Rockwell Automation Allen-Bradley 800G-XLS Z-EX Series Bedienungsanleitung

Installation Instructions

Original Instructions

Bulletin 800G Latch Mount Back-of-Panel Modules

Catalog Numbers

800G-XLS

-EX; 800G-DLSx-EX; 800G-DLSxXx-EX; 800G-APMC; 800G-XLSxZ-EX; 800G-DLSxZ-EX; 800G-DLSxXxZ-EX

Product Description

• Contact block (catalog number 800G-XLSx-EX)

Contact blocks are used withinhazardous areas wheremachine

functions are activated by pressing a button or actuating a

switch. These contact blocks are designed with self-cleaning

contacts and N.O. contacts feature positive break operation.

Contact blocks are compatible with all 800G non-illuminated

operators and the panel mount cover accessory (catalog

number 800G-APMC).

• Power module (catalog number 800G-DLSx-EX)

Power modules are used within hazardous areas to indicate the

functional status of respective machines visually by lighting up

or turning off. Power modules are compatible with all 800G

pilot light operators and the panel mount cover accessory

(catalog number 800G-APMC).

• Power module with contact block (catalog number

800GDLSxXx-EX)

Power module with contact block combination units are used

within hazardous areas where machine functions are activated

by depressing a push button and the corresponding functional

status is visually indicated. These units are compatible with all

800G illuminated push button operators and the panel mount

cover accessory (catalog number 800G-APMC).

ATTENTION: To help prevent electrical shock, disconnect from

power source before installing or servicing. Follow NFPA 70E

requirements. Install in suitableenclosure. Keep free from

contaminants.

Only suitably trained personnel can install, adjust, commission,

use, assemble, disassemble, and maintain the product in

accordance with applicable code of practice. If a malfunction or

damage occurs, do not attempt to repair the product.

IMPORTANT When working in hazardous areas, thesafety of personnel

and equipment depends on compliance with the relevant

safety regulations. The people in charge of installation and

maintenance bear a special responsibility. They must be

knowledgeable of the applicable rules andregulations.

These instructions provide a summary of the most important

installation measures. Everyone working with the product

mustreadtheseinstructionssothattheyarefamiliarwiththe

correct handling of the product.

Keep these instructions for future reference as they must be

available throughout the expected life of the product.

Contact Block (Screw Termination) Power Module (Screw Termination) Power Module with Contact Block

(Screw Termination)

Certifications

ATEX • Module: CML 17 ATEX 1107 U

• Module and cover: CML 17 ATEX 1118 X • Module: CML 17 ATEX 1108 U

• Module and cover: CML 17 ATEX 1118 X

IECEx • Module: IECEx CML 17.0047U

• Module and cover: IECEx CML 17.0056X • Module: IECEx CML 17.0048U

• Module and cover: IECEx CML 17.0056X

NEPSI • Module: GYJ17.1398U

• Module and cover: GYJ18.1084X • Module: GYJ17.1399U

• Module and cover: GYJ18.1084X

INMETRO • Module: UL-BR 14.0567U

• Module and cover: UL-BR 14.0568X • Module: UL-BR 14.0566U

• Module and cover: UL-BR 14.0568X

Gas Protection Type • Module: II 2 G Ex db eb IIC Gb

• Module and cover: II 2 G Ex db eb IIC T6 Gb

Dust Type (with 800G-APMC cover only) II 2 D Ex tb IIIC T80°C Db IP 66

Ambient Temperature Range -55…+40 °C (-67…+104 °F) @ 16 A

-55…+60 °C (-67…+140 °F) @ 11 A -55…+50 °C (-67…+122 °F) or 60 °C (140 °F) if Ue≤26.4V

Service Temperature Range -55…+85 °C (-67…+185 °F)

Mechanical and Electrical Ratings

Rated Insulation Voltage 690V 300V

Power Consumption — ≤1 W

Rated Voltage (Ue) AC 250V and 400V; DC24V and 110V Ta<50 °C (122 °F): 12…250V AC, 12…60V DC

Ta<60 °C (140 °F): 12…24V AC/DC

Illumination Colors (LED) — Red, green, blue, white, or yellow

Contact Options 1 N.O./1 N.C., 2 N.O., 2 N.C. — 1 N.O., 1 N.C.

Utilization Category (AC) AC-12: 16 A, 400V; AC-15: 10 A, 400V — AC-15: 1 A, 230V

Utilization Category (DC) DC-13: 1 A, 24V; DC-13: 0.5 A, 110V — DC-13: 0.25 A, 24V

Conventional Thermal Current (Ithe)16 A/40 °C (104 °F)

11 A/60 °C (140 °F) ——

Conductor Size 0.75 - 2.5 mm² (18…14 AWG)

Degree of Protection IP20 (module only); IP64/IP66 (module and operator); IP66/IP67 (module, operator, and cover)

2Rockwell Automation Publication 800G-IN003B-EN-P -May 2018

Bulletin 800G Latch Mount Back-of-Panel Modules

Additional Contact Block and Power Module

Information

Front-of-panel operators are inserted into a mounting hole in an “Ex e”

enclosure or control panel. The respective back-of-panel module is

connected to the operator using a bayonet lock.

The conductor connection is made by wiring the conductors to

terminals at the back of the contact block, power module, or power

module with contact block combination unit.

Panel Mount Cover (Catalog Number 800G-APMC)

The panel mount cover accessory allows a conductor

cable to be connected to the latch mount contact block,

power module, or power module with contact block

combination unit through a cable gland. The cover

provides an increased ingress protection (IP) rating and

is connected to the back-of-panel component by tightening two screws.

Compatibility

Contact blocks, power modules, and power module with contact block

combination units are compatible with specific front-of-panel

operators.

Safety Instructions

Improper installation can cause malfunctioning and the loss of

explosion protection.

All back-of-panel modules and operators can only be used within the

specified ambient temperature range (depending on the voltage and

current).

Use in areas other than those areas specified or the modification of the

product by anyone other than the manufacturer is not permitted and

exempts Rockwell Automation from liability for defects and any

further liability.

The applicable statutory rules and other binding directives that relate

to workplace safety, accident prevention, and environmental

protection must be observed.

Before you commission or restart operation, check compliance with all

applicable laws and directives.

All back-of-panel modules can be used only if they are in a clean and

undamaged condition. Do not modify these modules in any way.

Special Conditions for Safe Use

The contact block, power module, and power module with contact

block devices must be installed in a manner that protects against

mechanical damage and electrostatic charges.

Standards Conformed To

Assemble, Install, and Commission

• Only qualified personnel are allowed to assemble, disassemble,

install, and commission the device.

• Protect devices against mechanical damage or electrostatic

discharge.

• Use suitable tools and install cable firmly.

• Use cable that is rated with an appropriate temperature range

suitable for the application.

Assemble and Disassemble — Modules

To mount the contact block or

power module, follow these steps:

1. Verify that the contact

block or power module is

intact (no cracks).

2. Confirm the back-of-panel module is compatible with the

installed operator (see Compatibility).

3. Position the bayonet lock facing toward the mounted front-of-

panel operator.

4. Turn the locking bolt to secure the contact block or power

module to the front-of-panel operator.

Installation — Modules

In hazardous areas, the contact block or power module must be used:

• In appropriate enclosures with “Ex e” increased safety type of

protection. The clearance and creepage distances under IEC/

EN 60079-7 Clauses 4.3 and 4.4 must be observed.

• In an enclosure that corresponds to another approved type of

protection that is specified in IEC/EN 60079-0 Clause 1.

Configured Catalog Number (Installed)

Cat. No. Components

800G-XLSxZ-EX 800G-XLSx-EX + 800G-APMC

800G-DLSxZ-EX 800G-DLSx-EX + 800G-APMC

800G-DLSxXxZ-EX 800G-DLSxXx-EX + 800G-APMC

Back-of-Panel Front-of-Panel

Contact block Non-illuminated operator

Power module Pilot light

Power module and contact block Illuminated push button

Contact Block, Power Module, and Power Modules with Contact Block Components

• EN 60079-0 • EN 60079-1 • EN 60079-7

• IEC 60079-0 • IEC 60079-1 • IEC 60079-7

Back-of-Panel Components with Panel Mount Cover Accessory Installed

• EN 60079-0 • EN 60079-1 • EN 60079-7 • EN-60079-31

• IEC 60079-0 • IEC 60079-1 • IEC 60079-7 • IEC 60079-31

ATTENTION: Risk of serious injury due to incorrect assembly,

installation, and commissioning.

IMPORTANT The components that are pictured within this publication

serve as an example of all back-of-panel modules.

“Click”

Rockwell Automation Publication 800G-IN003B-EN-P -May 2018 3

Bulletin 800G Latch Mount Back-of-Panel Modules

Take care when following these steps to connect the cable:

1. Strip 40 mm (1.575 in.) of sheath off the cable.

2. Remove approximately 6 mm (0.236 in.) of insulation from the

conductors.

3. Prepare the ends of the fine-stranded and multi-stranded

conductors. Crimp wire end sleeves with suitable crimp tools.

Connection cross-sections: 0.75…2.5 mm (18…14 AWG).

4. Open terminal cage and insert conductors.

5. Tighten the terminals to a torque range of 0.4…0.7 N·m

(3.5…6.2 lb·in).

Assemble/Disassemble — Panel Mount Cover

To install the panel mount cover, follow these steps:

1. Verify that the cover and the fitted sealing are intact (no

cracks).

2. Install the sealing gasket (1) with the round side

facing downwards into the groove of the back-of-

panel device.

3. Strip 40 mm (1.575 in.) sheath from the cable

and remove approx. 6 mm (0.236 in.) insulation

from the conductors.

4. Open the sealing nut (2) enough to allow

the cable to be inserted.

5. Feed the cable (3) into the cable gland on

the cover until there is sufficient length

available for preparing the cable connection.

6. Close the sealing nut (2).

7. Connect the conductors (4) as

shown in Installation — Modules.

8. Push the panel mount cover

firmly onto the contact block, power

module, or power module with contact

block combination unit.

9. Tighten the screws (5) with a torque of

0.5…0.6 N·m (4.4…5.3 lb·in).

10. Tighten the sealing nut (6) with a torque

of 1.3 N·m / 11.5 lb·in (lock nut (7) has a

max. torque of 0.6 N·m / 5.3 lb·in).

11. If necessary, remove the label (8), mark it,

and reinstall.

Commissioning — Cover and Modules

Before commissioning, check the following:

• The device has been installed in compliance with regulations.

• The device is not damaged.

• The connection has been established properly (verify that the

conductors are secure).

Maintenance

• Only qualified personnel are allowed to do any maintenance

and fault clearance.

• IEC/EN 60079-17 must be observed.

You must keep the contact block, power module, and panel mount

cover devices in good condition, operate them properly, monitor them,

and clean them regularly.

• Check all contact blocks, power modules, panel mount covers,

and cables regularly for cracks and damage. Verify that they are

properly installed.

Repair and Replacement

• Back-of-panel devices are defective if the contact block does

not function properly or the status indicator does not

illuminate on the power module.

• Devices must be replaced with an equivalent catalog number

from the manufacturer.

• Panel mount covers are defective if they are damaged or if the

cable no longer fits securely to maintain IP rating.

Accessories and Replacement Parts

For more accessories and replacement parts that Rockwell Automation

offers, see https://ab.rockwellautomation.com/Push-Buttons/

Hazardous-Location/800G.

Terminals

Contact Block

1 N.O. and 1 N.C. Contact 2 N.C. Contacts 2 N.O. Contacts

Power Module Power Module with Contact Block

1 N.O. 1 N.C.

ATTENTION: Risk of serious injury due to incorrect maintenance.

IMPORTANT Do not clean contact blocks, power modules, or power

module with contact block combination units with

compressed air.

ATTENTION: Defective contact blocks, power modules, and panel

mount covers cannot be repaired; they must be replaced.

Allen-Bradley, Rockwell Automation, and Rockwell Software are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E BlokKat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400

Rockwell Automation maintains current product environmental information on its website at

http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.

EEE Yönetmeligine Uygundur.

Publication 800G-IN003B-EN-P - May 2018 10001129318 Ver 02

Disposal

At the end of its life, this equipment must be collected separately from

any unsorted municipal waste. Follow all local and national

requirements for disposal of this product.

Approximate Dimensions

Dimensions are shown in millimeters (inches).

Declaration of Conformity

Rockwell Automation, Inc. declares that the 800G-XLSx-EX,

800GDLSx-EX, and 800G-DLSxXx-EX Series A latch mount

contact blocks, power modules, and power module with contact block

units are in compliance with Essential Health and Safety Requirements

of Directive 2014/34/EU (ATEX) as follows:

• Equipment Group II, Equipment Category 2

• Type of Protection “Ex db eb IIC Gb”

• Compliance to standards EN 60079-0:2012+A11:2013,

EN 60079-1:2014, and EN 60079-7: 2015 per ATEX Type

Examination Certificates CML 17ATEX1107U and

CML 17ATEX1108U

Hereby, Rockwell Automation, Inc. declares that the 800G-XLS*Z-

EX, 800G-DLS*Z-EX, and 800G-DLS*X*Z-EX Series A latch mount

contact blocks, power modules, and power module with contact block

units with the panel mount cover accessory installed (800G-APMC)

are in compliance with Essential Health and Safety Requirements of

Directive 2014/34/EU (ATEX) as follows:

• Equipment Group II, Equipment Category 2

• Type of Protection “Ex db eb IIC Gb / Ex tb IIIC T80°C

Db IP66”

• Compliance to standards EN 60079-0:2012+A11:2013,

EN 60079-1:2014, EN 60079-7: 2015, and

EN 60079-31: 2014 per ATEX Type Examination Certificates

CML 17ATEX1118X

The full text of the EU declarations of conformity is available at the

following website:

http://www.rockwellautomation.com/global/certification

Contact Block (Cat. No.800G-XLSx-EX) Power Module (Cat. No. 800G-DLSx-EX)

Power Module with Contact Block (Cat. No.800G-DLSxXx-EX)

Panel Mount Cover

(Cat. No. 800G-APMC)

Panel Mount Cover and Panel Mount

Contact Block (Cat. No. 800G-XLSxZ-EX)

68 (2.7)

Ø 19

(0.75)

68 (2.7)

Ø 19

(0.75)

(2.8)

38 (1.5)

57 (2.24)

76.5

(3)

(2.8)

38 (1.5)

104 (4.1)

Panel MountCover and Panel Mount

Power Module (Cat. No. 800G-DLSxZ-EX)

Panel MountCover and Panel Mount Power

Module with Contact Block

(Cat. No. 800G-DLSxXxZ-EX)

136 (5.35)

130 (5.1)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockwell Automation Steuereinheit Handbücher

Rockwell Automation

Rockwell Automation Allen-Bradley Guardmaster MSR41 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1746-BTM Bedienungsanleitung

Rockwell Automation

Rockwell Automation Reliance electric GV3000/SE Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ArmorBlock 1732E-IB8M8SOER Bedienungsanleitung

Rockwell Automation

Rockwell Automation Micro800 2080-MEMBAK-RTC Bedienungsanleitung

Rockwell Automation

Rockwell Automation ControlLogix 1756-HYD02 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1441-DYN25-MBAL Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 193-EGJ Series Benutzerhandbuch

Rockwell Automation

Rockwell Automation Trusted CS300 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLERED20Y Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 800G-XBx-EX Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-MVI Bedienungsanleitung

Rockwell Automation

Rockwell Automation CENTERLINE 2100 LVMCC Bedienungs- und Wartungshandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley ControlNet 1734-ACNR Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1770-KFC15 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted TMR Expander Interface Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley SynchLink 1751-SLBA Bedienungsanleitung

Rockwell Automation

Rockwell Automation Micro800 Series Handbuch

Rockwell Automation

Rockwell Automation ControlLogix 1756-M02AE Gebrauchsanweisung

Rockwell Automation

Rockwell Automation 2711P-RPA Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Guard I/O DeviceNet 1732DS-IB8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation ControlLogix 1756-EN2TR Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-HSC Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLSBATASSY3 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung