Radio Shack ET-532 Bedienungsanleitung

Cat. No. 43-1032

OWNER’S MANUAL

10-Channel Cordless

Please read before using this equipment.

ET-532

Telephone with LCD Display

43-1032.fm Page 1 Tuesday, August 17, 1999 9:41 AM

FEATURES

COM-LOK and Radio Shack are registered trademarks used by Tandy Corporation.

Your Radio Shack ET-532 10-Channel

Cordless Telephone with LCD Display

offers the latest advances in cordless

phone technology, and includes these

features:

LCD Displa

— lets you see phone

numbers as you dial them or recall

them from the ET-532’s memory.

10-Channel Selector — lets you eas-

ily select the channel with the best

range and least interference.

Advanced Super CCT Circuitr

—

provides clarity comparable to a cord-

ed phone, reduces background noise,

and increases effective operating dis-

tance.

COM-LOK — ensures that other cord-

less phone users cannot use your

phone line while the handset is on the

base.

Automatic Securit

Access Code —

changes each time you return the

handset to the base to help prevent

other cordless phone users from using

your phone line while the handset is off

the base.

Flash — sends an electronic switch-

hook signal for use with special phone

services such as call waiting.

Handset Volume Control — lets you

control the volume of the sound you

hear through the handset.

hted Ke

pad — lights when you

press a key or when the phone rings to

make the phone easy to use in a dark

room.

Redial — quickly redials the last num-

ber dialed with the touch of a button.

Touch Tone or Pulse (Rotar

) Dial-

— lets you connect your phone to

either type of service.

30-Number Memor

Dialin

— lets

you store 30 phone numbers in memo-

ry for easy dialing.

Please read this Owner’s Manual care-

fully so you can enjoy all of your tele-

phone’s features.

Important: Cordless phones such as

this one require AC power to operate.

When the AC power is off, you cannot

dial out or receive incoming calls using

your ET-532. For this reason, the ET-

532 cordless phone should not be your

only telephone. To be safe, you should

alsohave aphonethatdoesnotrequire

AC power to operate (not a cordless

phone)soyoucanstillmakeandreceive

calls if there is an AC power failure.

43-1032.fm Page 2 Tuesday, August 17, 1999 9:41 AM

This telephone has been tested and

found to comply with all applicable UL

and FCC standards.

Your ET-532 operates on standard ra-

dio frequencies, as allocated by the

FCC. Therefore, it is possible for other

radio units operating on similar fre-

quencies, within a certain area, to in-

advertently intercept your conversa-

tions and/or cause interference on

your cordless telephone. This lack of

privacy can occur with any cordless

telephone.

For your records, we urge you to

record the serial number of your phone

in the space below. The serial number

is located on the bottom panel of the

base.

Serial Number ______________

Warning: To prevent fire or shock haz-

ard, do not expose this product to rain

or moisture.

This symbol is intended to alert you

to the presence of uninsulated dan-

gerous voltage within the product’s

enclosure that might be of sufficient

magnitude to constitute a risk of

electric shock. Do not open the

product’s case.

This symbol is intended to inform

you that important operating and

maintenance instructions are in-

cluded in the literature accompany-

ing this product.

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVIC-

ING TO QUALIFIED PERSONNEL.

CAUTION

43-1032.fm Page 3 Tuesday, August 17, 1999 9:41 AM

READ THIS BEFORE

INSTALLATION

We have designed your telephone to

conform to federal regulations, and

you can connect it to most telephone

lines. However, each device that you

connect to the phone line draws power

from the phone line. We refer to this

power draw as the device’s ringer

equivalence number, or REN. The

REN is shown on the bottom of your

phone’s base.

If you are using more than one phone

or other device on the line, add up all

the RENs. If the total is more than five,

your phone might not ring. In rural ar-

eas, a total REN of three might impair

ringer operation. If ringer operation is

impaired, remove a device from the

line.

FCC STATEMENT

This telephone complies with Part 68

FCC Rules

. You must, upon re-

quest, provide the FCC registration

number and the REN to your phone

company. These numbers are located

on the bottom of your phone’s base.

Note: You must not connect your

phone to any of the following:

• Coin-operated systems

• Party-line systems

• Most electronic key phone sys-

tems

43-1032.fm Page 4 Tuesday, August 17, 1999 9:41 AM

CONTENTS

Installation ............................................................................................................ 6

Selecting a Location ........................................................................................ 6

Installing the Phone ........................................................................................ 6

Preparation ........................................................................................................... 7

Installing the Battery ....................................................................................... 7

Charging the Battery ....................................................................................... 7

Setting the Dialing Mode ................................................................................. 8

Operation .............................................................................................................. 9

Making/Answering a Call ................................................................................ 9

Using the Handset at the Base ................................................................. 9

Using the Handset Away from the Base ................................................... 9

Reducing Interference ................................................................................... 10

Using Redial .................................................................................................. 10

Using Flash ................................................................................................... 10

Using Tone Services on a Pulse Line ........................................................... 11

Using Page ................................................................................................... 11

Memory Dialing ............................................................................................. 11

Storing a Number in Memory .................................................................. 12

Entering a Pause in a Memory Number ................................................. 13

Dialing a Stored Number ........................................................................ 13

Chain Dialing .......................................................................................... 14

Testing Stored Emergency Numbers ...................................................... 14

Troubleshootin

................................................................................................ 15

Care and Maintenance ...................................................................................... 17

Replacing the Battery .................................................................................... 18

The FCC Wants You to Know ....................................................................... 18

Lightning ....................................................................................................... 19

43-1032.fm Page 5 Tuesday, August 17, 1999 9:41 AM

INSTALLATION

SELECTING A LOCATION

Select a location for the telephone that

meets these requirements:

• Near an AC outlet

• Near a telephone line jack

• Out of the way of normal activities

• Away from electrical machinery,

electrical appliances, and metal

walls or filing cabinets

• Away from wireless intercoms,

alarms, and room monitors

The base’s location affects the phone’s

range. If you have a choice of several

locations, try each one to see which

provides the best performance.

If the phone line jack is not a modular

jack, you must update the wiring your-

self, using jacks and adapters avail-

able at your local Radio Shack store.

Or, you can let the phone company up-

date the wiring for you.

Notes:

• The phone company will charge

you for the installation of the nec-

essary jacks.

• The USOC number of the jack to

be installed is RJ11C.

INSTALLING THE PHONE

Follow these steps to install the base

on a desk, shelf, or table.

1. Plug one end of the supplied mod-

ular cord into the phone jack on

the back of the base.

2. Plug the modular cord’s other end

into a modular phone line jack.

3. Insert the supplied AC adapter’s

barrel plug into the DC 12V jack on

the back of the base.

4. Plug the adapter into a standard

AC outlet.

For the best reception, fully extend the

base’s antenna and place it in a verti-

cal position.

Caution: You must use a 120V AC/

12V DC adapter that delivers at least

200 milliamps. Its center tip must be

positive, and its plug must correctly fit

the phone’s DC 12V jack. The supplied

adapter meets these requirements.

Using an adapter that does not meet

these requirements could damage the

phone or the adapter.

43-1032.fm Page 6 Tuesday, August 17, 1999 9:41 AM

PREPARATION

INSTALLING THE

BATTERY

Before you use your phone for the first

time, you must install and charge the

battery.

To install the battery, slide off the bat-

tery compartment cover on the back of

the handset, connect the battery’s plug

to the pins inside the compartment,

and place the battery inside the com-

partment.

Replace the cover, then follow the in-

structions under “Charging the Bat-

tery.”

CHARGING THE

BATTERY

When you install a new battery, set

POWER to OFF. Then place the hand-

set on the cradle so the CHARGE/

TALK indicator lights and let the bat-

tery charge for about 15 hours.

When on the handset lights, re-

charge the battery. To avoid damage

to the battery, always recharge the

handset before battery power grows

too weak to light .

Notes:

• You can set POWER to ON while

the battery charges.

43-1032.fm Page 7 Tuesday, August 17, 1999 9:41 AM

• If the CHARGE/TALK indicator

does not light when you place the

handset on the cradle, be sure the

battery is connected to the pins

inside the battery compartment

and the AC adapter is securely

connected to the base. Also,

check the charging contacts on

the handset and base. If the con-

tacts are dirty or tarnished, gently

clean them with a pencil eraser.

• About once a month, fully dis-

charge the battery by keeping the

handset off the cradle until

flashes, then return the

handset to the cradle and fully

recharge the battery. If you do not

fully discharge and recharge the

battery periodically, it loses its

ability to fully recharge.

• The first time you use your phone

after installing a new battery, the

handset might not work and might

sound an error tone when you

press

TALK. This might also occur

when you recharge a battery that

has been completely discharged.

If this happens, be sure the hand-

set is turned on, then return the

handset to the cradle for 5 sec-

onds. This resets the security

access code.

SETTING THE DIALING

MODE

Set TONE/PULSE on the back of the

base for the type of service you have.

If you are not sure which type you

have, do this test.

1. Set TONE/PULSE to TONE.

2. Lift the handset and listen for a

dial tone.

3. Press any number other than 0.

4. If the dial tone stops, you have

touch-tone service.

If the dial tone continues, you have

pulse service. Set TONE/PULSE to

PULSE.

43-1032.fm Page 8 Tuesday, August 17, 1999 9:41 AM

OPERATION

Your ET-532’s LCD display shows

telephone numbers as you dial them or

when you recall them from memory. It

shows the current channel number and

lets you know when battery power is

growing weak or the phone is out of

range of the base. The display also

shows indicators when you pres

FLASH or PAUSE, or when you switch

from tone to pulse dialing.

MAKING/ANSWERING

A CALL

You can use your cordless telephone

in two ways: at the base or away from

the base.

Using the Handset

at the Base

You can use the handset at the base

like a regular corded telephone. Just

set POWER to ON and place the hand-

set in the cradle.

To answer a call, just lift the handset

from the base.

To make a call, lift the handset from

the base and press TALK so the key-

pad and the CHARGE/TALK indicator

on the base light.

Note: CH and the currently used

channel number appear on the display.

This number might change when you

return the handset to the base.

To disconnect a call, replace the hand-

set on the base.

Using the Handset

Away from the Base

To make or answer a call, set POWER

to ON and press TALK. The keypad

and CHARGE/TALK indicator light.

To disconnect a call, press TALK so

the keypad light and the CHARGE/

TALK indicator turn off.

Notes:

•CHand the currently used channel

number appear on the display.

• To conserve battery power, you

can turn off the handset’s power

when you are not making or

answering a call.

43-1032.fm Page 9 Tuesday, August 17, 1999 9:41 AM

• You can make or answer a call on

a phone on the same line as the

cordless phone, even if the hand-

set is away from the base.

•RANGE appears when the dis-

tance from the handset to the

base is out of the phone’s range.

• The keypad lights on the handset

turn off if no button is pressed for

more than 13 seconds.

REDUCING

INTERFERENCE

To reduce interference, press CH to

switch to the next channel (10 chan-

nels in all) until you receive the best re-

ception. CH and the channel number

appear on the display.

USING REDIAL

To quickly redial the last number you

dialed, simply lift the handset from the

base and press TALK again so the

CHARGE/TALK indicator lights, and

then press REDIAL. The redialed num-

ber appears on the display.

The redial memory holds up to 80 dig-

its in the tone mode or 81 digits in the

pulse mode. The redial memory also

holds pause entries (see “Entering a

Pause” under “Memory Dialing”).

Note: We recommend you not use RE-

DIAL to dial numbers that include a

tone (*) entry (see “Using Tone Servic-

es on a Pulse Line”).

USING FLASH

Use FLASH on the handset to perform

the switchhook operation for special

services, such as call waiting.

43-1032.fm Page 10 Tuesday, August 17, 1999 9:41 AM

Inhaltsverzeichnis

Andere Radio Shack Schnurloses Telefon Handbücher

Radio Shack

Radio Shack 43-3857 Bedienungsanleitung

Radio Shack

Radio Shack ET-1110 Bedienungsanleitung

Radio Shack

Radio Shack TAD-729 Bedienungsanleitung

Radio Shack

Radio Shack CID-927 Bedienungsanleitung

Radio Shack

Radio Shack TAD-794 Bedienungsanleitung

Radio Shack

Radio Shack TAD-727 Bedienungsanleitung

Radio Shack

Radio Shack 43-1122 Bedienungsanleitung

Radio Shack

Radio Shack TAD 1130 Bedienungsanleitung

Radio Shack

Radio Shack 43-3537 Bedienungsanleitung

Radio Shack

Radio Shack ET-919 Bedienungsanleitung

Radio Shack

Radio Shack 43-3824 Bedienungsanleitung

Radio Shack

Radio Shack 43-3578 Bedienungsanleitung

Radio Shack

Radio Shack Presidian Bedienungsanleitung

Radio Shack

Radio Shack TAD-1015 Bedienungsanleitung

Radio Shack

Radio Shack 900 MHz Digital Spread Spectrum Cordless Phone with Digital Answerer and Caller ID/Call Waiting... Bedienungsanleitung

Radio Shack

Radio Shack 43-3701 Bedienungsanleitung

Radio Shack

Radio Shack ET-521 Bedienungsanleitung

Radio Shack

Radio Shack ET-686 Bedienungsanleitung

Radio Shack

Radio Shack ET-3504 Bedienungsanleitung

Radio Shack

Radio Shack ET-927 Bedienungsanleitung

Radio Shack

Radio Shack 43-3548 Bedienungsanleitung

Radio Shack

Radio Shack ET-1102 Bedienungsanleitung

Radio Shack

Radio Shack Big-Button Caller ID Trim Fone 43-3904 Bedienungsanleitung

Radio Shack

Radio Shack 43-3575 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung