Radio Shack ET-1112 Bedienungsanleitung

Cat. No. 43-1112

OWNER’S MANUAL

Please read before using this equipment.

ET-1112

900 MHz Digital Spread Spectrum

Cordless Phone

43-1112.fm Page 1 Monday, September 13, 1999 5:08 PM

FEATURES

Your RadioShack ET-1112 900 MHz

Digital Spread Spectrum Cordless Tele-

phone uses advanced cordless tele-

phone technology to give you superior

audio quality and extended range.

And, the ET-1112’s headset jack means

you can connect an optional headset for

hands-free convenience.

The ET-1112 has these features:

Spread Spectrum Technology —

spreads the signal across several fre-

quencies, providing additional security

for your phone conversations.

900 MHz — provides less interference,

clearer sound, and more than twice the

range of 46/49 MHz cordless phones.

20-Number Memory Dialing — lets you

store 20 numbers in memory for easy di-

aling.

Speed Dial — you can store three num-

bers in the ET-1112’s speed dial memo-

ry, then dial them with the touch of a

button.

Page — lets you send a signal from the

base to the handset to page someone or

to help you locate the handset if you

have misplaced it.

Volume Control — lets you adjust the

volume you hear through the handset.

Programmable Ringer — choose from

eight tone/volume settings for the hand-

set’s ringer.

Ample Talk and Standby Time — the

supplied battery (when fully charged)

provides about 3.5 hours of talk time or

7 days of standby time.

Security Access-Protection Code —

prevents other cordless phone users

from using your phone line while the

handset is off the base.

Redial — lets you quickly dial the last

number dialed.

Flash — sends an electronic switch-

hook signal for use with special phone

services, such as Call Waiting.

Tone or Pulse Dialing — lets you use

your phone with tone or pulse (rotary) di-

aling and lets you switch from pulse to

tone dialing for long-distance, bank-by-

phone, or other special services.

Hearing-Aid Compatibility — lets you

use your phone with hearing aids that

have T (telephone) switch.

This telephone has been tested and

found to comply with all applicable UL

and FCC standards.

RadioShack is a registered trademark used by Tandy Corporation.

43-1112.fm Page 2 Monday, September 13, 1999 5:08 PM

Important:

• Cordless phones such as this one

require AC power to operate. When

the AC power is off, you cannot dial

out or receive incoming calls using

your ET-1112. To be safe, you

should also have a phone that does

not need AC power to operate (not a

cordless phone) so you can still

make and receive calls if there is an

AC power failure.

• When AC power is lost, the ET-1112

loses the security access-protection

code connection between the base

and the handset. When power is

restored, put the handset on the

base briefly to restore this connec-

tion so you can use the handset.

READ THIS BEFORE

INSTALLATION

We have designed your phone to con-

form to federal regulations and you can

connect it to most phone lines. However,

each device that you connect to the tele-

phone line draws power from the line.

We refer to this power draw as the

phone’s ringer equivalence number, or

REN. The REN is on the bottom of your

phone.

If you use more than one phone or other

device on the line, add up all the RENs.

If the total is more than five (three in ru-

ral areas), your phones might not ring. If

ringer operation is impaired, remove one

of the devices from the line.

WARNING: To reduce the risk of fire or

shock hazard, do not expose this product to rain

or moisture.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED PERSONNEL.

This symbol is intended to alert

you to the presence of uninsu-

lated dangerous voltage within

the product’s enclosure that might

be of sufficient magnitude to con-

stitute a risk of electric shock. Do

not open the product’s case.

This symbol is intended to inform

you that important operating and

maintenance instructions are

included in the literature accom-

panying this product.

43-1112.fm Page 3 Monday, September 13, 1999 5:08 PM

FCC STATEMENT

Your telephone complies with Part 68 of

FCC Rules

. Upon request, you must

provide the phone’s FCC registration

number and REN to your telephone

company. These numbers are on the

bottom of the base.

Note: You must not connect your tele-

phone to:

• coin-operated systems

• party-line systems

• most electronic key phone systems

43-1112.fm Page 4 Monday, September 13, 1999 5:08 PM

INSTALLATION

SELECTING A LOCATION

You can place the phone’s base on a

desk top or table, or mount it on a wall.

Select a location that is:

• near an accessible AC outlet

• near a telephone line jack

• out of the way of normal activities

• away from electrical machinery,

electrical appliances, metal walls or

filing cabinets, wireless intercoms,

alarms, and room monitors

• away from other cordless phones

The base’s location affects the hand-

set’s range. If you have a choice of sev-

eral locations, try each to see which

provides the best performance.

Caution: The supplied RadioShack AC

adapter was designed specifically for

your ET-1112. Use only the supplied

adapter.

On a Desk Top

Follow these steps when you place the

base on a desk, shelf, or table.

1. Plug one end of the supplied long

modular cord into the TEL LINE jack

on the back of the base.

2. Plug the modular cord’s other end

into a modular phone line jack.

3. Insert the supplied AC adapter’s

barrel plug into the DC IN 9V jack on

the back of the base.

4. Route the adapter’s cord through

the strain relief slot on the base.

5. Plug the adapter into a standard AC

outlet.

6. Lift the base’s antenna to an upright

position.

On a Wall Plate or Wall

1. Plug one end of the supplied short

modular cord into the TEL LINE jack

on the back of the base as in “On a

Desk Top,” Step 1.

2. Insert the supplied AC adapter’s

barrel plug into the DC IN 9V jack as

in “On a Desk Top,” Step 3.

43-1112.fm Page 5 Monday, September 13, 1999 5:08 PM

3. Route the adapter and modular

cords through the grooves on the

bottom of the base.

4. Plug the modular cord’s other end

into the wall plate jack, then align

the base’s keyhole slots with the

wall plate studs and slide the base

downward to secure it.

5. Plug the adapter into a standard AC

outlet.

6. Press and lift out the handset

holder, rotate it 180°, then snap it

back into place so it holds the hand-

set.

7. Lift the base’s antenna to an upright

position.

Note: To mount the ET-1112 directly on

a wall, you need two screws (not sup-

plied) with heads that fit into the keyhole

slots on the bottom of the base.

Follow the steps under “On a Wall Plate

or Wall” on Page 5, then apply these ad-

ditional instructions for placement on a

wall.

1. Drill two holes 315/16

inches (100 mm)

apart. Then thread

a screw into each

hole, letting the

heads extend about

5/16 inch (8 mm)

from the wall.

2. Plug one end of the supplied long

modular cord into the TEL LINE jack

on the back of the base.

3. Align the base’s keyhole slots with

the mounting screws and slide the

base downward to secure it.

Handset

Holder

5/16

Inch

315/16

Inch

43-1112.fm Page 6 Monday, September 13, 1999 5:08 PM

CONNECTING AND

CHARGINGTHEBATTERY

PACK

The phone comes with a rechargeable

nickel-cadmium battery pack in the

handset, but not connected. Before us-

ing your phone, you must connect the

battery pack and then charge it for about

24 hours.

1. Press down and slide the battery

compartment cover in the direction

of the arrow to remove it.

2. Unfasten the battery retainer strap

and lift the battery pack out of the

compartment. Plug the battery

pack’s connector into the socket in

the compartment. The connector fits

only one way.

3. Put the battery pack in the compart-

ment and fasten the battery retainer

strap.

4. Replace the cover.

To charge the battery pack, simply place

the handset on the base. The CHARGE/

IN USE indicator on the base lights.

Recharge the battery pack when the

handset beeps and the TALK/BATT indi-

cator flashes.

Important: Be sure the battery pack is

properly connected before you try to

charge it. The CHARGE/INUSE indica-

tor lights when the handset is on the

base, even if the battery pack is not con-

nected.

Notes:

• When you first use the phone after

charging or recharging the battery

pack, the phone might not work and

you might hear an error tone. If this

happens, return the handset to the

base for a few seconds.

• About once a month, fully discharge

the battery pack by keeping the

handset off the base until the TALK/

BATT indicator flashes. Otherwise,

the battery pack loses its ability to

fully recharge.

43-1112.fm Page 7 Monday, September 13, 1999 5:08 PM

• Using a pencil eraser, clean the

charging contacts on the handset

and the base about once a month.

• If the TALK/BATT indicator does not

light and the phone does not work,

recharge the battery pack. (The bat-

tery power might be too low to light

the indicator.)

• If the battery pack becomes weak

during a call, you hear a beep and

the TALK/BATT indicator flashes

every 4 seconds. Recharge the bat-

tery pack.

• If the battery pack is completely dis-

charged, the handset loses the

security access-protection code. To

reset the code, place the handset on

the base and charge the battery

pack.

• The supplied battery pack should

last for about a year. When the bat-

tery pack loses its ability to fully

recharge, order a replacement bat-

tery pack from your local

RadioShack store (see “Replacing

the Battery Pack” on Page 18).

SETTING THE DIALING

MODE

Set PULSE-TONE on the back of the

base for the type of service you have. If

you are not sure which type you have,

once the battery pack is fully charged,

do this test.

1. Be sure PULSE-TONE is set to TONE.

2. Lift the handset, press TALK, and lis-

ten for a dial tone.

3. Press any number other than 0.

Note: If your phone system requires

that you dial an access code (9, for

example) before you dial an outside

number, do not press the access

code either.

If the dial tone stops, you have

touch-tone service. Leave PULSE-

TONE set to TONE.

If the dial tone continues, you have

pulse service. Set PULSE-TONE to

PULSE.

43-1112.fm Page 8 Monday, September 13, 1999 5:08 PM

SETTING THE RINGER’S

TONE AND VOLUME

You can set four ringer tones and a high

and low volume for each.

To change the tone, lift the handset and

press FLASH. Then, enter the ringer

tone number (1–4) using the number

keys. The selected tone sounds briefly.

To hear and change the ringer volume

setting, press or .

FLASH

43-1112.fm Page 9 Monday, September 13, 1999 5:08 PM

OPERATION

MAKING AND RECEIVING

CALLS

To make a call, lift the handset and

press

TALK. The TALK indicator on the

handset and the IN USE indicator on the

base light. When you hear a dial tone,

dial the number.

To answer a call, lift the handset if nec-

essary then press TALK.

The ET-1112 scans 20 channels (fre-

quency pairs used between the base

and the handset) and automatically se-

lects a clear channel each time you

make or receive a call.

Note: If the handset is too far from the

base, the channel might not be clear.

Move closer to the base and try making

the call again.

To end a call, place the handset on the

base or press TALK.

Note: If you press TALK to hang up and

the phone does not disconnect, press

TALK again while holding the handset

closer to the base, or place the handset

on the base.

SETTING THE HANDSET

VOLUME

You can choose one of four volume set-

tings — low, medium, high, or maximum

— for the handset. To change the vol-

ume, press or during a call.

USING REDIAL

You can quickly dial the last number di-

aled. When you hear a dial tone, simply

press REDIAL.

Notes:

• The redial memory holds up to 32

digits, so you can redial long-dis-

tance as well as local numbers.

• The redial memory also holds pause

entries. See “Entering a Pause” on

Page 13.

USING MUTE

To talk to someone in the room without

the person on the other end of the

phone line hearing your conversation,

press MUTE. The TALK/BATT indicator

flashes.

TALK

REDIAL MUTE

43-1112.fm Page 10 Monday, September 13, 1999 5:08 PM

Inhaltsverzeichnis

Andere Radio Shack Schnurloses Telefon Handbücher

Radio Shack

Radio Shack ET-916 Bedienungsanleitung

Radio Shack

Radio Shack 43-142 Bedienungsanleitung

Radio Shack

Radio Shack 43-3704 Bedienungsanleitung

Radio Shack

Radio Shack 2-Line 900 MHz Handsfree Cordless Phone Bedienungsanleitung

Radio Shack

Radio Shack 43-3526 Bedienungsanleitung

Radio Shack

Radio Shack Cordless Phone Bedienungsanleitung

Radio Shack

Radio Shack Sprint SP-514 Bedienungsanleitung

Radio Shack

Radio Shack 43-3817 Bedienungsanleitung

Radio Shack

Radio Shack Caller ID System 1500 Bedienungsanleitung

Radio Shack

Radio Shack Big-Button Caller ID Trim Fone 43-3904 Bedienungsanleitung

Radio Shack

Radio Shack Digital Spread Spectrum Cordless Telephone with Digital Answering... Bedienungsanleitung

Radio Shack

Radio Shack ET-917 Bedienungsanleitung

Radio Shack

Radio Shack Wireless Phone Jack System Bedienungsanleitung

Radio Shack

Radio Shack 43-3812 Bedienungsanleitung

Radio Shack

Radio Shack 43-3557 Bedienungsanleitung

Radio Shack

Radio Shack 43-325 Bedienungsanleitung

Radio Shack

Radio Shack ET-1101 Bedienungsanleitung

Radio Shack

Radio Shack Digital Answering System with Caller ID Deluxe and 2.4 GHz Digital Spread Spectrum Cordless... Bedienungsanleitung

Radio Shack

Radio Shack 43-3575 Bedienungsanleitung

Radio Shack

Radio Shack 43-3535 Bedienungsanleitung

Radio Shack

Radio Shack ET-1106 Bedienungsanleitung

Radio Shack

Radio Shack ET-539 Bedienungsanleitung

Radio Shack

Radio Shack 43-3548 Bedienungsanleitung

Radio Shack

Radio Shack 43-324 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung