Pro-face PS-3600G Series Bedienungsanleitung

Preface

Thank you very much for purchasing a Pro-face PS-3600G Series Unit (PS3600G-T41, PS3600G-T41-24V), hereafter

referred to as the PS-G.

Before using the PS-G, read this manual thoroughly to familiarize yourself with the PS-G’s operation procedures and

functions.

Product names used in this manual are the trademarks / registered trademarks of their respective owners.

NOTICE

1. Copying this manual’s contents, either in whole or in part, is prohibited without the express permission of Digital

Electronics Corporation, Japan.

2. The information contained in this manual is subject to change without notice.

3. If you should you find any errors or omissions in this document, please contact Digital Electronics Corporation to

report your findings.

4. Regardless of Clause 3 above, Digital Electronics Corporation shall not be held responsible for any damages,

losses or third-party damages resulting from the use of this product.

Essential Safety Precautions

All safety-related procedures stated in this document must be followed to operate the PS-G correctly and safely. Be sure to

read this and any related documents thoroughly to understand the correct operation and functions of the PS-G unit.

Safety Icons

Throughout this manual, these icons provide essential safety information for PS-G operation procedures requiring special

attention. These icons indicate the following levels of danger:

System Design

Indicates situations where severe bodily injury, death or major equipment

damage can occur.

Indicates situations where slight bodily injury or minor equipment damage

can occur.

Indicates actions or procedures that should NOT be performed.

Indicates actions or procedures that MUST be performed to ensure correct

unit operation.

Do not create PS-G touch panel switches that could possibly endanger the safety of personnel or equip-

ment. A malfunction of the PS-G unit, its I/O unit(s), cable(s), or other related equipment can cause unex-

pected output signals, leading to a serious accident. Be sure to design all important machine operation

switches so they are operated via a separate control system, and not via the PS-G.

Do not create PS-G touch panel switches to control machine safety operations, such as an emergency

stop switch. Install these switches as separate hardware switches, otherwise severe bodily injury or

equipment damage can occur.

Be sure to design your system so that a communication fault between the PS-G and its host controller will

not cause equipment to malfunction. This is to prevent any possibility of bodily injury or equipment dam-

age.

Do not use the PS-G as a warning device for critical alarms that can cause serious operator injury,

machine damage or can halt system operation. Critical alarm indicators and their control/activator units

must be designed using stand-alone hardware and/or mechanical interlocks.

Do not use the PS-G with aircraft control devices, aerospace equipment, central trunk data transmission

(communication) devices, nuclear power control devices, or medical life support equipment, due to these

devices’ inherent requirements of extremely high levels of safety and reliability.

Handling

Wiring

Maintenance

Be sure to use redundant and/or failsafe system designs to ensure adequate levels of system reliability

and safety when using the PS-G with transportation vehicles (trains, cars and ships), disaster and crime

prevention devices, various types of safety equipment, non-life support related medical devices, and other

similar equipment.

After the PS-G unit’s backlight burns out the touch panel is still active, unlike the PS-G unit’s “Standby

Mode”. If the operator fails to notice that the backlight is burned out and touches the panel, a potentially

dangerous machine operation error can occur. Therefore, do not create PS-G unit touch panel switches

that may cause injury and/or equipment damage.

If your PS-G unit’s backlight suddenly turns OFF, use the following steps to determine if the backlight is

actually burned out.

1) If the PS-G unit’s “Backlight Control” is not set and the screen has gone blank, your backlight is burned

out.

2) If the PS-G unit’s “Backlight Control” is set to Standby Mode and the screen has gone blank, and touch-

ing the screen or performing another input operation does not cause the display to reappear, your back-

light is burned out.

Do not modify the PS-G unit. Doing so may cause a fire or an electric shock.

Do not operate the PS-G in an environment where flammable gases are present, since it may cause an

explosion.

To prevent an electric shock be sure to disconnect your PS-G unit’s power cord from the power supply

before wiring the PS-G.

Do not use voltage beyond the PS-G unit’s specified range. Doing so may cause a fire or an electric

shock.

Do not connect or disconnect Host and PS-G unit communication cables while the PS-G is turned ON.

The PS-G uses a lithium battery for backing up its internal clock data and the battery may explode if it is

replaced incorrectly. When replacement is required, use a Pro-face-designated replacement or an equiva-

lent product.

SEE 7.5 Replacing the Backup Battery (page7-10)

Installation

Wiring

Maintenance

Unit Disposal

General Safety Precautions

Be sure all cable connectors are securely attached to the PS-G unit. A loose connection may cause

incorrect input or output signals.

Be sure to ground the PS-G unit’s FG wire separately from other equipment FG lines. Also, be sure to use

a grounding resistance of 100Ω or less and a 2mm2[0.0062inch2] or thicker wire, or your country's appli-

cable standard. Otherwise, electric shock or malfunctions may result.

Be sure to use only the designated torque to tighten the PS-G unit’s terminal block screws. If these screws

are not tightened firmly, it may cause a short-circuit, fire or incorrect unit operation.

Be sure that metal particles and wiring debris do not fall inside the PS-G unit. They can cause a fire,

malfunction or incorrect unit operation.

Do not reset or turn the PS-G OFF, or insert or remove the CF Card while the PS-G unit’s CF Card is being

accessed. Otherwise, CF Card internal data may be damaged or lost.

When the product is disposed of, it should be done so according to your country’s regulations for similar

types of industrial waste.

Do not press on the PS-G unit’s display with excessive force or with a hard object, since it can damage the

display. Also, do not press on the touch panel with a pointed object, such as the tip of a mechanical pencil

or a screwdriver, since doing so can damage the touch panel.

Do not install the PS-G where the ambient temperature exceeds the specified range. Doing so may cause

a unit malfunction.

To prevent abnormally high temperatures from occurring inside the PS-G, do not restrict or block the PS-G

unit’s rear-face ventilation slots.

Do not operate the PS-G in areas where large, sudden temperature changes can occur. These changes

can cause condensation to form inside the PS-G, possibly causing it to malfunction.

Do not allow water, liquids or metal fragments to enter inside the PS-G unit’s case, since they can cause

either a malfunction or an electric shock. The allowable pollution degree is 2.

Do not operate or store the PS-G in locations where it can be exposed to direct sunlight, high

temperatures, excessive dust, moisture or vibration.

LCD Panel Usage Precautions

• The LCD panel’s liquid contains an irritant. If the panel is damaged and any of this liquid contacts your skin,

immediately rinse the area with running water for at least 15 minutes. If the liquid gets in your eyes, immediately rinse

your eyes with running water for at least 15 minutes and consult a doctor.

• The PS-G unit’s LCD screen may show unevenness in the brightness of certain images or at some contrast settings.

This is an LCD characteristic and not a product defect.

• The PS-G unit’s LCD screen pixels may contain minute black and white-colored spots. This is an LCD characteristic

and not a product defect.

• The color displayed on the PS-G unit’s LCD screen may appear different when seen from outside the specified viewing

angle. This is an LCD characteristic and not a product defect.

• When the same image is displayed on the PS-G unit’s screen for a long period, an afterimage may appear when the

image is changed. If this happens, turn off the PS-G, wait 10 seconds and then restart the unit. This is an LCD

characteristic and not a product defect.

• To prevent an afterimage:

• Set the PS-G unit’s display OFF feature when you plan to display the same screen image for a long period of time.

• Change the screen image periodically and try to not display the same image for a long period of time.

Do not operate or store the PS-G where chemicals evaporate, or where chemicals are present in the air.

Corrosive chemicals : Acids, alkalines, liquids containing salt

Flammable chemicals : Organic Solvents

Do not use paint thinner or organic solvents to remove dirt or oil from the PS-G unit’s surface. Instead, use

a soft cloth moistened with a diluted neutral detergent.

Do not use or store the PS-G in areas with direct sunlight, since the sun's ultraviolet rays may cause the

LCD’s quality to deteriorate.

Do not store the PS-G in an area where the temperature is lower than that recommended in the PS-G

unit’s specifications. Doing so may cause the LCD display’s liquid to congeal, which can damage the LCD.

Also, if the storage area’s temperature becomes higher than the specified level, the LCD’s liquid may

become isotropic, causing irreversible damage to the LCD. Therefore, only store the PS-G in areas where

temperatures are within the PS-G unit’s specifications.

After turning OFF the PS-G, be sure to wait a few seconds before turning it ON again. The PS-G may not

operate correctly if it is restarted too quickly.

Due to the possibility of unexpected accidents, be sure to back up the PS-G unit’s data regularly.

Information Symbols

This manual uses the following icons:

Indicates a warning or a product limitation. Be sure to follow the instructions given with

this icon to ensure the safe operation of the PS-G.

Contains additional or useful information.

(1) (2) Indicates steps used to accomplish a given task.

Be sure to follow these steps in the order they are written.

*1 Indicates useful or important supplemental information.

Indicates pages containing related information.

SEE

About Trademarks

The company names and product names described in this manual are referred to in this manual by their

trademarks (including registered trademarks) or service marks. These are abbreviated as follows:

The abbreviated trademarks in this manual correspond to the following official trademarks:

Trademark Holder

Microsoft, Windows, Visual C++, Visual Studio,

Visual C#, Visual Basic, ActiveSync, MSDN, Win32 Microsoft Corporation

Intel, Pentium, Intel XScale Intel Corporation

Pro-face Digital Electronics Corporation

IBM International Business Machines Corporation

NEC NEC Corporation

Adobe Adobe Systems Incorporated

Ethernet Western Digital Electric Corporation

Term used in this manual Official Trademarks

Windows CE Microsoft®Windows®CE operating system

Windows XP Microsoft®Windows®XP operating system

Windows 2000 Microsoft®Windows®2000 operating system

eMbedded Visual C++ 4.0 Microsoft®eMbedded Visual C++®4.0

Visual Studio .NET 2003 Microsoft®Visual Studio®.NET 2003

Visual C# .NET Microsoft®Visual C#®.NET

Visual Basic .NET Microsoft®Visual Basic®.NET

ActiveSync Microsoft®ActiveSync®

MSDN MSDN®

Win32 Win32®

Pentium Intel®Pentium®processors

XScale Intel XScale®

Adobe Reader Adobe®Reader®

PS-3600G Series Model Names

The term “PS-3600G” Series refers to the following PS-G model numbers:

Series Model Description Power Input Type

PS-3600G

Series

PS3600G-T41 Windows® CE 5.0 (Japanese/

English version) is preinstalled

as the operating system.

Input voltage AC100 to 240V.

AC type

PS3600G-T41-24V Windows® CE 5.0 (Japanese/

English version) is preinstalled

as the operating system.

Input voltage DC24V.

DC type

Package Contents

The following items are included in the PS-G unit’s package. Before using the PS-G, please check that all items listed here

are present.

PS-G Unit (1) Installation Guide (1) Installation Fasteners (4/set)

Installation Gasket (1) USB Cable Clamp (1)

(Attached to the PS-G unit)

Power Plug (1) USB Holder 1 set

(Attached to the PS-G unit, (one holder and two covers)

PS3600G-T41-24V only)

CD-ROM (1) CF Card (1)

(Attached to the PS-G unit)

This unit has been carefully packed, with special attention to quality. However, should you find anything damaged or

missing, please contact your local PS-G distributor immediately.

• The CD-ROM included in this package contains a User Manual and PS-G Series Recovery

Image files. For details, please refer to the User Manual on the CD-ROM.

Installation

Guide

Andere Handbücher für PS-3600G Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Pro-face Touchscreen Handbücher

Pro-face

Pro-face PS-3600G Series Bedienungsanleitung

Pro-face

Pro-face GP77R Series Gebrauchsanweisung

Pro-face

Pro-face GP4104G1D Bedienungsanleitung

Pro-face

Pro-face PS-3710A Series Bedienungsanleitung

Pro-face

Pro-face GP-3310T Stücklistenhandbuch

Pro-face

Pro-face PL-5900 Series Bedienungsanleitung

Pro-face

Pro-face GP-577R Series Bedienungsanleitung

Pro-face

Pro-face GP-2500 Series Bedienungsanleitung

Pro-face

Pro-face PFXGP4401TADR Bedienungsanleitung

Pro-face

Pro-face GP4000 SERIES Bedienungsanleitung

Pro-face

Pro-face PS-3700A Bedienungsanleitung

Pro-face

Pro-face GP3000 Series Betriebsanleitung

Pro-face

Pro-face FP-3710K Series Bedienungsanleitung

Pro-face

Pro-face PFXGP4502WADW Bedienungsanleitung

Pro-face

Pro-face GP3000 Series Bedienungsanleitung

Pro-face

Pro-face PL-7900 Series Bedienungsanleitung

Pro-face

Pro-face PS-A Series Bedienungsanleitung

Pro-face

Pro-face SP5000 Series Bedienungsanleitung

Pro-face

Pro-face GP-4400 Series Bedienungsanleitung

Pro-face

Pro-face LogiTouch GLC150-BG41-RSFL-24V Bedienungsanleitung

Pro-face

Pro-face GP3000 Series Bedienungsanleitung

Pro-face

Pro-face GP-377RT Bedienungsanleitung

Pro-face

Pro-face PL-6920 Series Bedienungsanleitung

Pro-face

Pro-face GP-2300T Bedienungsanleitung

Beliebte Touchscreen Handbücher anderer Marken

FlowLine

FlowLine Data loop Bedienungsanleitung

ALPEX

ALPEX AEx-8 P Series Bedienungsanleitung

Ltech

Ltech E5S Bedienungsanleitung

Harman

Harman AMX MODERO S MSD-701-L2 Bedienungsanleitung

Acnodes

Acnodes PC 1150 Bedienungsanleitung

AIS

AIS IP10IA99 series Bedienungsanleitung

IBASE Technology

IBASE Technology ASTUT-152-RE1S Bedienungsanleitung

YASKAWA

YASKAWA TP 610C Bedienungsanleitung

B&R

B&R Power Panel C Series Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT321W-521 Bedienungsanleitung

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Bedienungsanleitung

Qomo

Qomo QIT1386 Bedienungsanleitung

DFI

DFI KS104-CD Bedienungsanleitung

AMX

AMX AXP-PPC Leitfaden

Sartorius

Sartorius X3 PR 5410 Bedienungsanleitung

AMX

AMX Modero X Series Bedienungsanleitung

Advantech

Advantech TPC-30 Series Bedienungsanleitung