Rockwell Automation 1766-L32AWA Bedienungsanleitung

Installation Instructions

MicroLogix 1400 Programmable Controllers

Catalog Number(s) 1766-L32AWA, 1766-L32AWAA,

1766-L32BWA, 1766-L32BWAA, 1766-L32BXB,

1766-L32BXBA

Topic Page

Important User Information 2

Additional Resources 5

Overview 6

Controller Description 7

Hazardous Location Considerations 9

Mount the Controller 11

Connect 1762 I/O Expansion Modules 16

Wire the Controller 17

Specifications 26

2MicroLogix 1400 Programmable Controllers

Publication 1766-IN001D-EN-P - June 2015

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical equipment.

Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication

SGI-1.1 available from your local Rockwell Automation sales office or online at

http://literature.rockwellautomation.com) describes some important differences between solid state

equipment and hard-wired electromechanical devices. Because of this difference, and also because of the

wide variety of uses for solid state equipment, all persons responsible for applying this equipment must

satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many

variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot

assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING

Identifies information about practices or circumstances that can cause an explosion in

a hazardous environment, which may lead to personal injury or death, property

damage, or economic loss.

IMPORTANT

Identifies information that is critical for successful application and understanding of

the product.

ATTENTION

Identifies information about practices or circumstances that can lead to personal injury

or death, property damage, or economic loss. Attentions help you identify a hazard,

avoid a hazard and recognize the consequences.

SHOCK HAZARD

Labels may be on or inside the equipment (for example, drive or motor) to alert people

that dangerous voltage may be present.

BURN HAZARD

Labels may be on or inside the equipment (for example, drive or motor) to alert people

that surfaces may reach dangerous temperatures.

MicroLogix 1400 Programmable Controllers 3

Publication 1766-IN001D-EN-P - June 2015

Environment and Enclosure

Preventing Electrostatic Discharge

ATTENTION

This equipment is intended for use in a Pollution Degree 2 industrial

environment, in overvoltage Category II applications (as defined in IEC

publication 60664-1), at altitudes up to 2000 meters (6562 ft) without derating.

This equipment is considered Group 1, Class A industrial equipment according to

IEC/CISPR Publication 11. Without appropriate precautions, there may be

potential difficulties ensuring electromagnetic compatibility in other

environments due to conducted as well as radiated disturbance.

This equipment is supplied as open-type equipment. It must be mounted within

an enclosure that is suitably designed for those specific environmental

conditions that will be present and appropriately designed to prevent personal

injury resulting from accessibility to live parts. The enclosure must have suitable

flame-retardant properties to prevent or minimize the spread of flame,

complying with a flame spread rating of 5VA, V2, V1, V0 (or equivalent) if

non-metallic. The interior of the enclosure must be accessible only by the use of

a tool. Subsequent sections of this publication may contain additional

information regarding specific enclosure type ratings that are required to comply

with certain product safety certifications.

ATTENTION

This equipment is sensitive to electrostatic discharge, which can cause internal

damage and affect normal operation. Follow these guidelines when you handle

this equipment:

•Touch a grounded object to discharge potential static.

•Wear an approved grounding wriststrap.

•Do not touch connectors or pins on component boards.

•Do not touch circuit components inside the equipment.

•Use a static-safe workstation, if available.

•Store the equipment in appropriate static-safe packaging when not in use.

4MicroLogix 1400 Programmable Controllers

Publication 1766-IN001D-EN-P - June 2015

North American Hazardous Location Approval

The following modules are North American Hazardous Location approved: 1766-L32AWA,

1766-L32AWAA, 1766-L32BWA, 1766-L32BWAA, 1766-L32BXB, 1766-L32BXBA

The following information applies when

operating this equipment in hazardous

locations:

Informations sur l’utilisation de cet

équipement en environnements

dangereux:

Products marked "CL I, DIV 2, GP A, B, C, D" are

suitable for use in Class I Division 2 Groups A, B, C,

D, Hazardous Locations and nonhazardous locations

only. Each product is supplied with markings on the

rating nameplate indicating the hazardous location

temperature code. When combining products within

a system, the most adverse temperature code

(lowest "T" number) may be used to help determine

the overall temperature code of the system.

Combinations of equipment in your system are

subject to investigation by the local Authority Having

Jurisdiction at the time of installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne

conviennent qu’à une utilisation en environnements

de Classe I Division 2 Groupes A, B, C, D dangereux et

non dangereux. Chaque produit est livré avec des

marquages sur sa plaque d’identification qui

indiquent le code de température pour les

environnements dangereux. Lorsque plusieurs

produits sont combinés dans un système, le code de

température le plus défavorable (code de température

le plus faible) peut être utilisé pour déterminer le code

de température global du système. Les combinaisons

d’équipements dans le système sont sujettes à

inspection par les autorités locales qualifiées au

moment de l’installation.

WARNING

EXPLOSION HAZARD

•Do not disconnect while the

circuit is live or unless the area

is known to be free of ignitible

concentrations.

•Do not disconnect connections

to this equipment unless power

has been removed or the area is

known to be nonhazardous.

Secure any external connections

that mate to this equipment by

using screws, sliding latches,

threaded connectors, or other

means provided with this

product.

•Substitution of components may

impair suitability for Class I,

Division 2.

•Do not remove or replace lamps,

fuses or plug-in modules (as

applicable) unless power has

been disconnected or the area is

known to be free of ignitible

concentrations of flammable

gases or vapors.

AVERTISSEMENT

RISQUE D’EXPLOSION

•Couper le courant ou s’assurer

que l’environnement est classé

non dangereux avant de

débrancher l'équipement.

•Couper le courant ou s'assurer

que l’environnement est classé

non dangereux avant de

débrancher les connecteurs. Fixer

tous les connecteurs externes

reliés à cet équipement à l'aide

de vis, loquets coulissants,

connecteurs filetés ou autres

moyens fournis avec ce produit.

•La substitution de composants

peut rendre cet équipement

inadapté à une utilisation en

environnement de Classe I,

Division 2.

•S’assurer que l’environnement

est classé non dangereux avant

de changer les piles.

MicroLogix 1400 Programmable Controllers 5

Publication 1766-IN001D-EN-P - June 2015

Additional Resources

If you would like a manual, you can:

•download a free electronic version from the internet:

http://literature.rockwellautomation.com

•purchase a printed manual by contacting your local Allen-Bradley distributor or

Rockwell Automation representative

Resource Description

MicroLogix 1400 Programmable Controllers User

Manual 1766-UM001

A more detailed description of how to install and use

your MicroLogix 1400 programmable controller and

expansion I/O system.

MicroLogix 1400 Instruction Set Reference

Manual 1766-RM001

A reference manual that contains data and function

files, instruction set, and troubleshooting information

for MicroLogix 1400.

Installation Instructions 1762-INxxx Information on installing and using 1762 expansion I/O

modules.

Industrial Automation Wiring and Grounding

Guidelines 1770-4.1

More information on proper wiring and grounding

techniques.

6MicroLogix 1400 Programmable Controllers

Publication 1766-IN001D-EN-P - June 2015

Overview

MicroLogix 1400 controllers are suitable for use in an industrial environment when installed

in accordance with these instructions. Specifically, this equipment is intended for use in clean,

dry environments (Pollution degree 2(1)) and with circuits not exceeding Over Voltage

Category II(2) (IEC 60664-1)(3). AC powered products must be connected to the secondary of

an isolating transformer.

Install your controller using these installation instructions.

(1) Pollution Degree 2 is an environment where, normally, only non-conductive pollution occurs except that occasionally a

temporary conductivity caused by condensation shall be expected.

(2) Over Voltage Category II is the load level section of the electrical distribution system. At this level transient voltages are

controlled and do not exceed the impulse voltage capability of the product's insulation.

(3) Pollution Degree 2 and Over Voltage Category II are International Electrotechnical commissions (IEC) designations.

ATTENTION

Do not remove the protective debris strip until after the controller and all other

equipment in the panel near the controller are mounted and wiring is complete.

Once wiring is complete, remove protective debris strip. Failure to remove strip

before operating can cause overheating.

ATTENTION

Electrostatic discharge can damage semiconductor devices inside the controller.

Do not touch the connector pins or other sensitive areas.

Debris strip

44513

MicroLogix 1400 Programmable Controllers 7

Publication 1766-IN001D-EN-P - June 2015

Controller Description

Description

1 Comm port 2 - 9-pin D-Shell RS-232C connector

2 Memory module (refer to MicroLogix 1400 Memory Module Installation Instructions, publication

1766-IN010 for instructions on installing the memory module).

3 User 24V (for 1766-L32BWA and 1766-L32BWAA only)

4 Input terminal block

5 LCD Display Keypad (ESC, OK, Up, Down, Left, Right)

6 Battery compartment

7 1762 expansion bus connector

8 Battery connector

9 Output terminal block

10 LCD Display

11 Indicator LED panel

12 Comm port 1 - RJ45 connector

13 Comm port 0 - 8-pin mini DIN RS-232C/RS-485 connector

ESC

256 7

9101113 12

44515

44514

Left side view Top view

8MicroLogix 1400 Programmable Controllers

Publication 1766-IN001D-EN-P - June 2015

Controller Input and Output Description

Catalog

Number

Description

Input

Power

User

Power

Embedded

Discrete I/O

Embedded

Analog I/O

Comm.

Ports

1766-L32BWA

100/240V AC

24V DC

12 Fast 24V DC Inputs

8 Normal 24V DC Inputs

12 Relay Outputs

None

1RS232/RS485(1)

1 Ethernet/IP

1 RS232(2)

1766-L32AWA

None

20 120V AC Inputs

12 Relay Outputs

1766-L32BXB 24 V DC

12 Fast 24V DC Inputs

8 Normal 24V DC Inputs

6 Relay Outputs

3 Fast DC Outputs

3 Normal DC Outputs

1766-L32BWAA

100/240V AC

24V DC

12 Fast 24V DC Inputs

8 Normal 24V DC Inputs

12 Relay Outputs

4 Voltage Inputs

2 Voltage

Outputs

1766-L32AWAA

None

20 120V AC Inputs

12 Relay Outputs

1766-L32BXBA 24V DC

12 Fast 24V DC Inputs

8 Normal 24V DC Inputs

6 Relay Outputs

3 Fast DC Outputs

3 Normal DC Outputs

(1) Isolated RS-232/RS-485 combo port. Same as ML1100 Comm 0

(2) Non-isolated RS-232. Standard D-sub connector

MicroLogix 1400 Programmable Controllers 9

Publication 1766-IN001D-EN-P - June 2015

Hazardous Location Considerations

This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D or non-hazardous

locations only. The following WARNING statement applies to use in hazardous locations.

Use only the following communication cables in Class I, Division 2 hazardous locations.

WARNING

EXPLOSION HAZARD

•Substitution of components may impair suitability for Class I, Division 2.

•Do not replace components or disconnect equipment unless power has been switched

off.

•Do not connect or disconnect components unless power has been switched off.

•This product must be installed in an enclosure. All cables connected to the product

must remain in the enclosure or be protected by conduit or other means.

•All wiring must comply with N.E.C. article 501-10(b) and/or in accordance with

Section 18-1J2 of the Canadian Electrical Code, and in accordance with the authority

having jurisdiction.

•For applicable equipment (for example, relay modules), exposure to some chemicals

may degrade the sealing properties of the materials used in these devices:

–Relays, epoxy

It is recommended that you periodically inspect these devices for any degradation of

properties and replace the module if degradation is found.

Environment Classification Communication Cables

Class I, Division 2 Hazardous Environment 1761-CBL-AC00 Series C or later

1761-CBL-AM00 Series C or later

1761-CBL-AP00 Series C or later

1761-CBL-PM02 Series C or later

1761-CBL-HM02 Series C or later

2707-NC9 Series C or later

1763-NC01 Series A or later

1747-CP3 Series

10 MicroLogix 1400 Programmable Controllers

Publication 1766-IN001D-EN-P - June 2015

Environnements dangereux

Cet équipement est conçu pour une utilisation en environnements dangereux de Classe I,

Division 2, Groupes A, B, C, D ou non dangereux. La mise en garde suivante s’applique à

utilisation en environnements dangereux.

Utilisez uniquement les câbles de communication suivants dans les environnements

dangereux de Classe I, Division 2.

WARNING

DANGER D’EXPLOSION

•La substitution de composants peut rendre cet équipement impropre à une utilisation

en environnement de Classe I, Division 2.

•Ne pas remplacer de composants ou déconnecter l’équipement sans s’être assuré que

l’alimentation est coupée.

•Ne pas connecter ou déconnecter des composants sans s’être assuré que

l’alimentation est coupée.

•Ce produit doit être installé dans une armoire. Tous les câbles connectés à l’appareil

doivent rester dans l’armoire ou être protégés par une goulotte ou tout autre moyen.

•L’ensemble du câblage doit être conforme à la réglementation en vigueur dans les

pays où l’appareil est installé.

Classification des environnements Câbles de communication

Environnement dangereux de Classe I, Division 2 1761-CBL-AC00 série C ou ultérieure

1761-CBL-AM00 série C ou ultérieure

1761-CBL-AP00 série C ou ultérieure

1761-CBL-PM02 série C ou ultérieure

1761-CBL-HM02 série C ou ultérieure

2707-NC9 série C ou ultérieure

1763-NC01 série A ou ultérieure

série 1747-CP3

ATTENTION

UNSUPPORTED CONNECTION

Do not connect the Comm0 port on the MicroLogix 1400 controller to another MicroLogix

family controller such as MicroLogix 1000, MicroLogix 1200, or MicroLogix 1500 using a

1761-CBL-AM00 (8-pin mini-DIN to 8-pin mini-DIN) cable or equivalent.

This type of connection will cause damage to the RS-232/485 communication port

(Channel 0) of the MicroLogix 1400 and/or the controller itself. Communication pins used

for RS-485 communications are alternately used for 24V power on the other MicroLogix

controllers.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockwell Automation Controller Handbücher

Rockwell Automation

Rockwell Automation Allen-Bradley 1769 CompactLogix Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L23E-QB1B Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley DriveLogix 5730 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley MicroLogix 1400 Bedienungsanleitung

Rockwell Automation

Rockwell Automation SmartGuard 600 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1336 PLUS Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Logix 5000 Series Betriebsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 856T-B24LC Bedienungsanleitung

Rockwell Automation

Rockwell Automation MPMA Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley CompactLogix 5370 Bedienungsanleitung

Rockwell Automation

Rockwell Automation SLC 500 Thermocouple Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley MicroLogix 1400 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Micro800 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley GuardLogix Benutzerhandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley Logix 5000 Series Betriebsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 40 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley AADvance T9110 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Micro830 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1756-L1 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley CompactLogix 5370 L2 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Samsung NX70 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley LiquiFlo 2.0 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 7000 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung