ProLights LumiPix XB050 Bedienungsanleitung
USER MANUAL
REV.01-10/22 English version
LumiPix XB100
IP65 RGB+WW pixel-controlled linear
LED xture
LumiPix XB050
Thank you for choosing PROLIGHTS
Please note that every PROLIGHTS product has been designed in Italy to meet quality and performance requirements
for professionals and designed and manufactured for the use and application as shown in this document.
Any other use, if not expressly indicated, could compromise the good condition/operation of the product and/or be
a source of danger.
This product is meant for professional use. Therefore, commercial use of this equipment is subject to the respectively
applicable national accident prevention rules and regulations.
Features, specications and appearance are subject to change without notice. Music & Lights S.r.l. and all afliated
companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other
loss occasioned by the use of, inability to use or reliance on the information contained in this document.
Product user manual can be downloaded from the website www.prolights.it , or can be inquired to the ofcial
PROLIGHTS distributors of your territory (https://www.prolights.it/sales_network.html).
Scanning the below QR Code, you will access the download area of the product page, where you can nd a broad
set of always updated technical documentation: specications, user manual, technical drawings, photometrics,
personalities, xture rmware updates.
The PROLIGHTS Logo, PROLIGHTS names and all other trademark in this document pertaining to PROLIGHTS services
or PROLIGHTS product are trademarks OWNED or licensed by Music & Lights S.r.l., its afliates, and subsidiaries.
PROLIGHTS is a registered trademark by Music & Lights S.r.l. All right reserved. Music & Lights – Via A. Olivetti, snc -
04026 - Minturno (LT) ITALY.
Visit the download area
of the product page
LUMIPIXXB100LUMIPIXXB050
01PROLIGHTS - LumiPix XB050 / LumiPix XB100
INDEX
SAFETY INFORMATION 02
1 - PACKAGING 05
PACKAGE CONTENT..................................................................................................... 05
OPTIONAL ACCESSORIES............................................................................................. 05
2 - TECHNICAL DRAWING 05
3 - INSTALLATION 06
MOUNTING.................................................................................................................... 06
4 - CONNECTION TO THE MAINS SUPPLY 07
5 - START UP 07
CONNECT AND DISCONNECT POWER FROM THE PRODUCT.................................. 07
6 - PRODUCT OVERVIEW 08
7 - DMX CONNECTION 09
CONNECTION OF THE CONTROL SIGNAL: DMX LINE .............................................. 09
INSTRUCTIONS FOR A RELIABLE DMX CONNECTION ............................................... 09
CONNECTION DAISY CHAIN........................................................................................ 09
CONNECTION OF THE DMX LINE................................................................................ 09
CONSTRUCTION OF THE DMX TERMINATION ........................................................... 10
DMX ADDRESSING ........................................................................................................ 10
ETHERNET CONNECTION ............................................................................................ 10
ETHERNET OPERATION ................................................................................................ 10
ETHERNET TO DMX OPERATIONS ............................................................................... 11
OPERATION AS A WIRELESS TRANSMITTER................................................................ 11
IN TO WDMX ................................................................................................................. 11
OPERATION AS A WIRELESS RECEIVER........................................................................ 12
WDMX TO DMX (RX)...................................................................................................... 12
8 - CONTROL PANEL 13
DISPLAY AND BUTTONS LAYOUT................................................................................. 13
9 - MENU STRUCTURE 14
10 - SHORTCUT 19
11 - RDM FUNCTIONS 20
12 - DMX CHARTS 24
13 - ACCESSORIES INSTALLATION 78
BARNDOOR (CODE LPXB050BD / LPXB100BD - OPTIONAL)...................................... 78
60° EGGCRATE (CODE LPXB050EC60 / LPXB050EC100 - OPTIONAL)........................ 79
LIGHT DIFFUSION FILTER (CODE LPXB050FILT20/40/60 / LPXB100FILT20/40/60 -
OPTIONAL)..................................................................................................................... 80
14 - TEST OF IP65 RATING 81
15 - MAINTENANCE 82
MAINTENANCE AND CLEANING THE PRODUCT........................................................ 82
VISUAL CHECK OF PRODUCT HOUSING ..................................................................... 82
TROUBLESHOOTING..................................................................................................... 83
PROLIGHTS - LumiPix XB050 / LumiPix XB10002
SAFETY INFORMATION
WARNING!
• Please read carefully the instruction reported in this section before installing, powering,
operating or servicing the product and observe the indications also for its future handling.
This unit is not for household and residential use, only professional applications.
Connection to mains supply
• The Connection to the mains supply must be carried out by a qualied electrical
installer.
• Use only AC supplies 100-240V 50-60 Hz, the xture must be electrically connected
to ground (earth).
• Select the cable cross section in according with the maximum current draw of the
product and the possible number of products connected at the same power line.
• The AC mains power distribution circuit must be equipped with magnetic+residual
current circuit breaker protection.
• Do not connect it to a dimmer system; doing so may damage the product.
Protection and Warning against electrical shock
• Do not remove any cover from the product, always disconnect the product from AC
power before servicing.
• Ensure that the xture is electrically connected to ground (earth). And use only a
source of AC power that complies with local building and electrical codes and has
both overload and ground-fault (earth-fault) protection.
• Before using the xture, check that all power distribution equipment and cables are
in perfect condition and rated for the current requirements of all connected devices.
• Isolate the xture from power immediately if the power plug or any seal, cover, cable, or
other components are damaged, defective, deformed or showing signs of overheating.
• Do not reapply power until repairs have been completed.
• Refer any service operation not described in this manual to PROLIGHTS Service team
or an authorized PROLIGHTS service center.
Installation
• Make sure that all visible parts of the product are in good visible condition before its
use or installation.
• Make sure the point of anchorage is stable before positioning the projector.
• When suspending the xture above ground level, secure it against failure of primary
attachments by attaching a safety cable that is approved as a safety attachment for
the weight of the xture to the attachment point on the main frame of the product. ln
case the safety cable, enter in action, it needs to be replaced with a new one.
• Install the product only in well ventilated places.
• For non temporary installations, ensure that the xture is securely fastened to a load-
bearing surface with suitable corrosionresistant hardware.
• For a temporary installation with clamps, ensure that the quarter-turn fastener and/or
screws are turned fully, and secured with a suitable safety cable.
0.5 m Minimum distance of illuminated objects
• The projector needs to be positioned so that the objects hit by the beam of light are
at least 0,5 meters (1,64 ft) from the lens of the projector.
T 45°C
a
Max operating ambient temperature (Ta)
• Do not operate the xture if the ambient temperature (Ta) exceeds 45 °C (113 °F).
03PROLIGHTS - LumiPix XB050 / LumiPix XB100
T
-20°
C
aMinimum operating ambient temperature (Ta)
• Do not operate the xture if the ambient temperature (Ta) is below -20 °C (-4 °F).
Protection from burns and re
• The exterior of the xture becomes hot during use. Avoid contact by persons and
materials.
• Ensure that there is free and unobstructed airow around the xture.
• Keep ammable materials well away from the xture.
• Do not expose the front glass to sunlight or any other strong light source from any an-
gle. Lenses can focus the sun’s rays inside the xture, creating a potential re hazard.
• Do not attempt to bypass thermostatic switches or fuses.
IP65
Outdoor (temporary) use
• This product is rated with an IP (Ingress protection) for temporary outdoor use when
used and serviced according to the instruction contained in this document.
• Never use the xture in places subject to vibrations or bumps.
• Make certain that no inammable liquids, water or metal objects enter the xture.
• Excessive dust, smoke uid, and particle build up degrades performance, causes
overheating and will damage the xture.
• Damages caused by inadequate cleaning or maintenance are not covered by the
product warranty.
T
66°
C
c
Temperature of the external surface
• The surface of the xture can reach up to 66 °C (150 °F) during operation. Avoid
contact with people and materials.
Maintenance
• Warning! Disconnect the xture from AC mains power and allow to cool for at least
10 minutes before handling.
• Only technicians who are authorized by PROLIGHTS or Authorised service partners
are permitted to open the xture.
• Users may carry out external cleaning, following the warnings and instructions pro-
vided, but any service operation not described in this manual must be referred to a
qualied service technician.
• Important! Excessive dust, smoke uid, and particle build up degrades performance,
causes overheating and will damage the xture. Damages caused by inadequate
cleaning or maintenance is not covered by the product warranty.
Photobiological safety
• This device emits potentially dangerous optical radiation and is identied in the cat-
egory of Risk Group 2 according to EN 62471.
Do not stare at the operating light source
• Do not look directly at the LED source during operation. It can be harmful to the eyes
and skin.
• During Installation, operation and maintenance, be prepared for the xture to light
and move suddenly when connected to power.
• The LUMIPIXX050 should be positioned so that prolonged staring into the luminaire
at a distance closer than 10,50 m (34,45 ft) is not expected.
• The LUMIPIXX100 should be positioned so that prolonged staring into the luminaire
at a distance closer than 14,12 m (46,32 ft) is not expected.
PROLIGHTS - LumiPix XB050 / LumiPix XB10004
Minimun
distance
Risk
Group 2
Risk
Group 1
0.2 m
0.7 ft
10,50 m
34,45 ft
Minimun
distance
Risk
Group 2
Risk
Group 1
0.2 m
0.7 ft
14,12 m
46,32 ft
Disposal
• This product is supplied in compliance with European Directive 2012/19/EU – Waste
Electrical and Electronic Equipment. (WEEE). To preserve the environment please
dispose/ recycle this product at the end of its life according to the local regulation.
The products to which this manual refers comply with:
• 2014/35/EU - Safety of electrical equipment supplied at low voltage (LVD);
• 2014/30/EU - Electromagnetic Compatibility (EMC);
• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS);
• 2014/53/EU - Radio Equipment Directive (RED).
The products to which this manual refers comply with:
• UL 1573 + CSA C22.2 No. 166 - Stage and Studio Luminaires and Connector Strips.
• UL 1012 + CSA C22.2 No. 107.1 - Standard for power units other than class 2.
FCC Compliance:
• This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-
lowing two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesired operation.
Other approvals
• The product meets the safety requirements of the certification procedures of the
market in which it is placed and sold.
05PROLIGHTS - LumiPix XB050 / LumiPix XB100
1 - PACKAGING
PACKAGE CONTENT
• 1x LUMIPIXXB050 / LUMIPIXXB100.
• 1x 1,5 meters power cable (BARE END - SEETRONIC IP65 power connector).
• 2x side oor brackets.
• User Manual.
• 1 x OS27: quick-Lock omega bracket, M10 hole.
OPTIONAL ACCESSORIES
• FCLLUMIPIXXB: Flight case for 4 pcs LUMIPIXXB100 or 8 pcs LUMIPIXXB050.
• LPXB050BD: Barndoor to adjust the light beam for LUMIPIXXB050.
• LPXB050EC60: 60° egg crate for LUMIPIXXB050.
• LPXB050FILT20: light diffusion lter for LUMIPIXXB050, 20°.
• LPXB050FILT40: light diffusion lter for LUMIPIXXB050, 40°.
• LPXB050FILT60: light diffusion lter for LUMIPIXXB050, 60°.
• LPXB100BD: barndoor to adjust the light beam for LUMIPIXXB100.
• LPXB100EC60: 60° egg crate for LUMIPIXXB100.
• LPXB100FILT20: light diffusion lter for LUMIPIXXB100, 20°.
• LUMIPIXXB100: light diffusion lter for LUMIPIXXB100, 40°.
• LPXB100FILT60: light diffusion lter for LUMIPIXXB100, 60°.
• C6002A/B: slim aluminum clamp, 200kg loading, 48-51mm tubes, M10 bolt, silver/black.
• OS27: quick-Lock omega bracket, M10 hole.
• WSBBR512G5: blackBox R-512 G5 receiver 512Ch, 2.45GHz & 5.8GHz, DMX/RDM optional.
• WSBBF1G6: blackBox F-1 G6 transrec, 512ch, 2.45GHz, DMX&RDM,Bluetooth,G3,G4,G4S, G5, CRMX.
• WSBBF1G5: blackBox F-1 G5 transmitter, 2,45GHz & 5.2/5,8 GHz, DMX/RDM, 512Ch.
• TOUR53415L03: dmx cable HC5340. CANC5MXX XLR 5p->CANC5FXX XLR (f) 5p, L.3m.
• 958225L03: 3x2.5mm TH07 Cable, 16A 3p PwCon MXW, 16A 3p PwCon FXW, L. 3m.
• 9513FXWL03: ass. 3x2.5mm TH07 cable, 16A 3p 230V CEE plug, MENAC3FXW socket, L.3 m.
• 9533FXWL03: ass. 3x2.5mm TH07 cable, SHUKO plug, MENAC3FXW socket, L.3m.
• RSR0630A/B: steel security cable for hanging bodies, inox steel shackle, L=60 cm, silver/black.
• WSBBR512G6: blackBox R-512 G6 receiver 512Ch, 2.45GHz,DMX&RDM,Bluetooth,G3,G4,G4S,G5,CRMX.
• UPBOX1UP5: rmware uploader kit, USB IN, 5pin XLR DMX OUT, USB OUT.
Fig. 01
Weight: 7,5 kg - 16,53 lbs
Weight: 3,8 kg - 8,38 lbs
2 - TECHNICAL DRAWING
PROLIGHTS - LumiPix XB050 / LumiPix XB10006
Fig. 02
3 - INSTALLATION
MOUNTING
Check that the supporting structure can safely bear the weight of all installed xtures, clamps, cables,
auxiliary equipment, etc. and complies with locally applicable regulations.
When suspending the xture above ground level, secure it against failure of primary attachments by
attaching a safety wire that is approved as a safety attachment for the weight of the xture to an anchor
point on the product main frame.
Do not use removable parts or weak anchors for secondary attachment.
Warning! When clamping the xture to a truss or other structure at any angle, use clamps of half-cou-
pler type. Do not use any type of clamp that does not completely encircle the structure when fastened.
RSR0630A/B
Steel security cable
107 mm
4,21 in
07PROLIGHTS - LumiPix XB050 / LumiPix XB100
5 - START UP
CONNECT AND DISCONNECT POWER FROM THE PRODUCT
To apply and disconnect power to the product:
• Check that the product is installed and secured as indicated in the Safety Informations, and that
personal safety will not be put at risk when the xture lights up.
• Connect the power connector into the Mains input socket (100-240 VAC-50/60 Hz).
• The product is then ready for its operations and can be controlled through the available input sig-
nals on board.
• To disconnect power from the product, disconnect the Mains from the socket.
4 - CONNECTION TO THE MAINS SUPPLY
WARNING: For protection from electric shock, the xture must be earthed!
The product is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz
AC power source from 100-240 Volts.
If you need to install a power plug on the power cable to allow connection to power outlets, install a
grounding-type (earthed) plug, following the plug manufacturer’s instructions. If you have any doubts
about proper installation, consult a qualied electrician.
The max power consumption is 150W (LUMIPIXXB050) / 260W (LUMIPIXXB100).
Core (EU) Core (US) Connection Plug terminal marking
Brown Black Live L
Blue White Neutral N
Yellow+green Green Earth
PROLIGHTS - LumiPix XB050 / LumiPix XB10008
3
7
6
5
3
2
1
2
8
4
10
11
7
9
4
5
6 - PRODUCT OVERVIEW
1. USER INTERFACE with display and buttons for access to the control panel functions.
2. Holes to attach Quick-lock.
3. SAFETY EYE to attach safety cable.
4. GORE VALVE.
5. SIDE FLOOR BRACKETS.
6. DMX IN (5-p XLR): 1 = GND, 2 = sign-, 3 = sign+, 4 N/C, 5 N/C.
7. ETHERCON CONNECTORS IN / OUT signal.
8. POWER IN: for connection to the Mains 100-240V~/50-60Hz.
9. ANTENNA.
10.POWER OUT: power output for connection of multiple units in series.
11.DMX OUT (5-p XLR): 1 = GND, 2 = sign-, 3 = sign+, 4 N/C, 5 N/C.
Fig. 03
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere ProLights DJ-Equipment Handbücher
ProLights
ProLights POLAR500 Bedienungsanleitung
ProLights
ProLights LUMIPAR6UQ Bedienungsanleitung
ProLights
ProLights LUMIPAR12UQPRO Bedienungsanleitung
ProLights
ProLights 6BEAMQ Bedienungsanleitung
ProLights
ProLights PFZ715 Bedienungsanleitung
ProLights
ProLights PHYROBUB Bedienungsanleitung
ProLights
ProLights PHYRO600SNOW Bedienungsanleitung
ProLights
ProLights VERSAPAR PARLED ZOOM Bedienungsanleitung
ProLights
ProLights ASTROBEAM Bedienungsanleitung
ProLights
ProLights LUMIPAR7VWPRO Bedienungsanleitung
ProLights
ProLights TRUSSPOD3BAT Bedienungsanleitung
ProLights
ProLights EclProfile CT+ Bedienungsanleitung
ProLights
ProLights TRIBE LUMIPIX12UT Bedienungsanleitung
ProLights
ProLights SUNPIX24TRI Bedienungsanleitung
ProLights
ProLights GALLERYCLIPSETU Bedienungsanleitung
ProLights
ProLights PANORAMAIPWBX Bedienungsanleitung
ProLights
ProLights LEDPINSPOT Bedienungsanleitung
ProLights
ProLights SUNRISE2 Bedienungsanleitung
ProLights
ProLights PF5 Series Bedienungsanleitung
ProLights
ProLights SmartBat Wash Bedienungsanleitung
Beliebte DJ-Equipment Handbücher anderer Marken
thomann
thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung
Eagletone
Eagletone 6 Eyes Flower Bedienungsanleitung
EuroLite
EuroLite FLD-1508 Bedienungsanleitung
Technical Pro
Technical Pro LG8xSEA Bedienungsanleitung
JB Systems
JB Systems Lounge Laser DMX Bedienungsanleitung
Lightmaxx
Lightmaxx Vega Halo 90 Bedienungsanleitung
Elation
Elation FUZE WASH Z350 Bedienungsanleitung
Maverick
Maverick MK3 WASH Bedienungsanleitung
Infinity
Infinity TF-260C7 Fresnel Bedienungsanleitung
Chauvet
Chauvet EVE E-50Z Bedienungsanleitung
Eliminator Lighting
Eliminator Lighting E 138 Bedienungsanleitung
EuroLite
EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung