ResMed AirCurve 10 CS PaceWave Bedienungsanleitung

User guide

English 1

ENGLISH

Welcome

The AirCurve™ 10 CS PaceWave is a positive airway pressure device that belongs to the adaptive

servo-ventilator category.

WARNING

•Read this entire guide before using the device.

•Use the device according to the intended use provided in this guide.

•The advice provided by your prescribing doctor should be followed ahead of the

information provided in this guide.

•This device is not suitable for ventilator-dependent patients.

AirCurve 10 CS PaceWave indications for use

The AirCurve 10 CS PaceWave is indicated to stabilise the ventilation of adult patients exhibiting

central sleep apnoea (CSA), mixed sleep apnoea and periodic breathing, with or without obstructive

sleep apnoea. It is intended for home and hospital use.

The humidifier is intended for single patient use in the home environment and re-use in a

hospital/institutional environment.

Clinical benefits

The clinical benefit of CPAP therapy is a reduction in apnoeas, hypopnoeas and sleepiness, as well

as improved quality of life. The clinical benefit of ASV therapy for the treatment of CSA is a

reduction in apnoeas and hypopnoeas.

The clinical benefit of humidification is the reduction of positive airway pressure related side effects.

Contraindications

ASV therapy is contraindicated in patients with chronic, symptomatic heart failure (NYHA 2-4) with

reduced left ventricular ejection fraction (LVEF ≤ 45%) and moderate to severe predominant central

sleep apnoea.

Positive airway pressure therapy may be contraindicated in some patients with the following

pre-existing conditions:

•severe bullous lung disease

•pneumothorax or pneumomediastinum

•pathologically low blood pressure, particularly if associated with intravascular volume depletion

•dehydration

•cerebrospinal fluid leak, recent cranial surgery, or trauma.

Adverse effects

You should report unusual chest pain, severe headache, or increased breathlessness to your

prescribing physician. An acute upper respiratory tract infection may require temporary

discontinuation of treatment.

The following side effects may arise during the course of therapy with the device:

•drying of the nose, mouth, or throat

•nosebleed

•bloating

•ear or sinus discomfort

•eye irritation

•skin rashes.

At a glance

The AirCurve 10 includes the following:

•Device

•HumidAir™humidifier (if supplied)

•Air tubing

•Power supply unit

•Travel bag

•SD card (not available in all devices).

Contact your care provider for a range of accessories available for use with the device including:

•Air tubing (heated and non-heated): ClimateLineAir™, SlimLine™, ClimateLineAir Oxy, Standard

•Side cover for use without the humidifier

•Filter: Hypoallergenic filter, standard filter

•Air10™DC/DC converter (12V/24V)

•SD card reader

•Air10 oximeter adapter

•Air10 USB adapter

•Power Station II

•Air10 tubing elbow.

English 3

About your device

Air outlet

HumidAir humidifier

Air filter cover

Screen

Power inlet

Adapter cover

Serial number and device number

SD card cover

About the control panel

Start/Stop button

Press to start/stop therapy.

Press and hold for three seconds to enter power save

mode.

Dial

Turn to navigate the menu and press to select an option.

Turn to adjust a selected option and press to save your

change.

Home button Press to return to the Home screen.

Different icons may be displayed on the screen at different times including:

Ramp Time

Wireless signal strength (green)

Humidity

Wireless transfer not enabled (grey)

Humidifier warming

No wireless connection

Humidifier cooling

Airplane Mode

Setup

CAUTION

Do not overfill the humidifier as water may enter the device and air tubing.

1. Place the device on a stable level surface.

2. Plug the power connector into the rear of the device. Connect one end of the power cord into

the power supply unit and the other end into the power outlet.

3. Connect the air tubing firmly to the air outlet located on the rear of the device.

4. Open the humidifier and fill it with water up to the maximum water level mark.

Do not fill the humidifier with hot water.

5. Close the humidifier and insert it into the side of the device.

6. Connect the free end of the air tubing firmly onto the assembled mask.

See the mask user guide for detailed information.

Recommended masks are available on www.resmed.com.

English 5

Performing a functional check

1. With the device powered off:

•Check the condition of the device and accessories.

Inspect the device and all the provided accessories. If there are any visible defects, the

system should not be used.

•Check the air tubing setup.

Check the integrity of the air tubing. Connect the air tubing firmly to the air outlet and other

accessories if in use.

2. Turn the device on.

3. Check the HumidAir humidifier (if in use).

Press Start/Stop on the device. The Sleep Report screen will display at the bottom of the

screen if the humidifier is in use.

Starting therapy

1. Fit your mask.

See the mask guide for fitting instructions or use the Mask Fit function to check the mask fit and

seal.

2. Press Start/Stop or breathe normally if SmartStart™is enabled.

You will know that therapy is on when the Sleep Report screen is displayed.

The pressure bar shows the inspiratory and expiratory pressures in green.

The green bar will expand and contract as you breathe in and out.

The screen will go black automatically after a short period of time. You can press Home or the dial to

turn it back on. If power is interrupted during therapy, the device will automatically restart therapy

when power is restored.

The AirCurve 10 device has a light sensor that adjusts the screen brightness based on the light in

the room.

Stopping therapy

1. Remove your mask.

2. Press Start/Stop or if SmartStart is enabled, therapy will stop automatically after a few seconds.

The Sleep Report now gives you a summary of your therapy session.

Usage hours–Indicates the number of hours of therapy you received last

session.

Mask Seal–Indicates how well your mask sealed:

Good mask seal.

Needs adjusting, see Mask Fit.

Humidifier–Indicates if your humidifier is working properly:

Humidifier working.

Humidifier might be faulty, contact your care provider.

If set by your care provider, you will also see:

Events per hour–Indicates the number of apnoeas and hypopnoeas experienced per hour.

More Info–Turn the dial to scroll down to view more detailed usage data.

Power save mode

Your AirCurve 10 device records your therapy data. In order to allow it to transmit the data to your

care provider, you should not unplug the device. However, you can put it into power save mode to

save electricity.

To enter power save mode:

•Press and hold Start/Stop for three seconds.

The screen goes black.

To exit power save mode:

•Press Start/Stop once.

The Home screen is displayed.

My Options

Your AirCurve 10 device has been set up for your needs by your care provider, but you may find you

want to make small adjustments to make your therapy more comfortable.

Highlight My Options and press the dial to see your

current settings. From here, you can personalise your

options.

English 7

Ramp Time

Designed to make the beginning of therapy more comfortable, Ramp Time is the period during

which the pressure increases from a low start pressure to the prescribed treatment pressure.

You can set your Ramp Time to Off or between 5 to 45 minutes.

To adjust Ramp Time:

1. In My Options, turn the dial to highlight Ramp

Time and then press the dial.

2. Turn the dial to adjust the ramp time to your

preferred setting and press the dial to save the

change.

Humidity Level

The humidifier moistens the air and is designed to make therapy more comfortable. If you are

getting a dry nose or mouth, turn up the humidity. If you are getting any moisture in your mask, turn

down the humidity.

You can set the Humidity Level to Off or between 1 and 8, where 1 is the lowest humidity setting

and 8 is the highest humidity setting.

To adjust the Humidity Level:

1. In My Options, turn the dial to highlight Humidity

Level and then press the dial.

2. Turn the dial to adjust the humidity level and press

the dial to save the change.

If you continue to get a dry nose or mouth, or moisture in your mask, consider using ClimateLineAir

heated air tubing. ClimateLineAir together with Climate Control delivers more comfortable therapy.

Mask Fit

Mask Fit is designed to help you assess and identify possible air leaks around your mask.

To check Mask Fit:

1. Fit the mask as described in the mask user guide.

2. In My Options, turn the dial to highlight Run Mask Fit and then press the

dial.

The device starts blowing air.

3. Adjust the mask, mask cushion and headgear until you get a Good result.

To stop Mask Fit, press the dial or Start/Stop. If you are unable to get a good mask seal, assess

whether you have the right mask size and/or type or talk to your care provider.

More options

There are some more options on your device which you can personalise.

Leak Alert* When Leak Alert is enabled, the device beeps if the mask leaks too much air or if you remove

the mask during therapy.

SmartStart* When SmartStart is enabled, therapy starts automatically when you breathe into your mask.

When you remove your mask, it stops automatically after few seconds.

*When enabled by your care provider.

Caring for your device

It is important that you regularly clean your AirCurve 10 device to make sure you receive optimal

therapy. The following sections will help you with disassembling, cleaning, checking and

reassembling your device.

WARNING

Regularly clean your tubing assembly, humidifier and mask to receive optimal therapy and to

prevent the growth of germs that can adversely affect your health.

Disassembling

1. Hold the humidifier at the top and bottom, press it gently and pull it away from the device.

2. Open the humidifier and discard any remaining water.

3. Hold the cuff of the air tubing and gently pull it away from the device.

4. Hold both the cuff of the air tubing and the swivel of the mask, then gently pull apart.

English 9

Cleaning

You should clean the device weekly as described. Refer to the mask user guide for detailed

instructions on cleaning your mask.

1. Wash the humidifier and air tubing in warm water using mild detergent.

2. Rinse the humidifier and air tubing thoroughly and allow to dry out of direct sunlight and/or heat.

3. Wipe the exterior of the device with a dry cloth.

Notes:

•The humidifier may be washed in a dishwasher on the delicate or glassware cycle (top shelf only).

It should not be washed at temperatures higher than 65ºC.

•Do not wash the air tubing in a dishwasher or washing machine.

•Empty the humidifier daily and wipe it thoroughly with a clean, disposable cloth. Allow to dry out

of direct sunlight and/or heat.

Checking

You should regularly check the humidifier, air tubing and the air filter for any damage.

1. Check the humidifier:

•Replace it if it is leaking or has become cracked, cloudy or pitted.

•Replace it if the seal is cracked or torn.

•Remove any white powder deposits using a solution of one part household vinegar to

10 parts water.

2. Check the air tubing and replace it if there are any holes, tears or cracks.

3. Check the air filter and replace it at least every six months. Replace more often if there are any

holes or blockages by dirt or dust.

To replace the air filter:

1. Open the air filter cover and remove the old air filter.

The air filter is not washable or reusable.

2. Place a new air filter onto the air filter cover and then close it.

Make sure the air filter is fitted at all times to prevent water and dust from entering the device.

Reassembling

When the humidifier and air tubing are dry, you can reassemble the parts.

1. Connect the air tubing firmly to the air outlet located on the rear of the device.

2. Open the humidifier and fill it with room temperature water up to the maximum water level

mark.

Andere Handbücher für AirCurve 10 CS PaceWave

Inhaltsverzeichnis

Sprachen:

Andere ResMed Medizinische Geräte Handbücher

ResMed

ResMed AirFit N30 Bedienungsanleitung

ResMed

ResMed VS Ultra Bedienungsanleitung

ResMed

ResMed NV Elbow F20 Bedienungsanleitung

ResMed

ResMed Mirage SoftGel Bedienungsanleitung

ResMed

ResMed VPAP Malibu Bedienungsanleitung

ResMed

ResMed AIRMINI Bedienungsanleitung

ResMed

ResMed S8 AutoScore II Bedienungsanleitung

ResMed

ResMed AirFit N20 Bedienungsanleitung

ResMed

ResMed VPAP ST Technisches Handbuch

ResMed

ResMed Mirage Micro Bedienungsanleitung

ResMed

ResMed airsense 10 autoset Bedienungsanleitung

ResMed

ResMed AirFit N30i Bedienungsanleitung

ResMed

ResMed C28173 Bedienungsanleitung

ResMed

ResMed AirFit N20 Bedienungsanleitung

ResMed

ResMed S9 Series Technisches Handbuch

ResMed

ResMed airsense 10 autoset Montageanleitung

ResMed

ResMed airsense 10 autoset Leitfaden

ResMed

ResMed Mirage SoftGel Bedienungsanleitung

ResMed

ResMed Elisee 350 Gebrauchsanweisung

ResMed

ResMed AirFit N20 Bedienungsanleitung

ResMed

ResMed Mirage Swift II Bedienungsanleitung

ResMed

ResMed ApneaLink Bedienungsanleitung

ResMed

ResMed ApneaLink Bedienungsanleitung

ResMed

ResMed Mirage Kidsta Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung