Radio Shack 900 MHz Digital Spread Spectrum Cordless Phone with Digital Answerer and Caller ID/Call Waiting... Bedienungsanleitung

Owner’s Manual

Please read before using this equipment.

900 MHz Digital Spread

Spectrum Cordless Phone

with Digital Answerer and Caller

ID/Call Waiting Deluxe

2Read This Before Installation

Read This Before Installation

We have designed your phone to conform to

federal regulations, and you can connect it to

most telephone lines. However, each device

you connect to the telephone line draws

power from the telephone line. We refer to

this power draw as the device's ringer equiv-

alence number, or REN on the bottom of

your phone.

If you use more than one phone or other de-

vice on the line, add up all of the RENs. If the

total is more than five (three in rural areas),

your telephones might not ring. If ringer oper-

ation is impaired, remove a device from the

line.

Important: Cordless phones such as this

one require AC power to operate. When the

AC power is off, you cannot dial out or re-

ceive incoming calls using your cordless

phone. For this reason, a cordless phone

should not be your only telephone. To be

safe, you should also have a phone that

does not require AC power to operate (not a

cordless phone) so you can still make and

receive calls if there is an AC power failure.

Some cordless phones operate at frequen-

cies that might cause interference to nearby

TVs and VCRs. To minimize or prevent such

interference, the base of the cordless phone

should not be placed near or on top of a TV

or VCR.

Your telephone operates on standard radio

frequencies as allocated by the FCC. Even

though the access protection code prevents

unauthorized use of your phone line, it is

possible for other radio units operating on

similar frequencies within a certain area to

unintentionally intercept your conversations

and/or cause interference. This lack of priva-

cy can occur with any cordless phone.

FCC STATEMENT

Your phone complies with Part 68 of

FCC

Rules

. You must, upon request, provide the

FCC registration number and the REN to

your telephone company. Both numbers are

the bottom of your phone.

Note: You must not connect your phone to:

• coin-operated systems

• party-line systems

• most electronic key telephone systems

WARNING: To reduce the risk of fire or

shock hazard, do not expose this product to rain

or moisture.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED PERSONNEL.

This symbol is intended to alert

you to the presence of uninsu-

lated dangerous voltage within

the product’s enclosure that might

be of sufficient magnitude to con-

stitute a risk of electric shock. Do

not open the product’s case.

This symbol is intended to inform

you that important operating and

maintenance instructions are

included in the literature accom-

panying this product.

RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.

Read This Before Installation

In the unlikely event that your phone causes

problems on the phone line, the phone com-

pany can temporarily discontinue your ser-

vice. If this happens, the phone company

attempts to notify you in advance. If advance

notice is not practical, the phone company

notifies you as soon as possible and advises

you of your right to file a complaint with the

FCC.

Also, the phone company can make changes

to its lines, equipment, operations, or proce-

dures that could affect the operation of this

telephone. The telephone company notifies

you of these changes in advance, so you can

take the necessary steps to prevent interrup-

tion of your telephone service.

Lightning

Your telephone has built-in protection circuits

to reduce the risk of damage from surges in

telephone line and power line current. These

protection circuits meet or exceed the FCC

requirements. However, lightning striking the

telephone or power lines can damage your

telephone.

Lightning damage is not common. Neverthe-

less, if you live in an area that has severe

electrical storms, we suggest that you unplug

your phone when storms approach to reduce

the possibility of damage.

IMPORTANT CALLER ID

INFORMATION

To use the system’s Caller ID and Call Wait-

ing features, you must be in an area where

those services are available and you must

subscribe to those services through your lo-

cal phone company.

Where Caller ID is offered, one or more op-

tions are generally available:

• caller’s number only

• caller’s name only

• caller’s name and number

IMPORTANT SAFETY

INSTRUCTIONS

When using your telephone equipment, ba-

sic safety precautions should always be fol-

lowed to reduce the risk of fire, electric

shock, and injury to persons, including the

following:

1. Read and understand all instructions.

2. Follow all warnings and instructions

marked on the product.

3. Never install telephone wiring during a

lightning storm.

4. Never install telephone jacks in wet

locations unless the jack is specifically

designed for wet locations.

5. Never touch uninstalled telephone wires

or terminals unless the telephone line

has been disconnected at the network

interface.

6. Use caution when installing or modifying

telephone lines.

7. Do not attach the AC power supply cord

to building surfaces with metal fittings (if

the product has an AC power cord).

8. Unplug this product from the wall outlet

before cleaning. Do not use liquid clean-

ers or aerosol cleaners. Use a damp

cloth for cleaning.

9. Do not use this product near water, for

example, near a bathtub, wash bowl,

kitchen sink, aquarium, or laundry tub, in

a wet basement, or near a swimming

pool.

10. Do not place this product on an unstable

cart, stand, or table. The product may

4Read This Before Installation

fall, causing serious damage to the

product.

11. Slots and openings in the cabinet and

the back or bottom are provided for ven-

tilation. To protect the product from over-

heating, these openings must not be

blocked or covered. The openings

should never be blocked by placing the

product on a bed, sofa, rug, or other

similar surface. This product should not

be placed in a built-in installation unless

proper ventilation is provided.

12. This product should never be placed

near or over a radiator or heat register.

13. This product should be operated only

from the type of power source indicated

on the marking label. If you are not sure

of the type of power supply to your

home, consult your local power com-

pany.

14. Do not allow anything to rest on the

power cord. Do not locate this product

where the cord will be stepped on.

15. Do not overload wall outlets and exten-

sion cords as this can result in a risk of

fire or electric shock.

16. Never push objects of any kind into this

product through cabinet slots as they

may touch dangerous voltage points or

short out parts that could result in a risk

of fire or electric shock. Never spill liquid

of any kind on the product.

17. To reduce the risk of electric shock, do

not disassemble this product. Take it to

a qualified serviceman when service or

repair work is required. Opening or

removing covers may expose you to

dangerous voltage or other risks. Incor-

rect reassembly can cause electric

shock when the product is subsequently

used.

18. Unplug this product from the wall outlet

and refer servicing to qualified service

personnel under the following condi-

tions:

• When the power cord plug is dam-

aged or frayed.

• If liquid has been spilled into the

product.

• If the product has been exposed to

rain or water.

• If the product does not operate nor-

mally by following the operating

instructions. Adjust only those con-

trols that are covered by the operat-

ing instructions because improper

adjustment of other controls may

result in damage and will often

require extensive work by a qualified

technician to restore the product to

normal operation.

• If the product has been dropped or

the cabinet has been damaged.

• If the product exhibits a distinct

change in performance.

19. Avoid using a telephone (other than a

cordless type) during an electrical storm.

There may be a remote risk of electric

shock from lightning.

20. Do not use the telephone to report a gas

leak in the vicinity of the leak.

BATTERY SAFETY

INSTRUCTIONS

Caution: To reduce the risk of fire or injury,

read and follow these instructions.

1. Use only the appropriate type and size

battery pack specified in the instruction

manual provided for this product.

Read This Before Installation

2. Do not dispose of the battery pack in a

fire. The cell may explode. Check with

local codes for possible special disposal

instructions.

3. Do not open or mutilate the battery

pack. Released electrolyte is corrosive

and may cause damage to the eyes or

skin. It may be toxic if swallowed.

4. Exercise care in handling the battery

pack in order not to short it with conduct-

ing materials such as rings, bracelets,

and keys. The battery or conductor may

overheat and cause burns.

5. Charge the battery pack provided with or

identified for use with this product only in

accordance with the instructions and

limitations specified in the instruction

manual provided for this product.

6. Observe proper polarity orientation

between the battery pack and battery

charger.

SAVE THESE

INSTRUCTIONS

6Contents

Contents

Features .................................................................................................................................. 8

Installation .............................................................................................................................. 9

Choosing a Location ............................................................................................................ 9

Mounting the System ........................................................................................................... 9

On a Desk ........................................................................................................................ 9

On a Wall Plate ................................................................................................................ 9

On a Wall ....................................................................................................................... 10

Connecting, Charging, and Replacing the Battery Pack .................................................... 10

Setting the Dialing Mode .................................................................................................... 11

Setting the Handset’s Ringer Tone/Volume ....................................................................... 12

Turning the Base’s Ringer On/Off ...................................................................................... 12

Setting Auto Talk ................................................................................................................ 12

Turning Caller ID/Call Waiting On/Off ................................................................................ 13

Storing Your Area Code ..................................................................................................... 13

Telephone Operation ............................................................................................................ 14

A Quick Look at the Handset ............................................................................................. 14

A Quick Look at the Base .................................................................................................. 15

Switching Between the Handset and the Speakerphone ................................................... 16

Using Both the Handset and the Speakerphone ................................................................ 16

Using a Headset ................................................................................................................ 16

Memory Dialing .................................................................................................................. 16

Storing a Name and Number in Memory ....................................................................... 16

Editing or Deleting a Number in Memory ....................................................................... 17

Entering a Pause ........................................................................................................... 18

Reviewing Memory Numbers ........................................................................................ 18

Dialing a Memory Number ............................................................................................. 18

Chain-Dialing Service Numbers .................................................................................... 18

Testing Stored Emergency Numbers ............................................................................. 18

Caller ID Operation ............................................................................................................... 19

Call Waiting Options Service .............................................................................................. 19

Using Call Waiting Options ............................................................................................ 19

Using Ask to Hold .......................................................................................................... 20

Using Conference .......................................................................................................... 20

Reviewing Caller ID Records ............................................................................................. 20

Caller ID Messages ....................................................................................................... 21

Adding/Deleting the Area Code ......................................................................................... 21

Dialing Numbers from Caller ID Records ........................................................................... 21

Storing a Caller ID Number in Memory .............................................................................. 21

Deleting Caller ID Records ................................................................................................ 21

Answering System Operation ............................................................................................. 23

Using the Menu Button ...................................................................................................... 23

Setting the Day and Time ................................................................................................... 23

Setting the Number of Rings .............................................................................................. 23

Contents

Setting the Record Time .................................................................................................... 24

Selecting the Outgoing Message ...................................................................................... 24

Recording/Deleting an Outgoing Message ................................................................... 24

Setting the TAD to Answer Calls ....................................................................................... 25

Screening Calls ................................................................................................................. 25

Recording Incoming Messages ......................................................................................... 25

Using the Mail Boxes ......................................................................................................... 25

Recording a Memo ............................................................................................................ 26

Recording a Conversation ................................................................................................. 26

Playing Messages ............................................................................................................. 26

Adjusting the TAD’s Volume .............................................................................................. 27

Deleting Messages ............................................................................................................ 27

Remote Operation ............................................................................................................. 27

Setting the Security Code ............................................................................................. 27

Using the Toll-Saver ...................................................................................................... 27

Using Remote Commands ............................................................................................ 28

Playing Back the Messages .......................................................................................... 28

Deleting All the Messages in a Mail Box ....................................................................... 28

Setting the TAD to Answer Calls ................................................................................... 29

Setting the TAD Not to Answer Calls ............................................................................ 29

Recording a Memo ........................................................................................................ 29

Recording a New Outgoing Message ........................................................................... 29

Listening to the Help Guide ........................................................................................... 29

Troubleshooting ................................................................................................................... 30

Care ................................................................................................................................... 31

8Features

Features

Your RadioShack 900 MHz Digital Spread

Spectrum Cordless Phone uses advanced

technology for superior audio quality and ex-

tended range. Caller ID records each caller’s

telephone number (and name, if available in

your area) and the date and time of the call,

as provided by your local phone company to

Caller ID service subscribers.

If you subscribe to Call Waiting and Caller

ID, the phone can show you the incoming

caller information, even when you are al-

ready talking on the phone.

The phone’s features include:

Spread Spectrum Technology — spreads

the signal across several frequencies, pro-

viding additional security for your phone con-

versations.

Caller ID/Call Waiting Deluxe — gives you

several options for handling waiting callers

(you must subscribe to the Call Waiting Op-

tions Service through your phone company

to use this feature).

20 Number Memory Dialing — lets you

store up to 20 numbers in memory for easy

dialing.

Headset Jack — for optional hands-free use

with a headset (available at your local

RadioShack store).

Security Access-Protection Code — helps

prevent other cordless phone users from us-

ing your phone line while the handset is off

the base.

3-Number Redial — lets you quickly redial

any of the last three numbers dialed.

Auto Talk — you can set the phone so you

can answer a call simply by lifting the hand-

set from the base.

Any-Key Answer — you can set the phone

so you can press any key to answer a call

when the handset is away from the base.

Hearing-Aid Compatibility — lets you use

your phone with hearing aids that have a T

(telephone) switch.

The Telephone Answering Device (TAD)

stores up to 20 minutes of messages on a

computer chip and records each message’s

day and time. This gives you advanced ca-

pabilities over tape-based answering ma-

chines:

• You can delete individual messages and

save the rest.

• There are no tapes to bother with and no

tape mechanisms to wear out.

The remote operation feature lets you oper-

ate your TAD from a touch-tone phone or

from a rotary phone with a pocket tone dialer.

The TAD’s features include:

Phone Pick-Up Detection — stops record-

ing when you pick up any phone on the same

line as the TAD, and resets to answer the

next call.

Voice-Prompted Menu Setting — lets you

set the TAD’s various functions through the

voice guidance.

Programmable Security Code — you can

set a two-digit security code to secure re-

mote operation.

3 Mail Boxes — you can select a mail box

so you can record your message from re-

mote location.

Installation

CHOOSING A LOCATION

You can place the phone’s base on a desk or

table, or mount it on a standard wall plate or

directly on a wall. Choose a location that is:

• near an AC outlet

• near a modular telephone line jack

• out of the way of normal activities

• away from electrical machinery, electri-

cal appliances, metal walls or filing cabi-

nets, wireless intercoms, alarms, and

room monitors

• away from other cordless phones

The base’s location affects the phone’s

range. If you have a choice of several loca-

tions, try each to see which provides the best

performance.

Cautions:

You must use a Class 2 power

source that supplies 9V DC

and delivers at least 350 mA.

Its center tip must be set to positive and

its plug must fit the phone’s DC IN 9V

jack. The supplied adapter meets these

specifications. Using an adapter that

does not meet these specifications

could damage the phone or the adapter.

• Always connect the AC adapter to the

phone before you connect it to AC

power. When you finish, disconnect the

adapter from AC power before you dis-

connect it from the phone.

Your telephone connects directly to a modu-

lar telephone line jack. If your telephone wir-

ing does not have a modular jack, you can

update the wiring yourself using jacks and

adapters (available at your local RadioShack

store), or have the telephone company up-

date the wiring for you. You must use com-

patible modular jacks that are compliant with

Part 68 of

FCC Rules

Note: The USOC number of the jack to be

installed is RJ11C (or RJ11W for a wall plate

jack).

MOUNTING THE SYSTEM

On a Desk

1. Plug one end of the supplied long modu-

lar cord into the base’s TEL LINE jack.

2. Insert the supplied AC adapter’s barrel

plug into the base’s DC IN 9V jack.

3. Route the adapter’s cord through the

strain relief slot on the base.

4. Plug the modular cord’s other end into

the phone jack.

5. Plug the adapter into a standard AC out-

let.

6. Lift the base’s antenna to a vertical posi-

tion.

On a Wall Plate

1. Plug one end of the supplied short mod-

ular cord into the base’s TEL LINE jack.

2. Insert the supplied AC adapter’s barrel

plug into the base’s DC IN 9V jack.

3. Route the AC adapter and modular

cords through the grooves on the base.

4. Plug the modular cord’s other end into

the wall plate jack, then align the base’s

10 Installation

keyhole slots with the wall plate studs

and slide the base down to secure it.

5. Plug the adapter into a standard AC out-

let.

6. Lift the base’s antenna to a vertical posi-

tion.

On a Wall

To mount the TAD directly on a wall, you

need two screws of at least 13/8inch long

(not supplied) with heads that fit into the key-

hole slots on the bottom of the base.

1. Drill two holes 315/16 inches (100 mm)

apart. Then thread a screw into each

hole, letting the heads extend about 1/8

inch (3 mm) from the wall.

2. Plug one end of the supplied long modu-

lar cord into the base’s TEL LINE jack.

3. Insert the supplied AC adapter’s barrel

plug into the base’s DC IN 9V jack.

4. Route the adapter cable and modular

cords through the grooves on the base.

5. Align the base’s keyhole slots with the

mounting screws and slide the base

down to secure it.

6. Plug the modular cord’s other end into

the phone jack.

7. Plug the adapter into a standard AC out-

let.

8. Lift the base’s antenna to a vertical posi-

tion.

CONNECTING, CHARGING,

AND REPLACING THE

BATTERY PACK

The phone comes with a rechargeable

nickel-cadmium battery pack in the hand-

set. Before using your phone, you must

connect the battery pack, then charge it for

about 24 hours.

1. Press down and slide off the battery

pack compartment cover.

2. Lift the battery pack out of the compart-

ment.

3. Plug the battery pack's connector into

the socket in the compartment, (the con-

nector fits only one way), replace the

battery pack, and replace the cover.

To charge the battery pack, place the hand-

set either faceup or facedown on the base.

The CHARGE/IN USE indicator on the base

lights.

Note: Be sure the battery pack is properly

connected before you try to charge it. The

CHARGE/IN USE indicator lights when the

handset is on the base even if the battery

pack is not properly connected.

Recharge the battery pack when Bemý8Wjj[ho

Bemý8Wjj[hoBemý8Wjj[ho

Bemý8Wjj[ho

flashes on the display.

Notes:

• When you first use the phone after

charging or recharging the battery pack,

the phone might not work and you might

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Radio Shack Schnurloses Telefon Handbücher

Radio Shack

Radio Shack ET-1106 Bedienungsanleitung

Radio Shack

Radio Shack 43-3585 Bedienungsanleitung

Radio Shack

Radio Shack TAD-1015 Bedienungsanleitung

Radio Shack

Radio Shack ET-551 Bedienungsanleitung

Radio Shack

Radio Shack ET-1118 Bedienungsanleitung

Radio Shack

Radio Shack 2.4 GHz Digital Spread Spectrum Cordless Telephone with Caller ID/Call Waiting... Bedienungsanleitung

Radio Shack

Radio Shack 43-3815/43-3898 Bedienungsanleitung

Radio Shack

Radio Shack ET-539 Bedienungsanleitung

Radio Shack

Radio Shack ET-1110 Bedienungsanleitung

Radio Shack

Radio Shack 43-3526 Bedienungsanleitung

Radio Shack

Radio Shack 900 MHz Digital Spread Spectrum Cordless Phone with Dual Caller... Bedienungsanleitung

Radio Shack

Radio Shack TAD-268 Bedienungsanleitung

Radio Shack

Radio Shack 43-3571 Bedienungsanleitung

Radio Shack

Radio Shack TAD-734 Bedienungsanleitung

Radio Shack

Radio Shack Presidian Bedienungsanleitung

Radio Shack

Radio Shack ET-545 Bedienungsanleitung

Radio Shack

Radio Shack 43-1088 Bedienungsanleitung

Radio Shack

Radio Shack 43-3546 Bedienungsanleitung

Radio Shack

Radio Shack TAD-728 Bedienungsanleitung

Radio Shack

Radio Shack 43-143 Bedienungsanleitung

Radio Shack

Radio Shack Cordless Phone Bedienungsanleitung

Radio Shack

Radio Shack 43-683 Bedienungsanleitung

Radio Shack

Radio Shack TAD-727 Bedienungsanleitung

Radio Shack

Radio Shack ET-550 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung