Rockwell Automation ArmorBlock MaXum 1792D-8BT8PE Bedienungsanleitung

Publication 1792D-IN055A-EN-P - October 2004

Installation Instructions

ArmorBlock MaXum 8 Input / 8 Output Module

With Ground Lug

Cat. No. 1792D-8BT8PE

This ArmorBlock MaXum

I/O module (Cat. No. 1792D-8BT8PE) is a

stand-alone 24V dc I/O product, which communicates via a

DeviceNet

network. The sealed housing of this module requires no

enclosure.

This module has 8 inputs and 8 outputs accessed through Y splitter

cables. Inputs are 24V dc devices. Eight self-protected 24V dc outputs

can provide up to 0.5 amp each. Diagnostic features are short circuit,

open wire, and no load detection reported to the connector level on

inputs and point level on outputs. Local logic control has been

included. An external lug exists to ground the block.

43881

Ground lug

ArmorBlock MaXum 8 Input / 8 Output Module With Ground Lug

Publication 1792D-IN055A-EN-P - October 2004

Package Contents

Your package contains:

1 ArmorBlock MaXum module

these installation instructions

(Note: Cable bases are ordered and shipped separately.)

ATTENTION Environment and Enclosure

This equipment is intended for use in a Pollution Degree 2 industrial

environment, in overvoltage Category II applications (as defined in IEC

publication 60664-1), at altitudes up to 2000 meters without derating.

This equipment is considered Group 1, Class A industrial equipment according

to IEC/CISPR Publication 11. Without appropriate precautions, there may be

potential difficulties ensuring electromagnetic compatibility in other

environments due to conducted as well as radiated disturbance.

This equipment is supplied as "open type" equipment. It must be mounted

within an enclosure that is suitably designed for those specific environmental

conditions that will be present and appropriately designed to prevent

personal injury resulting from accessibility to live parts. The interior of the

enclosure must be accessible only by the use of a tool. Subsequent sections

of this publication may contain additional information regarding specific

enclosure type ratings that are required to comply with certain product safety

certifications.

NOTE: See NEMA Standards publication 250 and IEC publication 60529, as

applicable, for explanations of the degrees of protection provided by different

types of enclosure. Also, see the appropriate sections in this publication, as

well as the Allen-Bradley publication 1770-4.1 ("Industrial Automation Wiring

and Grounding Guidelines"), for additional installation requirements

pertaining to this equipment.

ArmorBlock MaXum 8 Input / 8 Output Module With Ground Lug

Publication 1792D-IN055A-EN-P - October 2004

To reset the node address, use a small blade screwdriver to rotate the

switches. Line up the small black dot on the switch with the number

setting you wish to use.

The rotary switches are read at module power up only. Settings from

64 through 99 cause the module to use the last valid node address

stored internally. For example, the last setting was 40. If a change is

made to 68, and then you power up, the address will default to 40.

Refer to the following illustration of the node address.

The module is equipped with AutoBaud detect. AutoBaud lets the

module read the settings already in use on your DeviceNet network

and automatically adjusts to follow those settings.

Install the Module

This module mounts to the following cable bases:

1792D-CBFM for KwikLink™ flat media installation

1792D-CB12 for 12mm drop cable installation

1792D-CB18P for round media DeviceNet and output power

other optional cable base assembly.

IMPORTANT

The cable base should already be installed. For

more information about the cable base, see

publication 1792D-IN036 (CB18P) or 1792D-IN009

(CBFM, CB12).

NODE ADDRESS

(00-63 PGM)

LSDMSD

012

Bottom View of Module

41462

Node Address

is set at 62;

see small

black dots.

ArmorBlock MaXum 8 Input / 8 Output Module With Ground Lug

Publication 1792D-IN055A-EN-P - October 2004

To install the module:

Position the module over the mounted cable base. Align the

three captive screws in the module with the accepting

receptacles in the base.

Tighten the screws with a torque of 8 inch-pounds to secure

the module to the base.

Note: Dimensions change according to the cable base and

module combination used.

IMPORTANT

Proper alignment of the screws is necessary to

complete the connections between the module

contacts and the cable contacts.

WARNING

When used in a Class I, Division 2, hazardous

location, this equipment must be mounted in a

suitable enclosure with proper wiring method that

complies with the governing electrical codes.

Align the

screws to

properly

secure the

module to

the base.

Cable Base 1792D-CBFM

is used for this example.

.9in. (48.26mm)

2.7in.(68.6mm)

6.85in. (174mm)

43875

Ground lug

ArmorBlock MaXum 8 Input / 8 Output Module With Ground Lug

Publication 1792D-IN055A-EN-P - October 2004

Connect the Input / Output Cord Sets to the MaXum Module

This module uses 5 pin micro (12mm) style PCB mounted connectors.

Eight micro caps cover the connectors on your module. Remove the

caps and connect your cord sets to the appropriate ports. This

product has two inputs or outputs per I/O connector. Use a “Y”

splitter cable

for access to all I/O connections.

Use the micro caps to cover and seal unused ports. The following

illustration shows pinout diagrams for the connectors.

WARNING

If you connect or disconnect the communications cable

with power applied to this module or any device on the

network, an electrical arc can occur. This could cause an

explosion in hazardous location installations.

Input Micro-Connector

(view into socket)

Pin 1 Sensor Source voltage

Pin 2 Input B

Pin 3 Return Logic Ground1

Pin 4 Input A

Pin 5 PE

Output Micro-Connector

(view into socket)

Pin 1 Not Used

Pin 2 Output B

Pin 3 Auxiliary Power Ground

Pin 4 Output A

Pin 5 PE 41452

1Logic Ground is approximately 0.4V above DeviceNet V- measured at the module.

ArmorBlock MaXum 8 Input / 8 Output Module With Ground Lug

Publication 1792D-IN055A-EN-P - October 2004

Refer to publication 889-5.0 for Rockwell Automation cables and cord

sets offerings.

WARNING

Use supply wires suitable for 30°C above

surrounding ambient.

IMPORTANT

If the devices (sensors) connected to the input

connections require Class 2 power to operate, the

DeviceNet connections of this equipment must be

ATTENTION

Make sure all connections and caps are securely

tightened to properly seal the connections against

leaks and maintain IP67 requirements.

For maximum noise immunity, input and output

cable return wires must be properly terminated.

When inputs and outputs are connected in

loopback, return wires should be connected

together.

I/O cable length should be less than 30 meters.

ArmorBlock MaXum 8 Input / 8 Output Module With Ground Lug

Publication 1792D-IN055A-EN-P - October 2004

I/O connectors for this module are shown below.

Output Power and DeviceNet Cables

Output power and DeviceNet cables are described in the installation

publications for the cable base assembly of your choice. Refer to the

following publications:

1792D-IN009 ArmorBlock MaXum Cable Base Installation

Instructions

DN-6.7.2 DeviceNet Cable Planning and Installation Manual

WARNING

If you connect or disconnect wiring while the

field-side power is on, an electrical arc can occur.

This could cause an explosion in hazardous

location installations. Be sure that power is

removed or the area is nonhazardous before

proceeding.

I-4

I-5

I-6

I-7

O-4

O-5

I-2

I-3

O-2

O-3

O-6

O-7

Logic Status Net/Mod Status

I-0

I-1

O-0

O-1

Auxilary Power

41517

Input 0

Input 1

Input 2

Input 3

Input 4

Input 5

Input 6

Input 7

Output 0

Output 1

Output 2

Output 3

Output 4

Output 5

Output 6

Output 7

Connector A

onnector B

onnector C

Connector D

Connector E

Connector F

Connector G

Connector H

ArmorBlock MaXum 8 Input / 8 Output Module With Ground Lug

Publication 1792D-IN055A-EN-P - October 2004

The following table describes individual I/O status indicators.

Specifications

I/O Status Indicators

Function Module Status Indicator Point

Indicator1Status

Outputs Green

Green

Module Status blink red

None

Yellow

Orange

Red

Orange

Red

Output not energized

Output energized

Output shorted - auto restart

Output shorted - latching

Output no load - auto restart

Output no load - latching

Inputs Green

Green

Module Status blink red

None

Yellow

Red

Blink red

No valid input

Valid input

Short on input connector1

Off wire on input connector

1Only the first LED of each input connector will light as red when twin inputs are used.

8 Input / 8 Output Module - Cat. No. 1792D-8BVT8PE

Input Specifications Maximum Minimum

Inputs per block 8 - 3 wire or dry contact PNP devices or 4 - 4 wire PNP devices

Sensor Source Current (per connector) 100mA total -

Off-wire Sense Current 0.5mA -

On-state Voltage 25V dc 10V dc

On-state Current 10mA 2mA

Off-state Voltage 5V dc -

Off-state Current - 1.5mA

Output Specifications Maximum Minimum

Outputs per block 8 sourcing outputs labeled O0 through O7

Off Peak Blocking Voltage 30V 10V

On-state Voltage Drop 1V -

On-state Current 0.5A -

Off-state Leakage 1.5mA -

Module Current (all outputs) 4.0A -

Surge Current - for 10ms, repeatable

every 2s 2.4A -

No Load Sense Current (On-state) 0.18A -

ArmorBlock MaXum 8 Input / 8 Output Module With Ground Lug

Publication 1792D-IN055A-EN-P - October 2004

General Specifications Maximum Minimum

DeviceNet Power Voltage

Current 25V dc max

150mA max (no sensors) 11V dc min

up to 1.4A (8 sensors @

50mA per sensor)

Auxiliary Power Voltage

Current 30V dc max

4A max 10V dc min

4A max

Indicators Net/Mod Status - red/green

Logic Status - green

Auxiliary Power - green

Point LED - yellow/orange/red

Communication Rate

125Kbps @ 500 meters(1600 feet) for thick cable, flat

media length 375 meters (1230 feet)

250Kbps @ 200 meters(600 feet) for thick cable, flat

media length 150 meters (492 feet)

500Kbps @ 100 meters (330 feet) for thick cable, flat

media length 75 meters (246 feet)

Dimensions (assembled to base)

inches - (Millimeters) 1.9H x 2.7W x 6.9D

(48)H x (69)W x (174)D

Operational Temperature IEC 60068-2-1 (Test Ad, Operating Cold),

IEC 60068-2-2 (Test Bd, Operating Dry Heat),

IEC 60068-2-14 (Test Nb, Operating Thermal Shock):

-25 to 60°(-13 to 140°F)

Storage Temperature IEC 60068-2-1 (Test Ab, Un-packaged Non-operating Cold),

IEC 60068-2-2 (Test Bb, Un-packaged Non-operating Dry Heat),

IEC 60068-2-14 (Test Na, Un-packaged Non-operating Thermal

Shock):

-25 to 80°(-13 to 176°F)

Relative Humidity IEC 60068-2-30 (Test Db, Un-packaged Non-operating Damp

Heat):

5 to 95% non-condensing

Vibration IEC 60068-2-6 (Test Fc, Operating):

10g @ 10-500 Hz

8 Input / 8 Output Module - Cat. No. 1792D-8BVT8PE

ArmorBlock MaXum 8 Input / 8 Output Module With Ground Lug

Publication 1792D-IN055A-EN-P - October 2004

General Specifications (continued)

Operating Shock IEC 60068-2-27 (Test Ea, Unpackaged Shock):

30g

Non-Operating Shock IEC 60068-2-27 (Test Ea, Unpackaged Shock):

50g

Emissions CISPR 11:

Group 1, Class A

ESD Immunity IEC 61000-4-2:

6kV contact discharges

8kV air discharges

Radiated RF Immunity IEC 61000-4-3:

10V/m with 1kHz sine-wave 80%AM from 30MHz to 2000MHz

10V/m with 200Hz 50% Pulse 100%AM at 900MHz|

10V/m with 200Hz 50% Pulse 100%AM at 1890MHz

EFT/B Immunity IEC 61000-4-4:

±2kV at 5kHz on power ports

±2kV at 5kHz on signal ports

±2kV at 5kHz on communications ports

Surge Transient Immunity IEC 61000-4-5:

±1kV line-line(DM) and ±2 line-earth(CM) on power ports

±1kV line-line(DM) and ±2kV line-earth(CM) on signal ports

±2kV line-earth(CM) on communications ports

Conducted RF Immunity IEC 61000-4-6:

10Vrms with 1kHz sine-wave 80%AM from 150kHz to 80MHz

Conductors Publication DN-6.7.2

Enclosure Meets IP67

Supply Voltages/Voltage Ranges DNet Power: 11V dc to 25V dc;

Auxiliary Power: 10V dc to 30V dc

Supply Power/Current Ratings DNet current:1.6A;

Input current: 50mA;

Output power: 60VA DC-13/SQ;

Outputs 4A total;

Auxiliary current:4A

Isolation voltage (continuous-voltage

withstand rating) Tested to withstand 750V dc for 60 seconds

Wire Size Use 14-22 AWG wire with insulation temperature rating of

75°C min.See Publication DN-6.7.2; Category: 2.

Wiring Category12 - on signal ports

2 - on power ports

2 - on communications ports

8 Input / 8 Output Module - Cat. No. 1792D-8BVT8PE

Inhaltsverzeichnis

Andere Rockwell Automation Steuereinheit Handbücher

Rockwell Automation

Rockwell Automation FlexPak 3000 OIM Bedienungsanleitung

Rockwell Automation

Rockwell Automation Bulletin 193 E1 PLUS Benutzerhandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix DeviceNet... Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-BOOLEAN Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley DM2 Benutzerhandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley FLEX Ex 1797-IRT8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen Bradley Guardmaster Sipha 2 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 750 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 800G-XBx-EX Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 750 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Compact GuardLogix 5370... Benutzerhandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley IntelliVAC Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 193-EGJ Series Benutzerhandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley 794-IRT8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted T8834 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-IB16ISOE Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-MVI Bedienungsanleitung

Rockwell Automation

Rockwell Automation ArmorBlock Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1746-BTM Bedienungsanleitung

Rockwell Automation

Rockwell Automation MAO04NND Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1794-OB8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLSBATASSY3 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley SLC 500 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-HSC Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung