Rockwell Automation 1769-L23E-QB1B Bedienungsanleitung

Installation Instructions

CompactLogix Packaged Controllers

Catalog Numbers 1769-L23E-QB1B, 1769-L23E-QBFC1B, 1769-L23-QBFC1B

Topic Page

Important User Information 2

Before You Begin 4

Restrictions 4

Parts 5

Required System Components 6

Installation Checklist 7

Packaged Controller Dimensions 8

Install the Battery 10

Connect Expansion Modules (optional) 11

Panel Mount the System 13

DIN-rail Mount the System 13

Wiring Power to the System 15

Wire the I/O Removable Terminal Blocks 16

Expansion Module Wiring 27

Connect Using the RS-232 Connection 27

Connect Using the Ethernet Connection 28

Download and Install EDS Files 29

Download Packaged Controller Firmware 29

Use the AutoFlash Feature of RSLogix 5000 to Load Firmware 29

Use the ControlFlash Utility to Load Firmware 33

Select the Packaged Controller’s Operating Mode 36

Status Indicators 37

Specifications 45

Additional Resources 59

2CompactLogix Packaged Controllers

Publication 1769-IN082A-EN-P - July 2008

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical equipment.

Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication

SGI-1.1 available from your local Rockwell Automation sales office or online at

http://literature.rockwellautomation.com) describes some important differences between solid state

equipment and hard-wired electromechanical devices. Because of this difference, and also because of the

wide variety of uses for solid state equipment, all persons responsible for applying this equipment must

satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many

variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot

assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING Identifies information about practices or circumstances that can cause an explosion in

a hazardous environment, which may lead to personal injury or death, property

damage, or economic loss.

IMPORTANT Identifies information that is critical for successful application and understanding of

the product.

ATTENTION Identifies information about practices or circumstances that can lead to personal injury

or death, property damage, or economic loss. Attentions help you identify a hazard,

avoid a hazard and recognize the consequences.

SHOCK HAZARD

Labels may be on or inside the equipment, for example, a drive or motor, to alert

people that dangerous voltage may be present.

BURN HAZARD

Labels may be on or inside the equipment, for example, a drive or motor, to alert

people that surfaces may reach dangerous temperatures.

CompactLogix Packaged Controllers 3

Publication 1769-IN082A-EN-P - July 2008

North American Hazardous Location Approval

Environment and Enclosure

The following information applies when operating

this equipment in hazardous locations. Informations sur l’utilisation de cet équipement en

environnements dangereux.

Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for use in

Class I Division 2 Groups A, B, C, D, Hazardous Locations and

nonhazardous locations only. Each product is supplied with

markings on the rating nameplate indicating the hazardous

location temperature code. When combining products within a

system, the most adverse temperature code (lowest "T" number)

may be used to help determine the overall temperature code of

the system. Combinations of equipment in your system are subject

to investigation by the local Authority Having Jurisdiction at the

time of installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne conviennent

qu'à une utilisation en environnements de Classe I Division 2

Groupes A, B, C, D dangereux et non dangereux. Chaque produit

est livré avec des marquages sur sa plaque d'identification qui

indiquent le code de température pour les environnements

dangereux. Lorsque plusieurs produits sont combinés dans un

système, le code de température le plus défavorable (code de

température le plus faible) peut être utilisé pour déterminer le

code de température global du système. Les combinaisons

d'équipements dans le système sont sujettes à inspection par les

autorités locales qualifiées au moment de l'installation.

WARNING EXPLOSION HAZARD -

• Do not disconnect equipment

unless power has been removed

or the area is known to be

nonhazardous.

• Do not disconnect connections to

this equipment unless power has

been removed or the area is

known to be nonhazardous.

Secure any external connections

that mate to this equipment by

using screws, sliding latches,

threaded connectors, or other

means provided with this product.

• Substitution of components may

impair suitability for Class I,

Division 2.

• If this product contains batteries,

they must only be changed in an

area known to be nonhazardous.

AVERTISSEMENT RISQUE D’EXPLOSION –

• Couper le courant ou s'assurer

que l'environnement est classé

non dangereux avant de

débrancher l'équipement.

• Couper le courant ou s'assurer

que l'environnement est classé

non dangereux avant de

débrancher les connecteurs. Fixer

tous les connecteurs externes

reliés à cet équipement à l'aide

de vis, loquets coulissants,

connecteurs filetés ou autres

moyens fournis avec ce produit.

• La substitution de composants

peut rendre cet équipement

inadapté à une utilisation en

environnement de Classe I,

Division 2.

• S'assurer que l'environnement est

classé non dangereux avant de

changer les piles.

ATTENTION This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage

Category II applications (as defined in IEC publication 60664-1), at altitudes up to 2000 m (6562 ft)

without derating.

This equipment is considered Group 1, Class A industrial equipment according to IEC/CISPR Publication

11. Without appropriate precautions, there may be potential difficulties ensuring electromagnetic

compatibility in other environments due to conducted as well as radiated disturbance.

This equipment is supplied as open-type equipment. It must be mounted within an enclosure that is

suitably designed for those specific environmental conditions that will be present and appropriately

designed to prevent personal injury resulting from accessibility to live parts. The enclosure must have

suitable flame-retardant properties to prevent orminimize the spread of flame, complying with a flame

spread rating of 5VA, V2, V1, V0 (or equivalent) if non-metallic. The interior of the enclosure must be

accessible only by the use of a tool. Subsequent sections of this publication may contain additional

information regarding specific enclosure type ratings that are required to comply with certain product

safety certifications.

In addition to this publication, see:

•Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1, for additional

installation requirements.

•NEMA Standards publication 250 and IEC publication 60529, as applicable, for explanations of the

degrees of protection provided by different types of enclosure.

4CompactLogix Packaged Controllers

Publication 1769-IN082A-EN-P - July 2008

Prevent Electrostatic Discharge

Before You Begin

This section contains information you should understand before installing the

CompactLogix packaged controller.

Restrictions

The maximum amount of expansion modules that can be used with the packaged

controllers is two. Within that limit, the number of expansion I/O modules that can

be attached to the packaged controller depends on the bus current draw of the

modules being attached.

Each packaged controller has a specified amount of available bus current as shown

in this table.

To determine the number of expansion I/O modules you can add, total the bus

current draw (maximum) of your planned expansion I/O modules and the end cap.

If your result is less than the packaged controller’s maximum available bus current,

you are within the expansion I/O limit of your packaged controller.

ATTENTION This equipment is sensitive to electrostatic discharge, which can cause internal damage

and affect normal operation. Follow these guidelines when you handle this equipment:

•Touch a grounded object to discharge potential static.

•Wear an approved grounding wriststrap.

•Do not touch connectors or pins on component boards.

•Do not touch circuit components inside the equipment.

•Use a static-safe workstation, if available.

•Store the equipment in appropriate static-safe packaging when not in use.

Packaged Controller Bus Current and Expansion Module Limits

Cat. No. Total Available 5V DC Bus Current

1769-L23E-QB1B 1 A (1000 mA)

1769-L23E-QBFC1B 450 mA

1769-L23-QBFC1B 800 mA

CompactLogix Packaged Controllers 5

Publication 1769-IN082A-EN-P - July 2008

Example of Expansion I/O Calculation:

In this example, these expansion I/O modules and bus current draws are planned

for use with the 1769-L23E-QBFC1B packaged controller.

The total bus current draw of the Compact I/O modules (310 mA) is less than the

total available bus current of the packaged controller (450 mA). These planned

expansion I/O modules are within the limits of the 1769-L23E-QBFC1B packaged

controller.

Parts (included with the packaged controller)

These components are included with your CompactLogix packaged controller.

Parts (optional, not included with the packaged controller)

In addition to the parts included with the packaged controller, you may choose to

use these components specific to your application.

Planned Expansion I/O Module Bus Current Draw, max(1)

(1) The maximum bus current draw specification for each Compact I/O module is available in the Compact I/O Selection Guide,

publication 1769-SG002. This publication also provides further explanation of and a table for the calculation of Compact I/O

power supply requirements.

1769-OV16 Sink Output Module 200 mA

1769-IF4 Analog Input Module 105 mA

1769-ECR End Cap 5 mA

Total Bus Current Draw: 310 mA

Cat. No. Part

1747-KY Key

1769-BA Battery

1769-ECR End cap

If using Then use this component

RS-232 port to connect to the packaged

controller.

1756-CP3 or 1747-CP3 serial cable.

EtherNet/IP port to connect to the packaged

controller.

Standard Ethernet cable with an RJ45 connector, or, for

industrial grade requirements, 1585J Ethernet

connectivity media.

Panel mount method to install the packaged

controller.

4…8 M4 or #8 panhead screws (depending on the number

of expansion modules used).

6CompactLogix Packaged Controllers

Publication 1769-IN082A-EN-P - July 2008

Replacement Parts

These CompactLogix packaged controller replacement parts are available for order.

Required Tools

The only tool required for the installation of the CompactLogix packaged controller

is a medium-sized Phillips-head screwdriver.

Required System Components

Use these system components with your CompactLogix packaged controller.

Catalog No. Description Compatible Packaged Controllers

1769-BA CompactLogix packaged controller

battery

1769-L23E-QB1B, 1769-L23E-QBFC1B, and

1769-L23-QBFC1B

1769-ECR Compact right end cap 1769-L23E-QB1B, 1769-L23E-QBFC1B, and

1769-L23-QBFC1B

1769-RDQB CompactLogix packaged controller door 1769-L23E-QB1B

1769-RDQBFC CompactLogix packaged controller door 1769-L23E-QBFC1B and 1769-L23-QBFC1B

Software Component Version

RSLogix 5000 17.00 or later

RSLinx Classic 2.52(1)

(1) You may use an earlier version of RSLinx software, however, if you do so,

you must download and install the EDS files specific to these controllers.

Also, if you are using Windows Vista, you must use RSLinx Classic

software, version 2.54.

CompactLogix Packaged Controllers 7

Publication 1769-IN082A-EN-P - July 2008

Installation Checklist

This table lists tasks that must be completed to fully install and begin using your

packaged controller.

9Installation Tasks

Install the Battery

Connect Expansion Modules (optional)

Panel Mount the System or DIN-rail Mount the System

Minimum Spacing Requirements

Grounding Considerations

Wire the I/O Removable Terminal Blocks

Connect Using the RS-232 Connection

Download and Install EDS Files

Download and Install Controller Firmware

Use the AutoFlash Feature of RSLogix 5000 to Load Firmware

or Use the ControlFlash Utility to Load Firmware

8CompactLogix Packaged Controllers

Publication 1769-IN082A-EN-P - July 2008

Packaged Controller Dimensions

1769-L23E-QB1B Packaged Controller

The 1769-L23E-QB1B controller has these approximate dimensions.

Measurement Dimension, approx.

a185.2 mm (7.29 in)

b123.86 mm (4.88 in)

c118 mm (4.65 in)

d132 mm (5.20in)

e132.9 mm (5.23 in)

f18 mm (.71 in)

CompactLogix L23E

bcd

CompactLogix Packaged Controllers 9

Publication 1769-IN082A-EN-P - July 2008

1769-L23E-QBFC1B and 1769-L23-QBFC1B Packaged Controllers

The 1769-L23E-QBFC1B and 1769-L23-QBFC1B packaged controllers have these

approximate dimensions.

Measurement(1)

(1) Applies to both the 1769-L23E-QBFC1B and

1769-L23-QBFC1B packaged controllers.

Dimension, approx.

a249.25 mm (9.81 in)

b123.86 mm (4.88 in)

c118 mm (4.65 in)

d132 mm (5.20in)

e98.475 mm (3.88 in)

f98.475 mm (3.88 in)

g18 mm (.71 in)

CompactLogix L23E

CompactLogix L23

BATT

I/O

DCH 0

FORCE

RUN

10 CompactLogix Packaged Controllers

Publication 1769-IN082A-EN-P - July 2008

Install the Battery

Complete these steps to install the battery on your packaged controller.

1. Open the battery door on the left side of the packaged controller.

2. Carefully attach the battery connector to the port located inside the

packaged controller.

3. Insert the battery, wires down, in the slot on the battery door.

4. Close the battery door.

WARNING When you connect or disconnect the battery an electrical arc can occur. This could cause

an explosion in hazardous location installations. Be sure that the area is nonhazardous

before proceeding.

For Safety information on the handling of lithium batteries, including handling and

disposal of leaking batteries, see Guidelines for Handling Lithium Batteries, publication

AG 5-4.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockwell Automation Controller Handbücher

Rockwell Automation

Rockwell Automation Reliance SP500 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1756-L1 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Guardmaster 440G-MZ Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley DriveLogix 5730 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Logix 5000 Series Betriebsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 23PFC Betriebsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley CompactLogix 5370 L2 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Micro800 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Micro830 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley MicroLogix 1400 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1502 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley MicroLogix 1400 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1785 PLC-5 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700 Bedienungsanleitung

Rockwell Automation

Rockwell Automation CompactLogix series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley CompactLogix 1769-L32E Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Logix 5000 Series Betriebsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Micro820 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 40 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley G Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch