Radio Shack ET-518 Bedienungsanleitung

Cat. No. 43-1018

OWNER’S MANUAL

Cordless Telephone

Please read before using this equipment.

ET-518

with 9-Memory Speed-Dialing

43-1018.fm Page 1 Tuesday, August 17, 1999 8:53 AM

FEATURES

Radio Shack is a registered trademark used by Tandy Corporation.

Your Radio Shack ET-518 Cordless

Telephone with 9-Memory Speed Dial-

ing offers the latest advances in cord-

less phone technology. It includes the

following features:

Advanced Super CCT Circuitr

—

provides clarity comparable to a cord-

ed phone, reduces background noise,

and increases effective operating dis-

tance.

Automatic Securit

Access Code —

changes each time you return the

handset to the cradle to help prevent

other cordless phone users from using

your phone line while the handset is off

the cradle.

COM-LOK®— ensures that other

cordless phone users cannot use your

phone line while the handset is on the

cradle.

9-Number Memor

Dialin

— lets

you store nine phone numbers in

memory for easy dialing.

Flash — sends an electronic switch-

hook signal for use with special phone

services such as call waiting.

Touch Tone or Pulse (Rotar

) Dial-

— lets you connect your phone to

either type of service.

Redial — quickly redials the last num-

ber dialed with the touch of a button.

Note: Your phone comes with a bat-

tery, which you must install, connect,

and charge before you use your phone

for the first time.

Important: Cordless phones such as

this one require AC power to operate.

When the AC power is off, you cannot

dial out or receive incoming calls using

your cordless phone. For this reason,

this cordless phone should not be your

only telephone. To be safe, you should

also have a phone that does not need

AC power to operate (not a cordless

phone) so you can still make and re-

ceive calls if there is an AC power fail-

ure.

For your records, we urge you to

record the serial number of your phone

in the space below. The serial number

is located on the bottom panel of the

base.

Serial Number: __________________

This telephone has been tested and

found to comply with all applicable UL

and FCC standards.

Your cordless telephone operates on

standard radio frequencies, as allocat-

ed by the FCC. Therefore, it is possible

for other radio units operating on simi-

43-1018.fm Page 2 Tuesday, August 17, 1999 8:53 AM

lar frequencies, within a certain area,

to inadvertently intercept your conver-

sations and/or cause interference on-

your cordless telephone. This lack of

privacy can occur with any cordless

telephone.

However, your cordless phone is avail-

able in four different factory-set fre-

quencies. If you have problems with

interference, you can exchange your

phone within 30 days of purchase for

one that uses a different frequency.

Warning: To prevent fire or shock haz-

ard, do not expose this product to rain

or moisture.

This symbol is intended to alert you

to the presence of uninsulated dan-

gerous voltage within the product’s

enclosure that might be of sufficient

magnitude to constitute a risk of

electric shock. Do not open the

product’s case.

This symbol is intended to inform

you that important operating and

maintenance instructions are in-

cluded in the literature accompany-

ing this product.

READ THIS BEFORE

INSTALLATION

We have designed your phone to con-

form to federal regulations, and you

can connect it to most phone lines.

However, each device that you con-

nect to the phone line draws power

from the line. We refer to this power

draw as the device’s

ringer equiva-

lence number

, or REN. The REN is

shown on the bottom of your phone.

If you are using more than one phone

or other device on the line, add up all

the RENs. If the total is more than five,

your phone might not ring. In rural ar-

eas, a total REN of three might impair

ringer operation. If ringer operation is

impaired, remove a device from the

line.

FCC STATEMENT

This telephone complies with Part 68

FCC Rules

. You must, upon re-

quest, provide the FCC Registration

Number and the REN to your phone

company. These numbers are located

on the bottom of your phone.

Note: You must not connect your

phone to any of the following.

• Coin-operated systems

• Party-line systems

• Most electronic key phone sys-

tems

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVIC-

ING TO QUALIFIED PERSONNEL.

CAUTION !

43-1018.fm Page 3 Tuesday, August 17, 1999 8:53 AM

TABLE OF CONTENTS

Installation ............................................................................................................ 5

Selecting a Mounting Location ........................................................................ 5

Placing the Base on a Desktop ................................................................. 5

Mounting the Base on a Wall Plate ........................................................... 6

Mounting the Base Directly on the Wall .................................................... 8

Preparation ......................................................................................................... 10

Installing the Handset Battery ........................................................................ 10

Charging the Handset Battery ........................................................................10

Setting the Dialing Mode ............................................................................... 11

Operation ............................................................................................................ 12

Making/Answering a Call ............................................................................... 12

Using the Handset at the Base ............................................................... 12

Using the Handset away from the Base .................................................. 12

Using Redial .................................................................................................. 13

Using Flash .................................................................................................... 13

Using Tone Services on a Pulse Line ............................................................ 13

Using Page .................................................................................................... 14

Memory Dialing .............................................................................................. 14

Storing a Number in Memory .................................................................. 14

Entering a Pause in a Memory Number .................................................. 15

Dialing a Stored Number ......................................................................... 16

Storing/Chain Dialing Special Service Numbers ..................................... 16

Testing Stored Emergency Numbers ...................................................... 16

Troubleshootin

................................................................................................. 17

Care And Maintenance ...................................................................................... 19

Replacing the Battery .....................................................................................20

The FCC Wants You to Know ........................................................................ 20

Lightning ........................................................................................................ 21

43-1018.fm Page 4 Tuesday, August 17, 1999 8:53 AM

INSTALLATION

SELECTING A

MOUNTING LOCATION

You can mount the base on a wall

plate or directly on a wall. Or, you can

place it on a desk, shelf, or table. Se-

lect a location that is:

• Near an AC outlet

• Near a telephone line jack

• Out of the way of normal activities

• Away from computers, remote

control toys, wireless micro-

phones, wireless intercoms,

alarms and room monitors, fluo-

rescent lights, electrical machin-

ery, electrical appliances, metal

walls, filing cabinets, and other

large metal objects

For the best reception, you should be

able to fully extend the base’s antenna

and place it in a vertical position.

The base’s location affects the phone’s

range. If you have a choice of several

locations, try each to see which one

provides the best performance.

If the phone line jack is not a modular

jack, you must update the wiring your-

self, using jacks and adapters avail-

able at your local Radio Shack store.

Or, you can let the phone company up-

date the wiring for you.

• The phone company will charge

you for the installation of the nec-

essary jacks.

• The USOC number of the jack to

be installed is RJ11C for a base-

board jack and RJ11W for a wall-

plate jack.

Placing the Base on a

Desktop

Follow these steps to place the base

on a desk, shelf, or table.

1. Plug one end of the supplied mod-

ular cord into the PHONE jack on

the back of the base.

2. Plug the modular cord’s other end

into a modular phone line jack.

3. Insert the supplied AC adapter’s

barrel plug into the 12V DC jack on

the back of the base.

43-1018.fm Page 5 Tuesday, August 17, 1999 8:53 AM

4. Plug the adapter into a standard

AC outlet.

Caution: You must use a 120V AC/

12V DC adapter that delivers at least

200 milliamps. Its plug must correctly

fit the phone’s 12V DC jack. The sup-

plied adapter meets these require-

ments. Using an adapter that does not

meet these requirements could dam-

age the phone or the adapter.

Mounting the Base on a Wall

Plate

You need a short modular cord (such

as Cat. No. 279-390, not supplied) and

a standard wall plate (Cat. No. 279-

382, not supplied), for this mounting

method.

1. Plug one end of the short modular

cord into the PHONE jack on the

back of the base.

2. Route the short cord downward

through the top left slot on the

base’s bottom and under the clips

as shown.

3. Route the other end of the short

cord through the hole in the

bracket’s center.

4. To attach the supplied bracket to

the bottom of the base, insert the

tabs on the bracket into the slots

on the base, then slide the bracket

up.

43-1018.fm Page 6 Tuesday, August 17, 1999 8:53 AM

5. nsert the supplied AC adapter’s

barrel plug into the 12V DC jack on

the back of the base. Then route

the adapter’s cord through the

right slot on the base’s bottom and

under the clips as shown. Plug the

adapter into a standard AC outlet.

6. Plug the short modular cord into

the wall plate’s jack.

7. Align the bracket’s keyhole slots

with the wall plate studs and slide

the base downward to secure it.

8. Press and lift out the handset

holder. Rotate the holder 180°as

shown, and then snap it back into

place so it holds the handset.

Note: If you later want to mount the

base on a desktop, press PUSH and

slide the bracket down to remove it

from the base’s bottom.

43-1018.fm Page 7 Tuesday, August 17, 1999 8:53 AM

Mounting the Base Directly

on the Wall

You need two wood screws (not sup-

plied) for this mounting method.

1. Drill two holes 315/16 inches apart.

Then thread a screw into each

hole, letting the heads extend 1/4

inch from the wall.

2. Plug one end of the supplied mod-

ular cord into the PHONE jack on

the back of the base.

3. On the bottom of the base, route

the modular cord downward and

under the left slot’s clips as

shown.

4. To attach the supplied bracket to

the bottom of the base, insert the

tabs on the bracket into the slots

on the base, then slide the bracket

up.

43-1018.fm Page 8 Tuesday, August 17, 1999 8:53 AM

5. Insert the supplied AC adapter’s

barrel plug into the 12V DC jack on

the back of the base. Then route

the adapter’s cord through the

right slot on the base’s bottom and

under the clips. Plug the adapter

into a standard AC outlet.

6. Plug the modular cord into a mod-

ular phone line jack.

7. Align the keyhole slots with the

mounting screws and slide the

base downward to secure it.

8. Press and lift out the handset

holder. Rotate the holder 180°as

shown, and then snap it back into

place so it holds the handset.

Note: If you later want to mount the

base on a desktop, press PUSH and

slide the bracket down to remove it

from the base’s bottom.

43-1018.fm Page 9 Tuesday, August 17, 1999 8:53 AM

PREPARATION

INSTALLING THE

HANDSET BATTERY

Your phone comes with a battery

which you must install, connect, and

charge for 15 hours before you use

your phone for the first time.

To install the battery:

1. Slide off the battery compartment

cover.

2. Insert the battery into the compart-

ment so its connector can reach

the pins inside the compartment,

and secure it with the plastic

strap.

3. Slide the battery’s connector onto

the pins.

Caution: The connector only fits

one way; do not force it. If you

have difficulty sliding the connec-

tor onto the pins, turn it over and

try again.

4. Replace the cover, then follow the

instructions under “Charging the

Handset Battery’’ before you use

the phone.

CHARGING THE

HANDSET BATTERY

When you install a new battery, set

POWER to OFF. Then place the hand-

set on the cradle so the IN USE/

CHARGE indicator lights and charge

the battery for about 15 hours.

Recharge the battery when LOW

BATT on the handset lights.

Caution: To avoid damage to the bat-

tery, always recharge the handset bat-

tery as soon as LOW BATT lights.

Notes:

• You can set POWER to ON while

the battery charges, but it charges

more quickly if you set POWER to

OFF.

• If the IN USE/CHARGE indicator

does not light when you place the

handset on the cradle, be sure the

battery is connected to the pins

inside the battery compartment,

and the AC adapter is securely

connected to the base. Also,

check the charging contacts on

43-1018.fm Page 10 Tuesday, August 17, 1999 8:53 AM

Inhaltsverzeichnis

Andere Radio Shack Schnurloses Telefon Handbücher

Radio Shack

Radio Shack ET-596 Bedienungsanleitung

Radio Shack

Radio Shack ET-1110 Bedienungsanleitung

Radio Shack

Radio Shack 43-3535 Bedienungsanleitung

Radio Shack

Radio Shack 2.4 GHz Digital Spread Spectrum Cordless Telephone with Caller ID/Call Waiting... Bedienungsanleitung

Radio Shack

Radio Shack ET-3504 Bedienungsanleitung

Radio Shack

Radio Shack ET-1104 Bedienungsanleitung

Radio Shack

Radio Shack ET-1105 Bedienungsanleitung

Radio Shack

Radio Shack 43-1107 Bedienungsanleitung

Radio Shack

Radio Shack Cordless Telephone Bedienungsanleitung

Radio Shack

Radio Shack TAD-268 Bedienungsanleitung

Radio Shack

Radio Shack ET-598 Bedienungsanleitung

Radio Shack

Radio Shack 43-3575 Bedienungsanleitung

Radio Shack

Radio Shack ET-1125 Bedienungsanleitung

Radio Shack

Radio Shack 900 MHz Digital Spread Spectrum Cordless... Bedienungsanleitung

Radio Shack

Radio Shack Cordless Phone Bedienungsanleitung

Radio Shack

Radio Shack 43-3537 Bedienungsanleitung

Radio Shack

Radio Shack 43-3821 Bedienungsanleitung

Radio Shack

Radio Shack ET-1111 Bedienungsanleitung

Radio Shack

Radio Shack 43-324 Bedienungsanleitung

Radio Shack

Radio Shack pmn Bedienungsanleitung

Radio Shack

Radio Shack TAD-734 Bedienungsanleitung

Radio Shack

Radio Shack 43-3577 Bedienungsanleitung

Radio Shack

Radio Shack 43-3824 Bedienungsanleitung

Radio Shack

Radio Shack Big-Button Caller ID Trim Fone 43-3904 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung