PR Lighting PR-2900 Bedienungsanleitung

PILOT 1200

PR-2900

This product manual contains important information about the safe installation and

use of this projector. Please read and follow these instructions carefully and keep this

manual in a safe place for future reference.

PR LIGHTING LTD.

No. 571, Yingbin Road, Dashi Panyu, Guangzhou, 511430 China

http://www.pr-lighting.com

SAFE USAGE OF THE PROJECTOR 3

INDEX

INSTALLING THE PROJECTOR 4

FITTING THE LAMP 4

POWER SUPPLY – MAINS 5

CONTROL CONNECTIONS 5

DMX TERMINATOR 6

SETUP OPTIONS-PROJECTOR CONFIGURATION 6

TO SET THE DMX START ADDRESS 6

FUNCTIONS DISPLAY 7

ERRORS DISPLAY 9

REPLACING GOBOS 9

DMX CONTROL CHANNEL FUNCTIONS 10

LED DISPLAY 12

CHANGING BELTS 12

MAINTENANCE 13

LUBRICATION 13

KEEPING THE PROJECTOR CLEAN 13

TROUBLESHOOTING 13

TECHNICAL DATA 15

ELECTRICAL DIAGRAM 17

COMPONENT ORDER CODES 18

CHANGING THE OPERATION FREQUENCY 19

Please note that as part of our ongoing commitment to continuous product development, specifications are

subject to change without notice. Whilst every care is taken in the preparation of this manual we reserve the

right to change specifications in the course of product improvement. The publishers cannot be held responsible

for the accuracy of the information herein, or any consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or

the unit are in good condition before installation and use. Should there be any damage caused by transportation,

consult your dealer and do not use the unit. Any damage caused by improper use will not be assumed by the

manufacturer and / or dealer.

ACCESSORIES

THESE ITEMS ARE PACKED TOGETHER WITH THE PROJECTOR

G clamps (2 PCS)

XLR cable with 3-pin plug and socket (1 PCS)

Safety cord (2 PCS)

Spare gobos (4 PCS)

his manual (1 PCS)

Ωclamps(Options)(2PCS)

Thank you for purchasing our product PILOT 1200, PR-2900.

INTRODUCTION

This product manual contains important information about the safe installation and use of this projector.

Please read and follow these instructions carefully and keep this manual in a safe place for future

reference.

PILOT 1200 is an innovative projector with an elegant housing, which complies to CE norms and

standards and uses international protocol DMX 512.

The projector uses HMI1200W/S discharge lamp and high quality optical system, which produces

bright and beautiful light beam and has 60% output lumen more than the similar products with the

same power consumption. The projector features effects of strobe, frost light, mixed colours and

rainbow, so it is suitable for applications in TV station, disc, singing and dancing stage, nightclub, etc.

Pilot 1200 manual.doc

2/20

SAFE USAGE OF THE PROJECTOR

When unpacking and before disposing of the carton check there is no transportation damage before

using the projector. Should there be any damage caused by transportation, consult your dealer and do

not use the apparatus.

The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain

and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other liquids.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent

wall surfaces. Be sure that no ventilation slots are blocked.

Do not project the beam onto inflammable surfaces, minimum distance is 5m. 5m

Avoid direct exposure to the light from the lamp. The light is harmful to the eye.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power

requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all

relevant standards.

Do not connect this device to any other types of dimmer apparatus.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-

cord come into contact with other cables. Only handle the power-cord by the plug. Never pull out the

plug by tugging the power-cord.

Keep the lamp clean. Do not touch the lamp glass with bare hand.

The projector should always be installed with a secondary safety fixing. A safety cord is supplied for

this; it should be attached as shown in “installing the projector” section.

The lamp used in this projector is an HMI1200W/S discharge lamp. After switching off don’t attempt to

restart the projector until lamp has cooled, this will require approx 15 minutes. Switching the lamp on

and off at short intervals will reduce the life of both the lamp and the projector. But occasional breaks

will prolong the life of the lamp and projector.

Never run the projector without a lamp.

There is no user serviceable parts inside the projector, do not open the housing and never operate the

projector with the covers removed.

Always disconnect from the mains, when the device is not in use or before cleaning it or before

attempting any maintenance work.

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

Pilot 1200 manual.doc

3/20

INSTALLING THE PROJECTOR

4 HOLES FOR

SAFETY CORD

PASSING THROUGH

CLAMPS

SAFETY CORD

(2PCS)

(1PCS PER CLAMP)

SCREWS

HANDLES

(2PCS) (2PCS PER CLAMP)

RETAINERS

CORD

SAFETY

HOLE

WARNING

through 4 HOLES for safety!

To pass 2 SAFETY CORDS

WARNING

through 4 HOLES for sa fety!

To pass 2 SAFET Y CORDS

CORD

SAFETY

HOLE

106

256

(2PCS)

Take 2 clamps and 2 safety cords out from the package and mount 2 clamps on the underside of

fixture with 2 retainers attached to each clamp. Hang the fixture on the structure and fasten the screws

attached to each clamp. (Watch the WARNING on the underside of the base as shown above) To

pass 2 SAFETY CORDS through 4 HOLES for safety! Always ensure that the projector is firmly

anchored to avoid vibration and slipping whilst functioning. Always ensure that the structure that you

are going to mount the projector is secure and is strong enough to support a weight of PILOT 1200.

WARNING: 1. Unlock the PAN and TILT before the 1st application of projector for safety.

2. The projector MUST be lifted or carried by the HANDLES instead of clamps.

FITTING THE LAMP

TILT LOCK

NUTS

BULB PST

Lock tilt before fitting/replacing the lamp.

Loosen 2 M5 screws and open one of the rear covers, you can see the structure as shown in the

figure above.

Loosen 2 nuts at the both ends of lamp and take out the worn-out lamp. Suggest to free one end after

another.

Fit new lamp and fasten 2 nuts at the both ends of lamp. Notes: don’t touch the bulb of the new lamp

with bare hand so as not to influence the beam output; the PST (pumping stem tip off) on the bulb

facing the rear cover with fans perpendicularly and being not in the beam’s way is a must and aids

cooling.

Close the rear cover and fasten 2 M5 screws.

WARNING: The HMI series are high-pressure lamps with external igniters ( ). Care should

always be taken when handling these lamps. Always read the manufacturers "Instructions for

use" enclosed with the lamp.

Pilot 1200 manual.doc

4/20

Connect the power cord as follows:

POWER SUPPLY - MAINS

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Use the plug provided to connect the mains power to the projector paying attention to the voltage and

frequency marked on the panel of the projector. It is recommended that each projector be supplied

separately so that they may be individually switched on and off.

IMPORTANT

It is essential that each projector is correctly earthed and the electrical installation conforms to

all relevant standards. Power consumption of the PILOT 1200 is 1628W.

CONTROL CONNECTIONS

Connection between controller and projector and between one projector and another must be made

with a 2 core-screened cable, with each core having at least a 0.5mm diameter. Connection to and

from the projector is via cannon 3 pin (which are included with the projector) or 5 pin XLR plugs and

sockets. The XLR's are connected as shown in the figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each

other. The body of the plug is not connected in any way. The PILOT 1200 accepts digital control

signals in protocol DMX512 (1990).

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the

second fixture’s input and connect the rest fixtures in the same way. Eventually connect the last

fixture’s output to a DMX terminator as shown in the figure below.

DMX OUTDMX INDMX OUTDMX IN

TERMINATOR

DMX IN FROM

CONTROLLER

DMX IN DMX OUT

Pilot 1200 manual.doc

5/20

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX

terminator. This prevents electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2

and 3, which is then plugged into the output socket on the last projector in the chain. The connections

are illustrated below.

DMX TERMINATOR CONNECTION

Connect a 120Ω(OHM) resistor across

pins 2 and 3 in an XLR plug and insert

into the DMX OUT socket on the last

unit in the chain.

DMX TERMINATOR

SETUP OPTIONS - PROJECTOR CONFIGURATION

Projector configuration can be set conveniently via pressbutton switch and digital display. Turn the

projector on and the digital display will show DMX address you set and save last time and it can be

reset and saved again as you please.

Press button UP or DOWN if you want to browse through the various Setup Options.

Press button ENTER to save your settings or enter the next menu. Press button UP or DOWN to shift

the display between and or change the display of address.

Press button FUNC, it will return to the upper menu one by one. The display will return automatically

to the function of address display if you stay for about 60 seconds defaulted.

E.g. if you want to set the function of Pan、Tilt 16bit precision valid, do as follows: launch the

apparatus; press button FUNC to which is displayed in digital display; press button UP to

; press button ENTER, it will display ; press button UP consecutively to ;

press button ENTER, it will display ; press button ON to ; in the end, press button

ENTER. Well done, you have validated this function now.

If you want to set the function of Pan、Tilt 16bit precision invalid, press button DOWN to ;

Then press button ENTER to invalidate this function.

And, if you want to set another function valid or not, press button FUNC to track back one by one;

then, do the same way of e.g. above.

TO SET THE DMX START ADDRESS

Each PILOT 1200 must be given a DMX start address so that the correct projector responds to the

correct control signals. This DMX start address is the channel number from which the projector starts

to “listen” to the digital control information being sent out from the controller. The PILOT 1200 has 22

channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 023, No. 3 projector’s

address 045, No. 4 projector’s address 067, and so on.

Launch the projector. Press button FUNC to ; press button ENTER, it will display ;

press button UP and DOWN, you can set the address; press button ENTER to confirm.

Pilot 1200 manual.doc

6/20

FUNCTIONS DISPLAY

(RESERVED)

LAMP SWITCH

(RESERVED)

OFF

SLAVE IN MASTER/SLAVE MODE

OFF

MASTER MODE 1

OFF

FIXED GOBO WHEEL LINEAR SWITCH

COLOUR FILTER LINEAR SWITCH

CODER SWITCH(PHOTOCOUPLER POSITIONING)

PAN\TILT 16 BIT PRECISION SWITCH

TILT ANTI-CLOCKWISE ROTATION SWITCH

OFF

PAN ANTI-CLOCKWISE ROTATION SWITCH

ADDR. 001

SET ADDR.

DISPLAY ADDR.

(CONTINUE)

Pilot 1200 manual.doc

7/20

(RESERVED)

MASTER MODE 4

MASTER MODE 3

MASTER MODE 2

eg."H001" MEANS 1 HOUR

DISPLAY TIME

HOUR

OFF

Pilot 1200 manual.doc

8/20

ERRORS DISPLAY

In the course of launch, PILOT 1200 examines automatically whether there are errors and if there are,

it will display information as follows:

INFORMATION ERRORS

Er02 Sensor 1 temperature too high

Er04 Lamp error

Er05 EEPROM error

Er06 Sensor 2 temperature too high

Er09 Gobo rotation reset error

Er10 Gobo change reset error

Er11 Effect wheel reset error

Er12 Colour wheel reset error

Er17 Prism rotation reset error

Er18 Prism change reset error

Er20 Fixed gobos reset error

Er25 Pan motor reset error

Er26 Tilt motor reset error

REPLACING GOBOS

PINCERS

ROTATED GOBO WHEEL

RETAINING SPRING

GOBOS

EFFECT WHEEL

FIXED GOBO WHEEL

Lock Tilt. Loosen 2 screws on the rear cover with fans and open the rear cover with fans. You could

see the structure as shown in the above figure.

For gobos replacement on the fixed gobo wheel: turn the effect wheel and rotated gobo wheel to a

proper position first; take out a gobo from the fixed gobo wheel carefully; fit a new gobo. Note: if the

gobo is a glass one, it should be touched with glabrous, clean and soft tissue or cloth matted between

hand and glass instead of with bare hand.

For filters replacement on the effect wheel: do in the same way of fixed gobo wheel.

For gobos replacement on the rotated gobo wheel: take an appropriate tool to tug the head of

retaining spring up and engage your another hand to take the retaining spring out; take the gobo out;

fit a new gobo and fit the retaining spring. Notes: the gobo cannot be touched with bare hand; never

attempt to dismantle the gobo holder on which you want to replace the gobo; be careful of the gobo

when the replacement is underway and don’t drop it.

Close the rear cover and fasten 2 M5 screws.

Pilot 1200 manual.doc

9/20

The PILOT 1200 uses 22 DMX channels. They are listed in the following table.

Pilot 1200 manual.doc

10/20

CHANNEL DMX DESCRIPTION

000-009 Shuttering

010-024 White

025-039 Strobe 1

040-054 Strobe 2

055-069 Strobe 3

070-084 Strobe 4

085-099 Strobe 5

100-114 Strobe 6

115-129 Strobe 7

130-144 Strobe 8

145-159 Strobe 9

160-174 Strobe 10

175-189 Strobe 11

190-204 Strobe 12

205-219 Strobe 13

220-234 Strobe 14

235-249 Strobe 15

Strobe

250-255 White

000-009 Black

010-024 Open

Dimmer 025-255 Dimming from light to dark (0-100%)

Iris 000-255 Linearly adjust iris from large to small (0=wholly

open; 100=wholly closed)

000-031 White

032-063 Gobo 1

064-095 Gobo 2

096-127 Gobo 3

128-159 Gobo 4

160-167 Rotation speed 1 (slowest)

168-175 Rotation speed 2

176-183 Rotation speed 3

184-191 Rotation speed 4 (fastest)

192-223 Stop rotating

224-231 Reverse rotation speed 1 (slowest)

232-239 Reverse rotation speed 2

240-247 Reverse rotation speed 3

Fixed Gobo

248-255 Reverse rotation speed 4 (fastest)

Pan 000-255 Pan rotation

Tilt 000-255 Tilt rotation

Focus 000-255 Linearly focusing

Zoom 000-255 Zooming with spot from large to small

000-024 White. Note: stay 5 seconds while DMX value is 5, 6

or 7, the function reset perform

025-030 White/colour filter 1

031-036 Colour filter 1

037-042 Colour filter 1/colour filter 2

043-048 Colour filter 2

049-054 Colour filter 2/colour filter 3

055-060 Colour filter 3

061-065 Colour filter 3/colour filter 4

066-071 Colour filter 4

Colour Wheel

072-077 Colour filter 4/colour filter 5

DMX CONTROL CHANNEL FUNCTIONS

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PR Lighting Beleuchtungsausrüstung Handbücher

PR Lighting

PR Lighting XR 200 BEAM Leitfaden

PR Lighting

PR Lighting DESIGN 150 Bedienungsanleitung

PR Lighting

PR Lighting TANGO SPOT Bedienungsanleitung

PR Lighting

PR Lighting PR-6000 FRAMING Bedienungsanleitung

PR Lighting

PR Lighting XR250 Bedienungsanleitung

PR Lighting

PR Lighting PR-8120 Bedienungsanleitung

PR Lighting

PR Lighting TANGO FRAMING Bedienungsanleitung

PR Lighting

PR Lighting PR-8920 Bedienungsanleitung

PR Lighting

PR Lighting XR 380 BWS Bedienungsanleitung

PR Lighting

PR Lighting ARC LED 372 Bedienungsanleitung

PR Lighting

PR Lighting XR130 Beam Bedienungsanleitung

PR Lighting

PR Lighting LS150 TREE Bedienungsanleitung

PR Lighting

PR Lighting AQUA 580 BWS Bedienungsanleitung

PR Lighting

PR Lighting XR 1400 Framing Bedienungsanleitung

PR Lighting

PR Lighting XL 1500 Bedienungsanleitung

PR Lighting

PR Lighting CHAMELEON PR-2012H Bedienungsanleitung

PR Lighting

PR Lighting Mega Colour 2500 Bedienungsanleitung

PR Lighting

PR Lighting AQUA LED 3000-W FRAMING Bedienungsanleitung

PR Lighting

PR Lighting AQUA 380 BEAM Bedienungsanleitung

PR Lighting

PR Lighting PR-8836 Bedienungsanleitung

PR Lighting

PR Lighting AQUA 350 BEAM Bedienungsanleitung

PR Lighting

PR Lighting PR-2330 Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Bedienungsanleitung

PR Lighting

PR Lighting XR 230 Beam Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung