Rockwell Automation Allen-Bradley 1441-DYN25-MBAL Bedienungsanleitung

User Manual

Balancing Extension Module for the Dynamix 2500

Data Collector

Catalog Number

1441-DYN25-MBAL

Important User Information

Solid-state equipment has operational characteristics differing from those of electromechanical equipment. Safety

Guidelines for the Application, Installation and Maintenance of Solid State Controls (publication SGI-1.1 available from

your local Rockwell Automation sales office or online at http://www.rockwellautomation.com/literature/) describes some

important differences between solid-state equipment and hard-wired electromechanical devices. Because of this difference,

and also because of the wide variety of uses for solid-state equipment, all persons responsible for applying this equipment

must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from

the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and

requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or

liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or

software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation,

Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

Allen-Bradley, Rockwell Software, Rockwell Automation, Dynamix, Enpac, Emonitor, and TechConnect are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous

environment, which may lead to personal injury or death, property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death,

property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the

consequence

SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that

dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that

surfaces may reach dangerous temperatures.

IMPORTANT

Identifies information that is critical for successful application and understanding of the product.

Rockwell Automation Publication 1441-UM004A-EN-P - May 2011 3

Table of Contents

Preface

Optional Extension Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Chapter 1

Installing Optional Extension

Modules

Install Extension Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Uninstall Extension Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Manage Extension Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Extension Module Battery Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . 13

Chapter 2

Balancing Extension Module

Balancing Measurements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Plane Balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Static-couple Balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Set Up the Balancing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Balance Setup Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Single Plane Balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Single Plane Balancing Procedure Overview. . . . . . . . . . . . . . . . . . . . . 26

Take the Initial Vibration Measurement. . . . . . . . . . . . . . . . . . . . . . . . 27

Add the Trial Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Enter the Trial Weight Manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Estimate the Trial Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Take a Trial Run Weight Measurement . . . . . . . . . . . . . . . . . . . . . . . . 32

Take a Correction Run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Perform a Trim Run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Add the Correction Weight and Take a Residual Measurement . . 41

Two Plane Balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Two Plane Balancing Procedure Overview. . . . . . . . . . . . . . . . . . . . . . 46

How to Set Up a Two-Plane Procedure . . . . . . . . . . . . . . . . . . . . . . . . 46

How to Perform Two-plane Balancing . . . . . . . . . . . . . . . . . . . . . . . . . 50

Move Around in a Balance Run. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Saving, Loading, and Reviewing Balance Measurements . . . . . . . . . . . . . 61

Save a Balance Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Load a Previously Saved Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Review Balancing Measurements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

How to Delete Stored Files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Index

4Rockwell Automation Publication 1441-UM004A-EN-P - May 2011

Table of Contents

Notes:

Rockwell Automation Publication 1441-UM004A-EN-P - May 2011 5

Preface

This manual describes the Balancing extension module for the Dynamix 2500

data collector. You install the extension module with the Balancing Secure Digital

(SD) card.

See Installing Optional Extension Modules on page 7 for installation

instructions.

The balancing test determines the amount and location of the heavy spot on a

rotating shaft so that you can balance it with an equal amount of weight in the

opposite direction.

There are three types of measurements in the balancing process:

•Initial Vibration

•Trial Weight

•Residual Measurements

Optional Extension

Modules

These are the optional extension modules for the Dynamix 2500 data collector:

•1441-DYN25-4C, 4-channel Activation (1)

The 4-channel activation lets you take 3- and 4-channel magnitude, time

waveform, spectra, and Offroute measurements.

•1441-DYN25-MBMP Bump Test

A bump test (or hammer test) determines the natural frequencies of a

machine or a structure.

•1441-DYN25-MBAL Balancing

Balancing application resolves single-plane, two-plane, and static-couple

balances with high precision.

•1441-DYN25-MFRF Frequency Response Function

The FRF test lets you determine the natural frequencies of a machine as

well as sophisticated information about the frequency response of the

structure being tested.

•1441-DYN25-MREC Time Recorder

The Time Recorder test uses a the instrument as a data recorder for real-

time data acquisition and analysis.

•1441-DYN25-MRUC Run Up Coast Down

The RUCD test records and analyzes data from intermittent events and

transient vibration signals from non-steady state machines.

See Additional Resources on page 6 for a listing of available publications.

(1) This is an activation license for the Dynamix 2500 data collector.

6Rockwell Automation Publication 1441-UM004A-EN-P - May 2011

Preface

Additional Resources

These documents contain additional information concerning related products

from Rockwell Automation.

You can view or download publications at

http://www.rockwellautomation.com/literature. To order paper copies of

technical documentation, contact your local Allen-Bradley distributor or

Rockwell Automation sales representative.

Resource Description

Dynamix 2500 Data Collector User Manual,

publication 1441-UM001 Describes the Dynamix 2500 data collector

which provides predictive maintenance by

using noise and vibration analysis.

Bump Test Extension Module for the Dynamix 2500

Data Collector User Manual,

publication 1441-UM002

Describes how determine natural (or resonant)

frequencies of a machine or structure.

Frequency Response Function Extension Module

for the Dynamix 2500 Data Collector User Manual,

publication 1441-UM003

Describes how to determine the natural

frequencies of a machine or structure by using

modal hammer.

Time Recorder Extension Module for the Dynamix

2500 Data Collector User Manual,

publication 1441-UM005

Describes how to use the data collector as a

data recorder for real-time data acquisition,

post processing, and analysis.

Run Up Coast Down Extension Module for the

Dynamix 2500 Data Collector User Manual,

publication 1441-UM006

Describes how to record and analyze data from

intermittent events and transient vibration

signals from non-steady state machines.

Emonitor User’s Guide, publication

EMONTR-UM001

Describes data management for predictive

maintenance services.

Dynamix 2500 Data Collector Kit Release Notes,

publication 1441-RN001 Provides information on the latest updates, for

example, firmware, certifications, warnings,

and hardware changes for the data collector.

Dynamix 2500 Data Collector Optional Extension

Modules Release Notes, publication 1441-RN002 Provides information on how to install the

Optional Extension Modules on to the Dynamix

2500 data collector.

Industrial Automation Wiring and Grounding

Guidelines, publication 1770-4.1 Provides general guidelines for installing a

Rockwell Automation industrial system.

Product Certifications website, http://www.ab.com Provides declarations of conformity,

certificates, and other certification details.

Rockwell Automation Publication 1441-UM004A-EN-P - May 2011 7

Chapter

Installing Optional Extension Modules

The data collector uses the Extension Manager to install and uninstall extension

modules. These extension modules are licensed and ordered separately from the

basic entry-level product.

Install Extension Modules

The installation Secure Digital (SD) cards that you receive work with any

Dynamix 2500 data collector. Once you have installed an extension module, the

card is locked so that it can only be used with that instrument.

You can uninstall extension modules if required. When uninstalling an extension

module, you have the option to free up the license so you can install the extension

module on another instrument. This makes the extension module available to be

transferred between units.

Follow these instructions to install an extension module.

1. Open the base cover at the bottom of the Dynamix 2500 data collector.

2. Place the extension module SD card contact side-up into the unit until it is

firmly seated in place.

3. Close the base cover.

Topic Page

Install Extension Modules 7

Uninstall Extension Modules 9

Manage Extension Modules 12

Extension Module Battery Status Indicators 13

IMPORTANT

One installation SD card is required for each instrument that needs to

be upgraded.

IMPORTANT

When ever you re-run the OS Loader software, you will re-load only the

main OS firmware. The OS loader will backup licence files and data, but

not the optional extension modules. Once you have updated the OS

firmware, insatll the latest version of your optional extension modules.

See the Dynamix 2500 Data Collector User Manual, 1441-UM001, for

more information.

8Rockwell Automation Publication 1441-UM004A-EN-P - May 2011

Chapter 3 Installing Optional Extension Modules

4. Apply power to the data collector.

5. From the Main Menu, select Setup Utility and press Enter.

6. Press 0 (Shift) to display the second set of functions.

The Extension Manager function remains on the screen for about three

seconds after releasing 0 (Shift).

7. Press F1 (Extn Mgr).

The Extension Manager screen appears showing the current extension

module installations.

8. Press 0 (Shift) to display the Install Extension function.

9. Press F2 (Install) to install the new extension module.

Extension Manager

Rockwell Automation Publication 1441-UM004A-EN-P - May 2011 9

Installing Optional Extension Modules Chapter 3

When the installation is complete, a confirmation prompt appears.

10. Press F4 (OK).

The new extension module appears in the list.

11. Press F4 (Esc) to exit the Extension Manager screen.

Uninstall Extension

Modules

Follow these instructions to uninstall an extension module.

1. Press 0 (Shift) from the Setup Utility screen to display the Extension

Manager function.

The Extension Manager function remains on the screen for about three

seconds after releasing 0 (Shift).

2. Press F1 (Extn Mgr).

Extension Manager

10 Rockwell Automation Publication 1441-UM004A-EN-P - May 2011

Chapter 3 Installing Optional Extension Modules

The Extension Manager screen appears.

3. Select the extension module you want to uninstall and press F3 (Select).

F3 (Select) toggles the selection on and off.

A checkmark appears next to that extension module.

4. Press F1 (Uninstall).

This screen lists the

extension modules

currently installed and the

on the unit.

Inhaltsverzeichnis

Andere Rockwell Automation Steuereinheit Handbücher

Rockwell Automation

Rockwell Automation Allen-Bradley SLC ControlNet 1747-SCNR Bedienungsanleitung

Rockwell Automation

Rockwell Automation D2-3563 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley SLC 500 BASIC Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley B Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1794-OB8EPXT Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlNet 1734-ACNR Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1797-IE8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation MAO04NND Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1768-L43 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted TMR 120 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1770-KFC15 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted CS300 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-IB16ISOE Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Guard I/O DeviceNet 1732DS-IB8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1756-HIST1G Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 800G-XLS Z-EX Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley XM-124 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-OF4 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1734-OE4C Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1756-EWEB Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley IntelliVAC Bedienungsanleitung

Rockwell Automation

Rockwell Automation CENTERLINE 2100 LVMCC Bedienungs- und Wartungshandbuch

Rockwell Automation

Rockwell Automation 1794-OB8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ArmorBlock 1732E-IB8M8SOER Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung