMode

6. OPERATIONMENU

1stlevel menu

2nd levelmenu

3rdlevel menu

4thlevel menu

DMXAddress

Standardmode:001-507

Extendedmode:001-502

10/10

Standard6

Default:Standard6

Extended11

MasterSlave

Slave

Default：Slave

Master

ColorOffset

Red

128 -255

Green

128 -255

Blue

128 -255

LanguageSetup

English

Default：English

Chinese

Lcd LightSetup

The LCDbacklightwill

be turned off3minutes

afternonekeyispushed.

Off

DisplayInvert

Yes

FactorySetting

Yes

PRMTransmit

Yes

cleanProgra

Yes

Information

LEDTemperature

FixtureuseTime

XXXX

SoftwareVersion

X.X.X

TestMode

Red

Green

Blue

White

RGB

RWB

RGBW

OperationMode

DMX Mode

Yes

UserMemory

Yes

Preset Memory

（PR01~PR16）

UserPrograEdit

（ET01~ET16）

Dimmer

000 -255

Strobe

000 -255

Red

000 -255

Green

000 -255

Blue

000 -255

White

000 -255

KeepTime

000 –200 (0-20S)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PR Lighting Beleuchtungsausrüstung Handbücher

PR Lighting

PR Lighting XR 200 BEAM Leitfaden

PR Lighting

PR Lighting CUBIX300 Bedienungsanleitung

PR Lighting

PR Lighting Mega Colour 2500 Bedienungsanleitung

PR Lighting

PR Lighting PR-8120 Bedienungsanleitung

PR Lighting

PR Lighting XLED 4007 BEAM Bedienungsanleitung

PR Lighting

PR Lighting LS150 TREE Bedienungsanleitung

PR Lighting

PR Lighting XL WASH 700 Bedienungsanleitung

PR Lighting

PR Lighting XR250 Bedienungsanleitung

PR Lighting

PR Lighting PR-8170A Bedienungsanleitung

PR Lighting

PR Lighting PR-2203 XR 200 Bedienungsanleitung

PR Lighting

PR Lighting XLED 590 Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Bedienungsanleitung

PR Lighting

PR Lighting XR 380 BWS Bedienungsanleitung

PR Lighting

PR Lighting CHAMELEON PR-2012H Bedienungsanleitung

PR Lighting

PR Lighting PR-8920 Bedienungsanleitung

PR Lighting

PR Lighting PR-6000 FRAMING Bedienungsanleitung

PR Lighting

PR Lighting AQUA 580 BWS Bedienungsanleitung

PR Lighting

PR Lighting AQUA LED 3000-W FRAMING Bedienungsanleitung

PR Lighting

PR Lighting PR-111ER MOON Bedienungsanleitung

PR Lighting

PR Lighting PR-8835 Bedienungsanleitung

PR Lighting

PR Lighting AQUA 380 BEAM Bedienungsanleitung

PR Lighting

PR Lighting PR-8836 Bedienungsanleitung

PR Lighting

PR Lighting PR-8121 Bedienungsanleitung

PR Lighting

PR Lighting XR 230 Beam Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung