Pro-Form 500 Ekg Elliptical Bedienungsanleitung

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Keep this manu-

al for future reference.

Model No. PFEVEL2785.0

Serial No.

QUESTIONS?

As a manufacturer,we are com-

mitted to providing complete cus-

tomer satisfaction. If you have

questions, or if there are missing

or damaged parts, please call:

Or write:

ICON Health & Fitness, Ltd.

Unit 4

Revie Road Industrial Estate

Revie Road, Beeston

Leeds, LS11 8JG

email: [email protected]

www.iconeurope.com

Visit our website at

USER’S MANUAL

Serial Number

Decal

08457 089 009

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

HOW TO USE THE ELLIPTICAL EXERCISER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

IMPORTANT PRECAUTIONS

WARNING:Toreduce the risk of serious injury,read the following important precau-

tions before using the elliptical exerciser.

1. Read all instructions in this manual and all

warnings on the elliptical exerciser before

using the elliptical exerciser.Use the ellipti-

cal exerciser only as described.

2. It is the responsibility of the owner to

ensure that all users of the elliptical exercis-

er are adequately informed of all precau-

tions.

3. Keep the elliptical exerciser indoors, away

from moisture and dust. Place the elliptical

exerciser on a level surface, with a mat

beneath it to protect the floor or carpet.

Make sure that there is enough clearance

around the elliptical exerciser to mount, dis-

mount, and use the elliptical exerciser.

4. Inspect and properly tighten all parts regu-

larly. Replace any worn parts immediately.

5. Keep children under 12 and pets away from

the elliptical exerciser at all times.

6. The elliptical exerciser should not be used

by persons weighing more than 115 kg (250

lbs.).

7. Wear appropriate exercise clothes when

using the elliptical exerciser. Always wear

athletic shoes for foot protection.

8. Hold the handlebars when mounting, dis-

mounting, or using the elliptical exerciser.

9. Keep your back straight when using the

elliptical exerciser. Do not arch your back.

10. The pulse sensor is not a medical device.

Various factors may affect the accuracy of

heart rate readings. The pulse sensor is

intended only as an exercise aid in determin-

ing heart rate trends in general.

11. If you feel pain or dizziness whilst exercis-

ing, stop immediately and cool down.

12. When you stop exercising, allow the pedals

to slowly come to a stop.

13. The elliptical exerciser is intended for

home use only. Do not use the elliptical

exerciser in a commercial, rental, or institu-

tional setting.

WARNING:Before beginning this or any exercise program, consult your physician.

This is especially important for persons over the age of 35 or persons with pre-existing health prob-

lems. Read all instructions before using. ICON assumes no responsibility for personal injury or

property damage sustained by or through the use of this product.

BEFORE YOU BEGIN

Congratulations for selecting the new PROFORM®

500 EKG elliptical exerciser. The 500 EKG elliptical

exerciser is an incredibly smooth exerciser that moves

your feet in a natural elliptical path, minimizing the

impact on your knees and ankles. And the unique 500

EKG features adjustable resistance and a simple-to-

use console to help you get the most from your exer-

cise.

For your benefit, read this manual carefully before

using the elliptical exerciser. If you have questions

after reading this manual, please call the telephone

number on the front cover of this manual. To help us

assist you, please note the product model number

and serial number before calling. The model number

is PFEVEL2785.0. The serial number is found on a

decal attached to the elliptical exerciser (see the front

cover of this manual for the location of the decal).

Before reading further, please familiarise yourself with

the parts that are labeled in the drawing below.

Handlebar

FRONT

BACK

Pedal Arm

Pedal Disk Pedal

Console Pulse Sensor

Fan

Wheel

s, Inc.

01/20/04

209489

ADD PART NO. 210125 AND TABLE

1274-10

210125

REVISIONS

DRAWINGS PREVIOUS TO LAST REV. DATE ARE OBSOLETE

DATE

TITLE:TOLERANCESR

BIKES/ELLIP

GYMS

STEPPERS

TREADMILLS

MISC.

.XX

.XXX

ANGLES

PROJECT/MODEL:

NO. PER UNIT:

DWG. NO.

REV. LEVEL: SCALE:SCALE:

SHEET:

This drawing and all information thereof is the property of ICON Health and Fitness, Inc. and is

CONFIDENTIAL. This drawing is NOT to be made public or copied. This drawing is LOANED,

subject to return upon demand, and is NOT to be used directly or indirectly in any way detrimental

to the interests of ICON Health and Fitness, Inc.

DECAL, NON-FREWHL AEROBIC GNRL WRNG

ONE

1-1

PRODUCTSD

100%

REV ECN DESCRIPTION OF CHANGE

209489

ELLIP/BIKES NON FREEWHEEL

Awarning decal has been placed on the

elliptical exerciser. If the decal is missing or

illegible, call the telephone number on the

front cover of this manual and order a free

replacement decal. Apply the decal in the

location shown.

ASSEMBLY

Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the

packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the

included hex keys, assembly requires a phillips screwdriver , an adjustable

spanner , and a rubber mallet .

Use the chart below to identify the small parts used in assembly. The number in parentheses below each part is

the key number of the part, from the PART LIST on page 14. The number after the parentheses is the quantity

needed for assembly. Note: Some parts may have been preattached for shipping. If a part is not in the

parts bag, check to see if it has been preattached.

Pedal Arm Bolt

Set (40)–2 M10 x 25mm

Patch Screw (22)–2

M8 x 53mm Button Bolt (34)–4

M6 x 38mm Button Bolt (50)–4

Washer (48)–4

M8 Split

Washer (59)–4

M6 Nylon

Locknut (27)–4 Wave Washer

(9)–2

M8 Nylon

Locknut (38)–4

M6 x 48mm Flat Head

Screw (36)–4 M8 x 19mm Button

Screw (68)–4

M4 x 20mm

Screw (43)–4

M10 Washer

(35)–2

1. Identify the Front Stabiliser (10). Whilst another person

lifts the front of the Frame (1), attach the Front

Stabiliser to the Frame with two M8 x 53mm Button

Bolts (34), two M8 Washers (48), and two M8 Nylon

Locknuts (38).

2. Whilst another person lifts the back of the Frame (1),

attach the Rear Stabiliser (28) to the Frame with two

M8x53mm Button Bolts (34), two M8 Washers (48),

and two M8 Nylon Locknuts (38).

3. The Console (23) requires four 1.5V “D” batteries;

alkaline batteries are recommended. Remove the

screw from the battery drawer, pull the battery drawer

open, and insert four batteries. Make sure that the

batteries are oriented as shown by the markings

inside the battery drawer. Close the battery drawer

and reattach the screw.

4. Have another person hold the Console (23) in the

position shown. Connect the console wire to the Upper

Wire (44). Next, insert the excess wire down into the

Upright (2).

Attach the Console (23) to the Upright (2) with four M4

x20mm Screws (43). Be careful to avoid pinching

the wires.

Batteries

Screw

43 2

Console Wire

6. Identify the Left Handlebar (6), which is marked with a

sticker. Insert the Left Handlebar into one of the

Handlebar Arms (5); make sure that the Handlebar

Arm is turned so the hexagonal holes are on the

indicated side. Attach the Left Handlebar to the

Handlebar Arm with two M6 x 38mm Button Bolts (50)

and two M6 Nylon Locknuts (27). Make sure that the

Nylon Locknuts are inside of the hexagonal holes.

Do not fully tighten the Button Bolts yet.

Apply a small amount of the included grease to the left

axle on the Upright (2).

Make sure that there are two Small Handlebar

Bushings (49) in the Left Handlebar (6). Slide a

Handlebar Spacer (47) and the Left Handlebar onto the

left axle on the Upright (2) as shown. Make sure that the

Handlebar Spacer is turned so the curved side is fac-

ing the Upright. Tap an Axle Cap (14) onto the axle.

Repeat this step to assemble the Right Handlebar (8)

and the other Handlebar Arm (5).

Grease

Hexagonal

Holes

68 68Make sure that

the wires do

not get pinched

and damaged

during this

step.

5. Whilst another person holds the Upright (2) near the

Frame (1), connect the Upper Wire (44) to the Sensor

Wire (53).

Push the excess wire down into the Frame (1). Slide

the Upright (2) onto the Frame. Becareful to avoid

pinching the wires. Attach the Upright with four M8 x

19mm Button Screws (68) and four M8 Split Washers

(59). Do not tighten the Button Screws yet.

9. Make sure that all parts of the elliptical exerciser are properly tightened. Note: Some hardware may be

left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the ellip-

tical exerciser.

8. Apply a small amount of grease to the axle on the left

Disc Crossbar (16). Slide the Left Pedal Arm (11) and a

Wave Washer (9) onto the axle. Next, slide an M10

Washer (35) onto an M10 x 25mm Patch Screw (22),

and tighten the Patch Screw into the axle.

Next, hold the lower end of the left Handlebar Arm (5)

inside of the bracket on the Left Pedal Arm (11). Apply

grease to a Pedal Arm Bolt Set (40). Attach the Left

Pedal Arm to the left Handlebar Arm with the Bolt Set.

Do not overtighten the Bolt Set; the Handlebar Arm

must pivot freely.

Attach the Right Pedal Arm (12) to the right side of the

elliptical exerciser in the same way.

See step 5. Tighten the M8 x 19mm Button Screws (68)

in the Upright (2).

See step 6. Tighten the M8 x 38mm Button Bolts (50)

in the Handlebar Arms (5).

Grease

22 35

736

7. Identify the Left Pedal Arm (11). Attach a Pedal (13) to

the Left Pedal Arm with two M6 x 48mm Flat Head

Screws (36) as shown.

Attach the other Pedal to the Right Pedal Arm (not

shown) in the same way.

Grease

HOW TO USE THE ELLIPTICAL EXERCISER

HOW TO EXERCISE ON THE ELLIPTICAL

EXERCISER

To mount the elliptical exerciser, hold the handlebars

and step onto the pedal that is in the lowest position.

Then, step onto the other pedal. Push the pedals until

they begin to move with a continuous motion. Note:

The pedal disks can turn in either direction. It is

recommended that you move the pedal disks in

the direction shown by the arrow; however, for

variety, you may turn the pedal disks in the oppo-

site direction.

To dismount the elliptical exerciser, wait until the ped-

als come to a complete stop. Note: The elliptical

exerciser does not have a free wheel; the pedals

will continue to move until the flywheel stops.

When the pedals are stationary, step off the highest

pedal first. Then, step offthe lowest pedal.

Pedal Disk

Pedal

Handlebars

The easy-to-use console offers a selection of features

designed to help you get the most from your workouts.

Follow the instructions below to operate the console.

Turn on the console.

Note: The console requires four 1.5V “D” batteries.

See assembly step 3 on page 5 for battery instal-

lation instructions.

Toturn on the console, press the On/Reset button

(see the drawing above to identify the On/Reset

button). Note: Moving the pedals is another way to

turn on the console.

Begin pedaling and change the resistance of

the pedals as desired.

As you pedal, change the resistance of the ped-

als by pressing the + and – buttons below the

large display. There are ten resistance levels—

level 10 is the most challenging. Note: After the

buttons are pressed, it will take a few seconds for

the resistance to reach the selected setting.

Follow your progress with the small display

and the large display.

The small display will

show your pedaling pace,

in revolutions per minute

(RPM). The indicator bar

in the small display will

increase or decrease in

length as you increase or

decrease your pedaling

pace. Note: When you

use the handgrip pulse

sensor,the small display will show your heart

rate (see step 4 on page 10).

The upper sec-

tion of the large

display will

show the dis-

tance you have

pedaled and the

numbers of

calories

and

fat calories

you have

burned (see FAT BURNING on page 13 for an

explanation of fat calories). The display will

change from one number to the next every few

seconds.

ELPE2785

Display Buttons

Fan Button

On/Reset Button

Resistance Buttons

HOW TO OPERATE THE CONSOLE

Indicator Bar

To view only the distance

you have pedaled or the

number of calories or fat

calories you have burned,

press the upper button on

the left side of the large

display until only the word

DISTANCE, CALORIES,

or FAT CALS appears in the upper section of the

large display; make sure that the word SCAN

does not appear. To again view the distance you

have pedaled and the numbers of calories and fat

calories you have burned, press the upper button

until the word SCAN reappears.

The centre of

the large dis-

play will show

the elapsed time

and your current

pace (pace is

shown in minutes per mile in this section of the

large display). The display will change from one

number to the other every few seconds.

To view only the elapsed

time or your pace, press

the centre button on the

left side of the large dis-

play until only the word

TIME or PACE appears;

make sure that the word

SCAN does not appear.To

again view both the elapsed time and your pace,

press the centre button until the word SCAN

reappears.

The lower sec-

tion of the large

display will show

your pedaling

speed and the

resistance level.

The display will change from one number to the

other every few seconds.

Toview only your pedaling

speed or the resistance

level, press the lower but-

ton on the left side of the

large display until only the

word SPEED or RESIS-

TANCE appears; make

sure that the word SCAN does not appear. To

again view both your pedaling speed and the

resistance level, press the lower button until the

word SCAN reappears.

To reset the displays, press the On/Reset button.

Note: The con-

sole can show

speed and dis-

tance in either

miles or kilome-

ters. The letters

MPH or KM/H will appear in the lower section of

the large display to show which unit of measure-

ment is selected. To change the unit of measure-

ment, hold down the On/Reset button for about six

seconds. Note: When the button is held down, the

fan will turn on for a moment. When the batteries

are replaced, it may be necessary to reselect the

desired unit of measurement.

Measure your heart rate if desired.

If there are thin

sheets of plas-

tic on the metal

contacts on the

handgrips, peel

off the plastic.

Touse the hand-

grip pulse sen-

sor, hold the

handgrips with

your palms resting against the metal contacts.

Avoid moving your hands.

When your pulse is

detected, the heart-

shaped indicator in the

small display will flash

each time your heart

beats. After a moment,

two dashes (– –) will

appear and then your

heart rate will be shown.

For the most accurate heart rate reading, continue

to hold the handgrips for about 30 seconds.

ELPE2785

Upper Button

ELPE2785

Centre Button

ELPE2785

Lower Button

ELPE2785

Metal

Contacts

Andere Handbücher für 500 Ekg Elliptical

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Pro-Form Ellipsentrainer Handbücher

Pro-Form

Pro-Form Stride Select PFEL09807.0 Bedienungsanleitung

Pro-Form

Pro-Form PFEVEL75108.0 Bedienungsanleitung

Pro-Form

Pro-Form 380 Razor Elliptical Bedienungs- und Wartungshandbuch

Pro-Form

Pro-Form 831.23935.0 Bedienungsanleitung

Pro-Form

Pro-Form 480 Le Elliptical Bedienungsanleitung

Pro-Form

Pro-Form PFEL2595.0 Bedienungsanleitung

Pro-Form

Pro-Form SR 30 Bedienungsanleitung

Pro-Form

Pro-Form 300 Zle Elliptical Benutzerhandbuch

Pro-Form

Pro-Form L.E.X PFEL25070 Bedienungsanleitung

Pro-Form

Pro-Form 295 CSE Bedienungsanleitung

Pro-Form

Pro-Form 690 Hr Elliptical Einrichtungshandbuch

Pro-Form

Pro-Form 764hr Bike Bedienungsanleitung

Pro-Form

Pro-Form ZE 6 Bedienungsanleitung

Pro-Form

Pro-Form 780 Cse Elliptical Bedienungsanleitung

Pro-Form

Pro-Form 6.0 Ce Elliptical Bedienungsanleitung

Pro-Form

Pro-Form 595 HR Einrichtungshandbuch

Pro-Form

Pro-Form STRIDE SELECT PFEL3926.0 Bedienungsanleitung

Pro-Form

Pro-Form XP 420 RAZOR Bedienungsanleitung

Pro-Form

Pro-Form 831.280181 Bedienungsanleitung

Pro-Form

Pro-Form heart rate monitor 545S Bedienungsanleitung

Pro-Form

Pro-Form 1050 Sts Elliptical Bedienungsanleitung

Pro-Form

Pro-Form 280 Razor Elliptical Benutzerhandbuch

Pro-Form

Pro-Form 800 Hr Heart Rate Control Elliptical Bedienungsanleitung

Pro-Form

Pro-Form PFCCEL3906.0 Bedienungsanleitung

Beliebte Ellipsentrainer Handbücher anderer Marken

Weslo

Weslo Momentum 4.0 Elliptical Bedienungs- und Wartungshandbuch

Progear Fitness

Progear Fitness Air elliptical pro 1307 Bedienungsanleitung

Torque Fitness

Torque Fitness XPLLP Bedienungsanleitung

Octane Fitness

Octane Fitness PRO3700C Bedienungsanleitung

Xterra

Xterra FS5.8e Bedienungsanleitung

Bodyguard

Bodyguard E-40 Bedienungsanleitung

Bonn Germany

Bonn Germany Concept 2.2 Bedienungsanleitung

Precor

Precor Resolute RSL 620 Bedienungsanleitung

NordicTrack

NordicTrack E 9.2 Elliptical Bedienungsanleitung

Vision Fitness

Vision Fitness X6600iNetTV Bedienungsanleitung

Matrix

Matrix MX-A5x Bedienungsanleitung

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 Bedienungsanleitung

Sears

Sears FREE SPIRIT C249 30737 0 Bedienungsanleitung

True

True FS-64 Bedienungsanleitung

Sport-thieme

Sport-thieme ST 310 Bedienungsanleitung

VIRTUFIT

VIRTUFIT CTR 1.1 Bedienungsanleitung

Kettler

Kettler GIRO C 1 Bedienungsanleitung

CIRCLE FITNESS

CIRCLE FITNESS E7 Bedienungsanleitung