Rockwell Automation 1794-OB8 Bedienungsanleitung

Installation Instructions

FLEX I/O Digital DC Output Modules

Catalog numbers 1794-OB8, 1794-OB8EP, 1794-OB16,

1794-OB16P, 1794-OB32P

Table of Contents

Topic Page

Important User Information 2

Environment and Enclosure 3

Preventing Electrostatic Discharge 3

European Hazardous Location Approval 3

North American Hazardous Location Approval 7

Install Your FLEX I/O AC Digital Output Module 8

Connect Wiring for 1794-OB8, 1794-OB8EP, 1794-OB16, and 1794-OB16P 9

Connect Wiring for the 1794-OB32P 11

Configuring your 1794-OB8EP Output Module 14

Configure the 1794-OB8, 1794-OB16, 1794-OB16P, 1794-OB32P Modules 15

Specifications 16

2FLEX I/O Digital DC Output Modules

Publication 1794-IN094D-EN-P - July 2018

Important User Information

Solid-state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation, and Maintenance of Solid-State Controls

(Publication SGI-1.1 available from your local Rockwell Automation Sales Office or online at

http://www.rockwellautomation.com/literature/) describes some important differences between solid

state equipment and hard-wired electromechanical devices. Because of this difference, and also because

of the wide variety of uses for solid state equipment, all persons responsible for applying this equipment

must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc. is prohibited.

Throughout this manual we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or death,

property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to

personal injury or death, property damage, or economic loss. Attentions help you

identify a hazard, avoid a hazard, and recognize the consequences.

IMPORTANT Identifies information that is critical for successful application and understanding of

the product.

FLEX I/O Digital DC Output Modules 3

Publication 1794-IN094D-EN-P - July 2018

Environment and Enclosure

Preventing Electrostatic Discharge

ATTENTION: This equipment is intended for use in a Pollution Degree 2

industrial environment, in overvoltage Category II applications (as defined in

EN/IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating.

This equipment is not intended for use in residential environments and may not

provide adequate protection to radio communication services in such

environments.

This equipment is supplied as open-type equipment for indoor use. It must be

mounted within an enclosure that is suitably designed for those specific

environmental conditions that will be present and appropriately designed to

prevent personal injury resulting from accessibility to live parts. The enclosure

must have suitable flame-retardant properties to prevent or minimize the spread

of flame, complying with a flame spread rating of 5VA or be approved for the

application if nonmetallic. The interior of the enclosure must be accessible only

by the use of a tool. Subsequent sections of this publication may contain more

information regarding specific enclosure type ratings that are required to

comply with certain product safety certifications.

In addition to this publication, see the following:

• Industrial Automation Wiring and Grounding Guidelines, publication

1770-4.1, for more installation requirements.

• NEMA Standard 250 and EN/IEC 60529, as applicable, for explanations of

the degrees of protection provided by enclosures.

ATTENTION: This equipment is sensitive to electrostatic discharge, which can

cause internal damage and affect normal operation. Follow these guidelines

when you handle this equipment:

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wriststrap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• Use a static-safe workstation, if available.

• Store the equipment in appropriate static-safe packaging when not in use.

4FLEX I/O Digital DC Output Modules

Publication 1794-IN094D-EN-P - July 2018

ATTENTION: This product is grounded through the DIN rail to chassis ground.

Use zinc plated chromate-passivated steel DIN rail to assure proper grounding.

The use of other DIN rail materials (for example, aluminum or plastic) that can

corrode, oxidize, or are poor conductors, can result in improper or intermittent

grounding. Secure DIN rail to mounting surface approximately every 200 mm

(7.8 in.) and use end-anchors appropriately. Be sure to ground the DIN rail

properly.

Refer to Industrial Automation Wiring and Grounding Guidelines, Rockwell

Automation publication 1770-4.1, for more information.

ATTENTION: If this equipment is used in a manner not specified by the

manufacturer, the protection provided by the equipment may be impaired.

ATTENTION: If this equipment is used in a manner not specified by the

manufacturer, the protection provided by the equipment may be impaired.

ATTENTION: Read this document and the documents listed in the Additional

Resources section about installation, configuration, and operation of this

equipment before you install, configure, operate, or maintain this product.

Users are required to familiarize themselves with installation and wiring

instructions in addition to requirements of all applicable codes, laws, and

standards.

ATTENTION: Installation, adjustments, putting into service, use, assembly,

disassembly, and maintenance are required to be carried out by suitably

trained personnel in accordance with applicable code of practice.

In case of malfunction or damage, no attempts at repair should be made. The

module should be returned to the manufacturer for repair. Do not dismantle the

module.

ATTENTION: Use only a soft dry anti-static cloth to wipe down equipment. Do

not use any cleaning agents.

FLEX I/O Digital DC Output Modules 5

Publication 1794-IN094D-EN-P - July 2018

WARNING: When you insert or remove the module while backplane power

is on, an electric arc can occur. This could cause an explosion in hazardous

location installations.

Be sure that power is removed or the area is nonhazardous before

proceeding. Repeated electric arcing causes excessive wear to contacts on

both the module and its mating connector. Worn contacts may create

electrical resistance that can affect module operation.

WARNING: If you insert or remove the module while backplane power is on,

an electric arc can occur. This could cause an explosion in hazardous location

installations.

Be sure that power is removed or the area is nonhazardous before

proceeding.

At the end of its life, this equipment should be collected separately from any

unsorted municipal waste.

6FLEX I/O Digital DC Output Modules

Publication 1794-IN094D-EN-P - July 2018

European Hazardous Location Approval

Approved for 1794-OB8, 1794-OB8EP, 1794-OB16 and 1794-OB16P modules..

The following applies to products marked II 3 G:

Are Equipment Group II, Equipment Category 3, and comply with the Essential Health and

Safety Requirements relating to the design and construction of such equipment given in

Annex II to EU Directive 2014/34/EU. See the EU Declaration of Conformity at

http://www.rockwellautomation.com/global/certification/overview.page for details.

The type of protection is II 3G Ex nA IIC T3 Gc according to EN 60079-15.

Comply to Standards EN 60079-0:2012, EN 60079-15:2010, reference certificate number

LCIE 01 ATEX 6020 X.

Are intended for use in areas in which explosive atmospheres caused by gases, vapors,

mists, or air are unlikely to occur, or are likely to occur only infrequently and for short

periods. Such locations correspond to Zone 2 classification according to ATEX directive

2014/34/EU.

WARNING: Observe the following additional certification requirements:

• This equipment is not resistant to sunlight or other sources of

UV radiation.

• This equipment shall be mounted in an ATEX/IECEx Zone 2 certified

enclosure with a minimum ingress protection rating of at least IP54 (in

accordance with EN/IEC 60079-15) and used in an environment of not

more than Pollution Degree 2 (as defined in EN/IEC 60664-1) when

applied in Zone 2 environments. The enclosure must be accessible only by

the use of a tool.

• This equipment shall be used within its specified ratings defined by

Rockwell Automation.

• The instructions in the user manual shall be observed.

• This equipment must be used only with ATEX certified Rockwell

Automation backplanes.

• Earthing is accomplished through mounting of modules on rail.

• Devices shall be used in an environment of not more than Pollution

Degree 2.

• Enclosure must be marked with the following: “Warning - Do not open

when energized.” After installation of equipment into the enclosure,

access to termination compartments shall be dimensioned so that

conductors can be readily connected.

FLEX I/O Digital DC Output Modules 7

Publication 1794-IN094D-EN-P - July 2018

North American Hazardous Location Approval

The 1794-OB8, 1794-OB8EP, 1794-OB16, 1794-OB16P module is Hazardous Location approved:

The following information applies when

operating this equipment in hazardous locations:

Informations sur l’utilisation de cet équipement

en environnements dangereux:

Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for

use in Class I Division 2 Groups A, B, C, D, Hazardous

Locations and nonhazardous locations only. Each product is

supplied with markings on the rating nameplate indicating

the hazardous location temperature code. When combining

products within a system, the most adverse temperature

code (lowest "T" number) may be used to help determine

the overall temperature code of the system. Combinations

of equipment in your system are subject to investigation by

the local Authority Having Jurisdiction at the time of

installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne

conviennent qu'à une utilisation en environnements de Classe

I Division 2 Groupes A, B, C, D dangereux et non dangereux.

Chaque produit est livré avec des marquages sur sa plaque

d'identification qui indiquent le code de température pour les

environnements dangereux. Lorsque plusieurs produits sont

combinés dans un système, le code de température le plus

défavorable (code de température le plus faible) peut être

utilisé pour déterminer le code de température global du

système. Les combinaisons d'équipements dans le système

sont sujettes à inspection par les autorités locales qualifiées

au moment de l'installation.

WARNING:

EXPLOSION HAZARD

• Do not disconnect equipment unless

power has been removed or the area is

known to be nonhazardous.

• Do not disconnect connections to this

equipment unless power has been

removed or the area is known to be

nonhazardous. Secure any external

connections that mate to this equipment

by using screws, sliding latches,

threaded connectors, or other means

provided with this product.

• Substitution of components may impair

suitability for Class I, Division 2.

WARNING:

RISQUE D’EXPLOSION

• Couper le courant ou s'assurer que

l'environnement est classé non dangereux

avant de débrancher l'équipement.

• Couper le courant ou s'assurer que

l'environnement est classé non dangereux

avant de débrancher les connecteurs. Fixer

tous les connecteurs externes reliés à cet

équipement à l'aide de vis, loquets

coulissants, connecteurs filetés ou autres

moyens fournis avec ce produit.

• LLa substitution de composants peut rendre

cet équipement inadapté à une utilisation en

environnement de Classe I, Division 2.

8FLEX I/O Digital DC Output Modules

Publication 1794-IN094D-EN-P - July 2018

Install Your FLEX I/O AC Digital Output Module

The module mounts on a 1794 terminal base.

1. Rotate the keyswitch (3) on the terminal base (4) clockwise to position 2 as

required for this type of module.

2. Make sure the Flexbus connector (1) is pushed all the way to the left to connect

with the neighboring terminal base/adapter.

You cannot install the module unless the connector is fully extended.

3. Make sure the pins on the bottom of the module are straight so they will align

properly with the connector in the terminal base.

4. Position the module (7) with its alignment bar (6) aligned with the groove (5) on

the terminal base.

5. Press firmly and evenly to seat the module in the terminal base unit. The module

is seated when the latching mechanism (2) is locked into the module.

Description Description

1 Flexbus connector 5 Groove

2 Latching mechanism 6 Alignment bar

3 Keyswitch 7 Module

4 Terminal base

FLEX I/O Digital DC Output Modules 9

Publication 1794-IN094D-EN-P - July 2018

Connect Wiring for 1794-OB8, 1794-OB8EP, 1794-OB16, and 1794-OB16P

1. Connect individual output wiring to numbered terminals on the 0-15 row (A) as

indicated in the table below 1794-OB8 – Terminals 0...7; 1794-OB16 and

1794-OB16P – terminals 0...15; 1794-OB8EP – even numbered terminals

0...14.

2. Connect the associated -V output common to the corresponding terminal on the

16…33 row (B) for each output as indicated in the table below. Commons are

internally connected together.

1794-OB8EP – connect associated output common to odd-numbered terminals

on row A or associated terminals on row (B).

3. Connect +V DC power to terminal 34 on the 34…51 row (C).

4. Connect -V DC common to terminal 16 on the 16…33 row (B).

5. If daisychaining power to the next terminal base, connect a jumper from terminal

51 (+V DC) on this base unit to terminal 34 on the next base unit.

6. If continuing -V DC common to the next base unit, connect a jumper from

terminal 33 (common) on this base unit to terminal 16 on the next base unit.

Wiring Connections for 1794-OB8, 1794-OB16, and 1794-OB16P

used with 1794-TB2, 1794-TB3, or 1794-TB3S Terminal Base Unit

Output(1)

(1) 1794-OB8 – Outputs 0...7; 1794-OB16 and 1794-OB16P – Outputs 0...15

Output Terminal Common Terminal

Output 0 A-0 B-17

Output 1 A-1 B-18

Output 2 A-2 B-19

Output 3 A-3 B-20

Output 4 A-4 B-21

Output 5 A-5 B-22

Output 6 A-6 B-23

Output 7 A-7 B-24

Output 8 A-8 B-25

Output 9 A-9 B-26

Output 10 A-10 B-27

Output 11 A-11 B-28

Output 12 A-12 B-29

Output 13 A-13 B-30

Output 14 A-14 B-31

Output 15 A-15 B-32

+V DC C-34…C-51 (C-34 and C-51 for 1794-TB2)

Common B-16…B-33

10 FLEX I/O Digital DC Output Modules

Publication 1794-IN094D-EN-P - July 2018

1794-TB2, 1794-TB3, and 1794-TB3S Terminal Base Wiring for 1794-OB8,

1794-OB8EP, 1794-OB16, and 1794-OB16P

Wiring Connections for 1794-OB8EP

1794-TB2, 1794-TB3, 1794-TB3S 1794-TBN

Output Output Terminal Common

Terminal(1)

Output Terminal Common

Terminal(2)

Output 0 A-0 A-1/B-17 B-0 C-1

Output 1 A-2 A-3/B-18 B-2 C-3

Output 2 A-4 A-5/B-19 B-4 C-5

Output 3 A-6 A-7/B-20 B-6 C-7

Output 4 A-8 A-9/B-21 B-8 C-9

Output 5 A-10 A-11/B-22 B-10 C-11

Output 6 A-12 A-13/B-23 B-12 C-13

Output 7 A-14 A-15/B-24 B-14 C-15

+V DC C-34…C-51 (C-34 and C-51 for 1794-TB2, 1794-TBN)

Common B-16…B-33 (B-16 and B-33 for 1794-TBN)

(1) 1794-TB2, 1794-TB3,1794 -TB3S – A-1, A-3, A-5, A-7, A-9, A-11, A-13, and A-15 are connected together inside the

module to 24V DC common.

(2) 1794-TBN – C-1, C-3, C-5, C-7, C-9, C-11, C-13, and C-15 are connected together inside the module to 24V DC common.

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51

Outputs

Commons

(1794-TB3 shown)

Connect -V (Supply Common) to terminal B-16

Connect +V (Supply +Voltage) to terminal C-34

-V

Voltage

In +V

Voltage

Out +V

Voltage

Terminals 35 thru 50 not available on 1794-TB2

Common

-V

Common

(Use B-33 and C-51 for daisy-chaining to next terminal base unit.)

Total current draw through the terminal base is limited to 10A. Separate power

connections to each terminal base may be necessary.

Andere Handbücher für 1794-OB8

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockwell Automation Steuereinheit Handbücher

Rockwell Automation

Rockwell Automation Allen-Bradley 1794-OB8EPXT Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLBRED20 SER B Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted CS300 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1734-OE4C Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix B Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation 2711P-RPA Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix DeviceNet... Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Guard I/O DeviceNet 1732DS-IB8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-HSC Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 800G-XLS Z-EX Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley MSR42 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley FactoryTalk Analytics LogixAI Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1797-IE8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlNet 1734-ACNR Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1756-EWEB Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1756-EN2TSC Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley FactoryTalk Historian ME Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 794-IRT8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLERED Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-MVI Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1756-ENBT Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Compact GuardLogix 5370... Benutzerhandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley 193-EGJ Series Benutzerhandbuch

Rockwell Automation

Rockwell Automation ArmorBlock MaXum 1792D-8BT8PE Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung