ResMed VPAP COPD Bedienungs- und Sicherheitshinweise

Making quality of care easy

Respiratory Care Solutions

Welcome Guide

English

VPAP™COPD

NONINVASIVE VENTILATOR

H5i™

HEATED HUMIDIFIER

Making quality of care easy

Respiratory Care Solutions

Welcome

Thank you for choosing the VPAP COPD or H5i™. Before operating the device, please read the entire

Welcome and Information Guides.

VPAP COPD at a glance

The VPAP COPD system comprises the following elements:

• VPAP COPD device • Air tubing • 90W power supply unit • S9 Travel bag • SD card • S9 SD card

protective folder.

Optional components include:

• H5i heated humidifier • Standard air tubing • SlimLine™ air tubing • 3 m air tubing • ClimateLine™

heated air tubing • ClimateLineMAX heated air tubing • ClimateLineMAX Oxy heated air tubing

•30Wpower supply unit (does not support H5i) • Power Station II battery pack

•DC/DC Converter 24V/90W.

Traveling tips

When traveling with your VPAP COPD only:

• Ensure you pack the SlimLine or Standard air tubing as the ClimateLine, ClimateLineMAX and

ClimateLineMAX Oxy heated air tubing are not designed to connect directly to the device.

• Ensure you purchase and travel with the approved power cord for the region where you will be using

the device.

Air filter

DC power inlet

SD card slot

Module/Adapter port

Air outlet

English

H5i at a glance

The H5i system comprises the following elements:

• H5i heated humidifier • H5i standard water tub

•ClimateLineMAX Oxy heated air tubing (if sold as a Climate Control Kit).

Optional components include:

• ClimateLineMAX heated air tubing • ClimateLine heated air tubing • H5i cleanable water tub.

Traveling tips

When moving or traveling with your H5i:

• Ensure that the water tub is empty.

• Disconnect the H5i from the device by using the release button.

Latch

Flip lid

Air outlet

H5i water tub

Release

button

Flip lid seal

ClimateLine, ClimateLineMAX

or ClimateLineMAX Oxy

connection port

Setting up

5 2

English

Setting up with supplemental oxygen

If oxygen is prescribed by your clinician, set up the VPAP COPD with the H5i and the ClimateLineMAXOxy

as follows:

1. Align your H5i with the VPAP COPD and push them together until they click into place.

2. Connect the DC plug of the power supply unit to the rear of the device.

3. Connect the power cord to the power supply unit.

4. Plug the other end of the power cord into the power outlet.

5. Connect one end of the air tubing firmly onto the air outlet.

6. Connect the assembled mask system to the free end of the air tubing.

7. Connect the oxygen supply tubing to the oxygen connector of the ClimateLineMAXOxy. Ensure that it

is attached firmly.

Note: Before adding oxygen, familiarize yourself with the specific warnings relating to the use of

supplemental oxygen. These can be found at the end of the Information Guide.

Setting up without supplemental oxygen

If you use the VPAP COPD with the ClimateLineMAXOxy but without supplemental oxygen, perform

steps1-6 above. Ensure that the cap of the oxygen connector is attached firmly.

Notes:

•Always ensure that the VPAP COPD and H5i are placed on a stable, level surface for proper operation.

•Always ensure that the VPAP COPD is placed in an area where the alarm LED indicators are clearly

visible.

•Place the power supply unit away from the H5i to allow for adequate ventilation.

•For more information on assembling your mask see your mask user guide. Recommended masks are

available on www.resmed.com on the Products page under Service & Support.

Filling the water tub

1. Slide the latch and lift open the flip lid.

2. Remove the water tub.

3. Fill the water tub (through the center hole) with distilled or deionized water

up to the maximum water level mark (12.5 fl oz / 380 mL).

4. Return the water tub to the H5i.

5. Close the flip lid ensuring that it clicks into place.

English

VPAP COPD basics

Info menu*

Allows you to view your sleep statistics or exit

from the menu.

Start/Stop button

Starts or stops

treatment.

LCD screen

Displays the menus, treatment

screens and reminders.

Push dial

Turning the dial allows you to scroll through the menu

and change settings. Pushing the dial allows you to

enter into a menu and confirm your choice.

Alarm mute

Press once to mute

alarms. Press a second

time to unmute.

Alarm and therapy LEDs

Yellow—flashes during an alarm.

Blue—on during therapy (if enabled

by clinician).

Key:

Home

Humidity Level

Ramp

Heated Tube

Climate Control

Start/Stop

Push dial

Alarm mute

Setup menu

Info menu

Setup menu*

Allows you to make changes to settings or exit from

the menu.

*The Info and Setup menus are disabled if S9 Essentials has been enabled by your clinician.

Adjusting humidity level

Ranging from OFF to 6, you can adjust the humidity level at any time to find the setting that is most

comfortable for you. To adjust the humidity level:

Warming the H5i

The warm-up feature is used to pre-heat the water before starting

treatment.

To start warming:

1. Navigate to the humidity level icon.

2. Push and hold for three seconds. The Warming Up status

bar is displayed.

You can stop warm-up at any time by pressing for at least three

seconds. You can start treatment at any time by pressing .

Note: In order to assist the heater plate in cooling, your device will

continue to blow air for up to an hour after treatment has stopped.

However, you can unplug the device from the power outlet at any time

and allow the heater plate to cool without air flow.

1. From your HOME

screen, turn

until the HUMIDITY

LEVEL screen is

displayed in blue.

2. Press .

The selection is

highlighted in

orange.

3. Turn until

the humidity level

that you require is

displayed.

4. Press to

confirm your choice.

VPAP COPD basics

Info menu*

Allows you to view your sleep statistics or exit

from the menu.

Start/Stop button

Starts or stops

treatment.

LCD screen

Displays the menus, treatment

screens and reminders.

Push dial

Turning the dial allows you to scroll through the menu

and change settings. Pushing the dial allows you to

enter into a menu and confirm your choice.

Alarm mute

Press once to mute

alarms. Press a second

time to unmute.

Alarm and therapy LEDs

Yellow—flashes during an alarm.

Blue—on during therapy (if enabled

by clinician).

Key:

Home

Humidity Level

Ramp

Heated Tube

Climate Control

Start/Stop

Push dial

Alarm mute

Setup menu

Info menu

Setup menu*

Allows you to make changes to settings or exit from

the menu.

*The Info and Setup menus are disabled if S9 Essentials has been enabled by your clinician.

Adjusting humidity level

Ranging from OFF to 6, you can adjust the humidity level at any time to find the setting that is most

comfortable for you. To adjust the humidity level:

Warming the H5i

The warm-up feature is used to pre-heat the water before starting

treatment.

To start warming:

1. Navigate to the humidity level icon.

2. Push and hold for three seconds. The Warming Up status

bar is displayed.

You can stop warm-up at any time by pressing for at least three

seconds. You can start treatment at any time by pressing .

Note: In order to assist the heater plate in cooling, your device will

continue to blow air for up to an hour after treatment has stopped.

However, you can unplug the device from the power outlet at any time

and allow the heater plate to cool without air flow.

1. From your HOME

screen, turn

until the HUMIDITY

LEVEL screen is

displayed in blue.

2. Press .

The selection is

highlighted in

orange.

3. Turn until

the humidity level

that you require is

displayed.

4. Press to

confirm your choice.

English

Adjusting ramp time

Designed to make the beginning of treatment more comfortable, ramp time is the period during which

the pressure increases from a low start pressure to the treatment pressure. To adjust your ramp time:

Using Mask Fit

You can use Mask Fit to help you fit your mask properly. This feature delivers CPAP pressure for a

three-minute period, prior to starting treatment, during which you can check and adjust your Mask Fit to

minimize leaks.

1. Fit your mask as described in the mask user guide.

2. From your HOME screen, push and hold for three seconds.

One of the following MASK FIT screens is displayed:

3. If necessary, adjust your mask, mask cushion and headgear until Mask Fit indicates Good.

After three minutes, the pressure reverts to the set pressure and treatment will begin. You can end

Mask Fit at any time by pressing .

1. From your HOME

screen, turn

until the RAMP

screen is displayed

in blue.

2. Press .

The selection is

highlighted in

orange.

3. Turn until the

ramp time you

require is displayed.

4. Press to

confirm your choice.

S9 Essentials

S9 Essentials is designed to make device interaction and menu navigation easier for you. If enabled by

the clinician, S9 Essentials disables the Info and Setup functionality so that you can simply start and stop

therapy and adjust ramp, humidification and Climate Control.

Selecting the mask type

To select your type of mask:

1. Press . The SETTINGS

screen is displayed.

2. Turn until Mask is

displayed in blue.

3. Press . The selection is

highlighted in orange.

4. Turn until the mask

setting that you require is

displayed.

5. Press to confirm your

choice.

6. Push to return to the

HOME screen.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ResMed Medizinische Geräte Handbücher

ResMed

ResMed AIRMINI Bedienungsanleitung

ResMed

ResMed C28173 Bedienungsanleitung

ResMed

ResMed Swift FX Bella Bedienungsanleitung

ResMed

ResMed AirFit F10 Bedienungsanleitung

ResMed

ResMed S8 ESCAPE System Bedienungsanleitung

ResMed

ResMed AcuCare F1-0 Bedienungsanleitung

ResMed

ResMed Swift FX Bella Gray Bedienungsanleitung

ResMed

ResMed Web-based Patient Monitor ResTraxx System Bedienungsanleitung

ResMed

ResMed Astral 150 Bedienungsanleitung

ResMed

ResMed airsense 10 autoset Montageanleitung

ResMed

ResMed Swift FX Bedienungsanleitung

ResMed

ResMed Mobi Bedienungsanleitung

ResMed

ResMed Mirage SoftGel Bedienungsanleitung

ResMed

ResMed Mirage FX Bedienungsanleitung

ResMed

ResMed Swift FX Bedienungsanleitung

ResMed

ResMed Mirage Swift II Bedienerhandbuch

ResMed

ResMed Lumis 100 VPAP S Bedienungsanleitung

ResMed

ResMed lumis series Bedienungsanleitung

ResMed

ResMed Astral Mobility bag Bedienungsanleitung

ResMed

ResMed AirFit N30 Bedienungsanleitung

ResMed

ResMed S9 VPAP Series Bedienungsanleitung

ResMed

ResMed AirFit P10 Montageanleitung

ResMed

ResMed VPAP III ST-A Bedienungsanleitung

ResMed

ResMed AirSense 10 Leitfaden

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung