Radio Shack TAD-1010 Bedienungsanleitung

Cat. No. 43-771

OWNER’S MANUAL

900 MHz Digital Cordless Telephone

Please read before using this equipment.

TAD-1010

with Digital Multi-User

Answering System

43-771.fm Page 1 Friday, August 13, 1999 2:59 PM

Radio Shack is a registered trademark used by Tandy Corporation.

This symbol is intended to alert you to

the presence of uninsulated danger-

ousvoltage within the product’s enclo-

sure that might be of sufficient

magnitude to constitute a risk of elec-

tric shock. Do not open the product’s

case.

This symbol is intended to inform you

that important operating and mainte-

nance instructions are included in the

literature accompanying this product.

READ THIS BEFORE

INSTALLATION

Your TAD conforms to federal regula-

tions, and you can connect it to most

telephone lines. However, each device

you connect to the phone line draws

power from the phone line. We refer to

this power draw as the device’s ringer

equivalence number, or REN. The REN

is on the label on the back of the base.

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVIC-

ING TO QUALIFIED PERSONNEL.

Warnin

: To prevent fire or shock

hazard, do not expose this product

to rain or moisture.

CAUTION !

If you are using more than one phone

or other device on the line, add up all

the RENs. If the total is more than five,

your phone might not ring. In rural ar-

eas, a total REN of three might impair

ringer operation. If ringer operation is

impaired, remove a device from the

line.

FCC STATEMENT

This telephone complies with Part 68 of

FCC Rules

. You must, upon request,

provide the FCC Registration Number

and the REN to your phone company.

These numbers are on the label on the

back of the base.

You must not connect your phone to

any of the following:

• Coin-operated systems

• Party-line systems

• Most electronic key phone systems

Note: Your telephone operates on

standard radio frequencies, as allocat-

ed by the FCC. Even though the secu-

rity access protection code prevents

unauthorized use of your phone line, it

is possible for other radio units operat-

ing on similar frequencies within a cer-

tain area to unintentionally intercept

your conversations and/or cause inter-

ference. This lack of privacy can occur

with any cordless phone.

43-771.fm Page 2 Friday, August 13, 1999 2:59 PM

FEATURES

Your Radio Shack TAD-1010 900 MHz

Digital Cordless Telephone with Digital

Multi-User Answering System uses ad-

vanced analog cordless telephone

technology to give you superior audio

quality. It uses the recently allocated

900 MHz band which has less interfer-

ence and clearer sound and greater

range than 46/49 MHz cordless tele-

phones. Its cordless operation lets you

move freely about your home or office.

The Telephone Answering Device

(TAD) stores all messages on a com-

puter chip. This gives you advanced ca-

pabilities over tape-based answering

machines. For example, you can save

individual messages while the rest are

erased. Because your TAD is fully digi-

tal, there are no tape mechanisms to

wear out and no tapes to bother with.

The TAD can record messages for four

users with individual date/time stamps

for each message. The TAD’s 30-

minute memory capacity means you

can store a lot of messages!

Its remote operation features let you ac-

cess your TAD remotely from a touch-

tone phone. The TAD guides you

through system operation with voice

prompts.

Cordless Telephone Features

900 MHz Operation —provides lower

interference than 46/49 MHz phones.

itall

Encoded Si

nal — prevents

other people from picking up your

phone’s signal (on scanners, for exam-

ple) and listening to your conversations.

10 Channels — scans 10 channels

(frequency pairs used between the

base and the handset) and selects a

clear one each time you make or re-

ceive a call. You can also manually

change channels during a call.

Securit

Access-Protection Code —

changes each time you place the hand-

set on the base, to minimize the chanc-

es of other cordless phones using your

phone line.

Out of Ran

e Si

nal — the handset

beeps to let you know when it is out of

the base’s operating range.

stem — lets you send a sig-

nal from the base to the handset so you

can page someone or easily locate the

handset when it is away from the base.

10-Number Memor

Dialin

— lets

you store up to 10 phone numbers in

memory for easy dialing.

Privac

— prevents the person on the

other end of the phone line from hear-

ing your conversation with someone in

the room.

43-771.fm Page 3 Friday, August 13, 1999 2:59 PM

Digital Volume Control — lets you ad-

just the playback volume of the record-

ings on the TAD.

Announcement Only — lets you

record an announcement for callers to

hear, without recording their messag-

es.

LCD Message Counter — shows the

number of messages the TAD has re-

corded.

Remote Operation — lets you use a

touch-tone phone (or rotary phone and

pocket tone dialer) to operate the TAD

while you are away from your home or

office.

Programmable Remote Operation

Security Code — lets you set a securi-

ty code for remote operation.

Remote Answer-On — lets you call

the TAD from a remote location and set

it to answer calls.

Call Screening — lets you listen as a

caller leaves a message so you can

decide whether or not to answer the

call.

Memo Recording — lets you leave

messages for yourself or others in your

home or office.

Adjustable Ring Number — lets you

set the TAD to answer after two or four

rings.

Flash — sends an electronic switch-

hook signal for use with special phone

services such as call waiting.

Redial — lets you quickly dial the last

number dialed.

Hold — lets you place a call on hold.

Programmable Ringer — lets you se-

lect from four ringer types and turn the

ringer on or off.

Touch-Tone (DTMF) or Pulse Dialing

— lets you use your phone with either

type of dialing.

Handset Volume Control — lets you

adjust the volume of the sound you hear

through the handset.

Hearing Aid Compatible — lets you

use this telephone with hearing aids that

have a T (telephone) switch.

TAD Features

Four User Mailboxes — let you store

and play back messages for up to four

different users. The generic mailbox

stores and plays back messages for all

users.

Date/Time Stamp — records the day

and time each message was recorded.

Digitally-Synthesized Voice — guides

you through operation of the system.

43-771.fm Page 4 Friday, August 13, 1999 2:59 PM

Toll-Saver — lets you avoid unneces-

sary long-distance charges when you

call by long distance to check your mes-

sages.

Phone Pick-Up Detection — stops re-

cording when you pick up any phone on

the same line as the TAD, and resets to

answer the next call.

This TAD has been tested and found to

comply with all applicable UL and FCC

standards.

Important: Cordless phones such as

this one require AC power to operate.

When AC power is off, you cannot dial

out or receive incoming calls using your

TAD-1010. For this reason, the TAD-

1010 should not be your only telephone.

To be safe, you should also have a

phone that does not require AC power to

operate (not a cordless phone) so you

can still make and receive calls if there

is an AC power failure.

For your records, we recommend you

record the TAD’s serial number here.

The number is on the base’s label.

Serial Number ________________

43-771.fm Page 5 Friday, August 13, 1999 2:59 PM

CONTENTS

Installation ...................................................................................................... 8

Installing the Backup Battery ..................................................................... 8

Selecting a Location .................................................................................. 9

Placing the Base on a Desktop ................................................................. 9

Mounting the Base on a Wall ..................................................................... 9

Mounting on a Wall Plate .................................................................. 10

Mounting Directly on the Wall ............................................................ 11

Telephone Preparation ................................................................................ 13

Installing the Handset Battery Pack ......................................................... 13

Charging the Handset Battery Pack ........................................................ 14

Setting the Pulse/Tone Switch ................................................................. 15

Setting the Telephone Ringer .................................................................. 15

Checking the Ringer ......................................................................... 16

Turning Off the Ringer ....................................................................... 16

Telephone Operation ................................................................................... 17

Answering/Making a Call ......................................................................... 17

Adjusting the Handset’s Volume .............................................................. 17

Using Redial ............................................................................................ 18

Using Privacy ........................................................................................... 18

Using Hold ............................................................................................... 18

Using Flash .............................................................................................. 18

Using Tone Services on a Pulse Line ...................................................... 19

Using Page .............................................................................................. 19

Changing Channels ................................................................................. 19

Memory Operation ................................................................................... 20

Storing a Number in Memory ............................................................ 20

Storing a Pause in Memory ............................................................... 21

Dialing a Stored Number ................................................................... 21

Chain Dialing Service Numbers ........................................................ 21

TAD Setup and Basic Operation ................................................................. 22

Setting the Number of Rings ................................................................... 22

Setting the Remote Operation Security Code ......................................... 22

Setting the Day and Time ........................................................................ 23

Setting the Number of Mailboxes ............................................................ 23

Selecting an Announcement .................................................................... 24

Recording an Announcement ........................................................... 24

Checking the Outgoing Announcement ............................................ 25

Setting the TAD to Answer Calls ............................................................. 26

43-771.fm Page 6 Friday, August 13, 1999 2:59 PM

Recording a Memo ................................................................................... 26

Playing Messages .................................................................................... 27

Adjusting the TAD’s Volume ..................................................................... 28

Erasing Messages .................................................................................... 28

Remote Operation ......................................................................................... 29

Using the Toll-Saver ................................................................................. 29

Accessing the TAD by Remote ................................................................. 29

From the Cordless Handset ............................................................... 29

From Another Phone Line .................................................................. 29

Using Remote Commands ....................................................................... 30

Remote Operation Commands .......................................................... 31

Troubleshooting ............................................................................................ 32

Out of Range Indications .......................................................................... 34

Out of Range with No Call ................................................................. 34

Out of Range with a Call in Progress ................................................. 34

Care and Maintenance .................................................................................. 35

The FCC Wants You to Know ................................................................... 36

Lightning ................................................................................................... 36

43-771.fm Page 7 Friday, August 13, 1999 2:59 PM

INSTALLATION

INSTALLING THE

BACKUP BATTERY

If the AC power fails or you unplug the

TAD-1010, a 9V backup battery (not

supplied) saves the messages and the

settings for the day, time, and security

code. We recommend you use an alka-

line battery, such as Radio Shack Cat.

No. 23-553.

Follow these steps to install the backup

battery.

Cautions:

• Before you replace the battery, be

sure the supplied adapter is

securely connected to an AC outlet

and to the jack on the back of the

TAD. Otherwise, you might lose any

stored information.

• Always use a fresh battery of the

required size and type.

• Dispose of the battery promptly and

properly. Do not bury or burn it.

1. Remove the battery compartment

cover on the bottom of the base by

sliding the cover in the direction of

the arrow.

2. Snap the battery’s contacts firmly

to the battery connector, then place

the battery into the compartment.

3. Replace the cover.

Note: If flashes after installing a

fresh backup battery, unplug the AC

adapter from the AC outlet (if connect-

ed), then reconnect it.

ANNC.

SAT

43-771.fm Page 8 Friday, August 13, 1999 2:59 PM

SELECTING A LOCATION

You can set the TAD-1010’s base on a

flat surface (such as a desktop or coun-

tertop), or mount it on a wall plate or di-

rectly on the wall. The base’s location

affects the phone’s range. If you have a

choice of several locations, try each to

see which one provides the best perfor-

mance.

Select a location that is:

• Near an AC outlet

• Near a modular telephone line jack

• Away from electrical machinery,

electrical appliances, and metal

walls or filing cabinets

• Away from wireless intercoms,

alarms, and room monitors

If the phone line jack is not a modular

jack, you must update the wiring. You

can convert the wiring yourself, using

jacks and adapters available at your lo-

cal Radio Shack store. Or, you can let

the phone company update the wiring

for you.

Notes:

• The phone company charges for

the installation of the necessary

jacks.

• The USOC number of the base-

board jack to be installed is RJ11C.

PLACING THE BASE ON A

DESKTOP

1. Plug one end of the supplied 7-foot

modular cord into the TO TEL. LINE

jack on the back of the TAD-1010’s

base.

2. Plug the modular cord’s other end

into a modular phone line jack.

3. Plug the TAD-1010’s AC cord into a

standard AC outlet.

4. For the best reception, adjust the

base’s antenna so it stands straight

up.

MOUNTINGTHEBASEON

A WALL

Using the supplied mounting bracket,

you can mount the TAD-1010’s base on

a phone jack wall plate or directly on

the wall.

TO TEL. LINE

43-771.fm Page 9 Friday, August 13, 1999 2:59 PM

To prepare the bracket for mounting,

twist off the tabs attached to the center

of the bracket and press them securely

into the holes on the narrow end of the

bracket.

Mounting on a Wall Plate

1. Plug one end of the supplied 7-inch

modular cord into the TO TEL. LINE

jack.

2. Insert the tabs on the supplied

mounting bracket into the slots on

the base’s bottom. Then press the

bracket down until it snaps into

place.

3. Press the AC cord into the top and

bottom grooves on the left side of

the bracket. Press the modular cord

TOTEL. LINE

into the center groove on the right

side of the bracket, then plug the

modular cord into the modular

phone jack.

4. Line up the keyhole slots on the

bracket with the studs on the wall

plate, then slide the base down

onto the wall plate until it is secure.

5. Press up on the handset holder to

remove it, turn it over so its tabbed

edge faces up, then press it back

down into its slot on the base.

6. Plug the TAD-1010’s AC cord into

a standard AC outlet.

900MHz DIGITALTELEPHONE • ANSWERING SYSTE

MEMO

ANNC.

MEMORY

MAIL BOX

MULTI-USER

DIGITAL ANSWERING SYSTEM

TAD-101

MULTI-USER

DIGITAL ANSWERING SY STEM

43-771.fm Page 10 Friday, August 13, 1999 2:59 PM

Inhaltsverzeichnis

Andere Radio Shack Schnurloses Telefon Handbücher

Radio Shack

Radio Shack ET-917 Bedienungsanleitung

Radio Shack

Radio Shack ET-557 Bedienungsanleitung

Radio Shack

Radio Shack ET-1111 Bedienungsanleitung

Radio Shack

Radio Shack Presidian Bedienungsanleitung

Radio Shack

Radio Shack 43-3571 Bedienungsanleitung

Radio Shack

Radio Shack 43-3824 Bedienungsanleitung

Radio Shack

Radio Shack ET-3504 Bedienungsanleitung

Radio Shack

Radio Shack 43-325 Bedienungsanleitung

Radio Shack

Radio Shack 43-3701 Bedienungsanleitung

Radio Shack

Radio Shack Digital Answering System with Caller ID Deluxe and 2.4 GHz Digital Spread Spectrum Cordless... Bedienungsanleitung

Radio Shack

Radio Shack 43-3556 Bedienungsanleitung

Radio Shack

Radio Shack ET-545 Bedienungsanleitung

Radio Shack

Radio Shack Caller ID System 1500 Bedienungsanleitung

Radio Shack

Radio Shack 2.4 GHz 2-Line Digital Spread Spectrum Cordless Phone with Call Waiting/Caller... Bedienungsanleitung

Radio Shack

Radio Shack ET-1123 Bedienungsanleitung

Radio Shack

Radio Shack 43-3880 Bedienungsanleitung

Radio Shack

Radio Shack 43-164 Bedienungsanleitung

Radio Shack

Radio Shack ET-686 Bedienungsanleitung

Radio Shack

Radio Shack 43-3535 Bedienungsanleitung

Radio Shack

Radio Shack TAD-727 Bedienungsanleitung

Radio Shack

Radio Shack Two-Line Caller ID Phone With Speakerphone Bedienungsanleitung

Radio Shack

Radio Shack 43-3502 Bedienungsanleitung

Radio Shack

Radio Shack ET-596 Bedienungsanleitung

Radio Shack

Radio Shack ET-539 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung