Rockwell Automation PowerFlex 700S Bedienungsanleitung

INSTALLATION MANUAL

Frames 9 - 14

PowerFlex® 700H Adjustable Frequency AC Drive /

PowerFlex® 700S High Performance AC Drive

Important User Information Solid state equipment has operational characteristics differing from those of

electromechanical equipment. Safety Guidelines for the Application,

Installation and Maintenance of Solid State Controls (Publication SGI-1.1

available from your local Rockwell Automation sales office or online at http://

www.rockwellautomation.com/literature) describes some important differences

between solid state equipment and hard-wired electromechanical devices.

Because of this difference, and also because of the wide variety of uses for solid

state equipment, all persons responsible for applying this equipment must

satisfy themselves that each intended application of this equipment is

acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect

or consequential damages resulting from the use or application of this

equipment.

The examples and diagrams in this manual are included solely for illustrative

purposes. Because of the many variables and requirements associated with any

particular installation, Rockwell Automation, Inc. cannot assume responsibility

or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use

of information, circuits, equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without

written permission of Rockwell Automation, Inc. is prohibited.

Throughout this manual, when necessary we use notes to make you aware of

safety considerations.

Important: Identifies information that is critical for successful application and

understanding of the product.

PowerFlex, DriveExplorer, DriveTools SP, DPI, and SCANport are either trademarks or registered trademarks of Rockwell Automation, Inc.

Klixon®is a registered trademark of Sensata Technologies, Inc.

!WARNING: Identifies information about practices or

circumstances that can cause an explosion in a hazardous

environment, which may lead to personal injury or death, property

damage, or economic loss.

!ATTENTION: Identifies information about practices or

circumstances that can lead to personal injury or death, property

damage, or economic loss. Attentions help you identify a hazard,

avoid a hazard, and recognize the consequences.

Shock Hazard labels may be located on or inside the equipment

(e.g., drive or motor) to alert people that dangerous voltage may be

present.

Burn Hazard labels may be located on or inside the equipment

(e.g., drive or motor) to alert people that surfaces may be at

dangerous temperatures.

Summary of Changes

Manual Updates The information below summarizes the changes to the PowerFlex 700H and

700S Installation Instructions, publication PFLEX-IN006, since the March

2006 release.

Change Page

Updated the Normal Duty power ratings Preface-1

Updated the Reference Materials List Preface-1

Added information on installations using single-phase input power 1-2

Updated the Common Bus/Precharge information 1-9

Added a description for the use of output reactors on frame 14 drives 1-2

Updated the 700H I/O board options chart 2-2

Updated the “Auto/Manual Notes” section to include information on enabling manual

mode to allow starts and jogs from the HIM in 2-wire mode

2-12

Added a note to the analog inputs on the 700S Phase II control 4-4

Added terminal wiring illustration for external brake resistor and external brake IGBT

and resistor connections on frame 9 drives

6-6

Updated all Frame 10 dimension drawings to include cable routing information. 7-1 - 7-5

Added a dimension drawing for the frame 10 Motor Control Center (MCC), Enclosure

Codes “B” and “K”

7-4

Updated the instructions for frame 10 Ungrounded, High Resistive Ground or Grounded

B Phase Delta installations

7-9

Updated the Power Terminal Block designations for frame 10 (removed brake option

terminals)

7-14

Updated all Frame 11 dimension drawings to include cable routing information. 8-1 - 8-5

Added a dimension drawing for the frame 11 Motor Control Center (MCC), Enclosure

Codes “B” and “K”

8-4

Updated the instructions for frame 11 Ungrounded, High Resistive Ground or Grounded

B Phase Delta installations

8-9

Updated all Frame 12 dimension drawings to include cable routing information. 9-1 - 9-5

Added a dimension drawing for the frame 12 Motor Control Center (MCC), Enclosure

Codes “B” and “K”

9-4

Updated the instructions for frame 12 Ungrounded, High Resistive Ground or Grounded

B Phase Delta installations

9-9

Updated all Frame 13 dimension drawings to include cable routing information. 10-3 - 10-4

Updated the frame 13 dimensions for the NEMA/UL Type 12 - IP54 Enclosures 10-4

Updated the instructions for frame 13 Ungrounded, High Resistive Ground or Grounded

B Phase Delta installations

10-5

Added Chapter 11 - Frame 14 Installation 11-1

Updated the Agency Certification information for drives with 700H control A-1

Separated the drive ratings information from the drive protection devices - now in

separate tables

A-5,

A-13

Updated the drive rating, fusing and circuit breaker specifications A-13

Added new Appendix B to consolidate the common lifting and mounting instructions B-1

Added the Allen-Bradley 842HR rotary encoder to the list of compatible encoders C-1

Updated wiring diagrams for the Hi-Resolution Encoder C-2

Updated wiring diagrams for Resolvers D-3

Updated wiring diagrams for the MDI board E-3

Added Appendix E on ATEX Approved PowerFlex 700H Drives in Group II Category (2)

Applications with ATEX Approved Motors

F-1

ii Summary of Changes

The information below summarizes the changes to the PowerFlex 700H and

700S Installation Instructions, publication PFLEX-IN006, since the

October, 2004 release.

Change Page

Updated the drive ratings for PowerFlex 700H and 700S Preface-1

Updated the information on installing unbalanced, ungrounded or resistive grounded

distribution systems

1-1

Added information on DC input precharge control wiring 1-10

Updated the “Control Board Slot Designations” table for the new 20C-DG1 digital I/O

option board

2-2

Added drive catalog numbers for 700H control I/O board options 2-2

Updated the “Analog Input, PTC 0-10V Input” wiring example 2-8

Added Chapter 4, “Control Wiring for PowerFlex 700S Drives with Series II Control” 4-1

Updated information on frame 9 operating temperatures 6-2

Updated frame 9 installation instructions for unbalanced, ungrounded or resistive

grounded distribution systems

6-4

Updated frame 10 minimum mounting clearances 7-1

Updated frame 10 operating temperatures 7-2

Added dimensions drawing for frame 10 NEMA/UL Type 12 - IP54 Enclosure 7-5

Updated frame 10 “Moving Control Frame” to show slotted holes in Control Frame 7-6

Updated frame 10 “Removing Protective Covers” to omit screws that were not present. 7-8

Updated frame 10 installation instructions for unbalanced, ungrounded or resistive

grounded distribution systems

7-9

Updated frame 11 minimum mounting clearances 8-1

Updated frame 11 operating temperatures 8-2

Added dimensions drawing for frame 11 NEMA/UL Type 12 - IP54 Enclosure 8-5

Updated frame 11 installation instructions for unbalanced, ungrounded or resistive

grounded distribution systems

8-9

Added Chapter 9, “Frame 12 Installation” 9-1

Added Chapter 10, “Frame 13 Installation” 10-1

Updated the agency certifications A-1

Updated the drive protection specifications A-1

Updated the fusing and circuit breaker specifications A-13, A-13

Added specifications and wiring diagram for using the Stahltronic linear encoder E-3

Table of Contents

Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Summary of

Changes

Manual Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-i

Preface Overview

Drive Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P-1

Enclosure Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P-1

Who Should Use this Manual? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P-2

What Is Not in this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P-2

Reference Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P-2

Manual Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P-3

Drive Frame Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P-4

General Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P-5

Chapter 1 General Installation Information

AC Supply Source Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

General Grounding Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Fuses and Circuit Breakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Power Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

EMC Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Using Input/Output Contactors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

Common Bus/Precharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

Chapter 2 PowerFlex®700H Control Wiring

Reference Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

Auto/Manual Examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Chapter 3 Control Wiring for PowerFlex 700S Drives with Phase I Control

I/O Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Hardware Enable Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

Auxiliary Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

Main Control Board I/O and Encoder Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17

Connecting SynchLink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18

Chapter 4 Control Wiring for PowerFlex 700S Drives with Phase II Control

I/O Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

I/O Terminal Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

I/O Wiring Examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

Hard Enable Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Auxiliary Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

Chapter 5 Communication Options

Communication Module Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Communication Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Chapter 6 Frame 9 Installation

Minimum Mounting Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

Operating Temperatures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

Nameplate Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

Lifting and Mounting Frame 9 Drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4

Removing the Protective Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4

Ungrounded, Unbalanced or High Resistive Ground Installations . . . . . . . . . . . . . . . . . . 6-4

Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

Routing for I/O Wiring and Communication Cabling. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

Chapter 7 Frame 10 Installation

Minimum Mounting Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

Operating Temperatures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3

Lifting and Mounting Frame 10 Drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5

Removing the Protective Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6

Ungrounded, High Resistive Ground or Grounded B Phase Delta Installations. . . . . . . . 7-9

Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14

Chapter 8 Frame 11 Installation

Minimum Mounting Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

Operating Temperatures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

Lifting and Mounting Frame 11 Drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6

Removing the Protective Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6

Ungrounded, High Resistive Ground or Grounded B Phase Delta Installations. . . . . . . . 8-9

Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13

Chapter 9 Frame 12 Installation

Minimum Mounting Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

Operating Temperatures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3

Lifting and Mounting Frame 12 Drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5

Removing the Protective Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6

Ungrounded, High Resistive Ground or Grounded B Phase Delta Installations. . . . . . . . 9-9

Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-14

Chapter 10 Frame 13 Installation

Minimum Mounting Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2

Operating Temperatures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3

Lifting and Mounting Frame 13 Drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5

Ungrounded, High Resistive Ground or Grounded B Phase Delta Installations. . . . . . . 10-5

Removing the Protective Covers from the Converter Unit . . . . . . . . . . . . . . . . . . . . . . . 10-6

Removing the Protective Covers from the Inverter Unit . . . . . . . . . . . . . . . . . . . . . . . . 10-10

Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-12

iii

Chapter 11 Frame 14 Installation

Minimum Mounting Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2

Operating Temperatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-3

Lifting and Mounting Frame 14 Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-8

Ungrounded, High Resistive Ground or Grounded B Phase Delta Installations. . . . . . . 11-9

Removing the Protective Covers from the Converter Unit(s) . . . . . . . . . . . . . . . . . . . . 11-10

Power Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-16

Removing the Protective Covers from the Inverter Units . . . . . . . . . . . . . . . . . . . . . . . 11-16

Frame 14 Circuit Breakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-24

Appendix A Specifications

Drive Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5

Drive Fuse & Circuit Breaker Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-13

Appendix B Lifting and Mounting Instructions

Lifting Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Appendix C PowerFlex 700S Hi-Resolution (Stegmann) Encoder Feedback Option

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Wiring the Hi-Resolution Feedback Option Card to an Encoder . . . . . . . . . . . . . . . . . . . C-2

Appendix D PowerFlex 700S Resolver Feedback Option Card

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1

Wiring the Resolver Feedback Option Card to a Resolver . . . . . . . . . . . . . . . . . . . . . . . . D-3

Appendix E PowerFlex 700S Multi-Device Interface Option Card

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1

Wiring the MDI Option. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-3

Appendix F Instructions for ATEX Approved PowerFlex 700H Drives in Group II Category (2) Appli-

cations with ATEX Approved Motors

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-1

Motor Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-1

Drive Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-2

Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-4

Removing the 20C-DG1 Option Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-6

Verify Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-6

Index

Preface

Overview

Drive Description Frame 9 - 14 PowerFlex® 700H and 700S AC drives are available in the

following normal duty power ratings.

The 700H features a parameter set modeled after the PowerFlex 700 AC

drive. Standard I/O includes either 24V or 115V digital I/O plus analog I/O

NetLinx™ communication options, including DeviceNet™, ControlNet™

and EtherNet/IP networks.

The PowerFlex 700S offers optimized integration for the most demanding

drive control and drive system applications. Available with embedded

high-performance Logix engine (DriveLogix) to produce a highly

functional, cost-effective drive and control solution.

Enclosure Options The following enclosure types are available for PowerFlex 700H and 700S

drives:

Drive AC Input Range HP Range kW Range

700H 380-500V 200-2300 132-1600

525-690V 150-2400 160-2000

700S 380-500V 200-1250 132-800

525-690V 150-1600 160-1500

Drive

Enclosure

Code Enclosure Type NEMA/UL Rating Description

700H A Rittal TS 8

Modular

IP21, NEMA/UL Type 1 Single Door - Freestanding,

Light Grey (RAL 7035)

B MCC Style IP20, NEMA/UL Type 1 Single Door - Freestanding,

Roll-in, Roll-out power

structure

H Rittal TS 8

Modular

IP54, NEMA/UL Type 12(1) Single Door - Freestanding,

Filters in Door and Roof Vent

J No enclosure IP00, NEMA/UL Type Open With Conformal Coated

Circuit Boards

K MCC Style IP20, NEMA/UL Type 1 Single Door - Freestanding,

Roll-in, Roll-out power

structure, with Conformal

Coated Circuit Boards

M Rittal TS 8

Modular

IP21, NEMA/UL Type 1 Single Door - Freestanding,

Light Grey (RAL 7035), with

Conformal Coated Circuit

Boards

N No enclosure IP00, NEMA/UL Type Open –

W Rittal TS 8

Modular w/

Conformal Coat

IP54, NEMA/UL Type 12 Single Door - Freestanding,

Filters in Door and Roof Vent

p-2 Overview

Who Should Use this

Manual?

This manual is intended for qualified personnel. You must be able to mount

and wire Adjustable Frequency AC Drive devices.

What Is Not in this Manual This manual is designed to provide drive mounting and wiring information.

For start-up, programming and troubleshooting information, refer to the

appropriate manual listed below.

Reference Materials Allen-Bradley publications are available on the internet at

www.rockwellautomation.com/literature.

The following manuals are recommended for general drive information:

The following manuals are recommended for detailed PowerFlex 700H

information:

The following manuals are recommended for detailed PowerFlex 700S

information:

700S A Rittal TS 8

Modular

IP21, NEMA/UL Type 1 Single Door - Freestanding,

Light Grey (RAL 7035)

B MCC Style IP20, NEMA/UL Type 1 Single Door - Freestanding,

Roll-in, Roll-out power

structure

N No enclosure IP00, NEMA/UL Type Open –

(1) For replacement filters, refer to the PowerFlex Architecture Class Spare Parts & Options list available at:

http://www.ab.com/support/abdrives/powerflex70/PF7ReleasedParts.pdf

Drive

Enclosure

Code Enclosure Type NEMA/UL Rating Description

Title Publication

Industrial Automation Wiring and Grounding Guidelines 1770-4.1

Wiring and Grounding Guidelines for pulse Width Modulated AC

Drives

DRIVES-IN001…

Preventive Maintenance of Industrial Control and Drive System

Equipment

DRIVES-TD001…

Safety Guidelines for the Application, Installation and Maintenance

of Solid State Control

SGI-1.1

A Global Reference Guide for Reading Schematic Diagrams 100-2.10

Guarding Against Electrostatic Damage 8000-4.5.2

Title Publication

PowerFlex Reference Manual PFLEX-RM001…

PowerFlex 700H Programming Manual 20C-PM001…

Title Publication

PowerFlex 700S with Phase I Control Reference Manual PFLEX-RM002…

PowerFlex 700S with Phase II Control Reference Manual PFLEX-RM003…

PowerFlex 700S with Phase I Control User Manual 20D-UM001…

PowerFlex 700S with Phase II Control User Manual 20D-UM006…

Andere Handbücher für PowerFlex 700S

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockwell Automation Controller Handbücher

Rockwell Automation

Rockwell Automation ALLEN-BRADLEY SMC-3 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1769 CompactLogix Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Logix5000 Betriebsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Micro820 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 7000 Gebrauchsanweisung

Rockwell Automation

Rockwell Automation 1763-L16AWA Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Logix5000 Betriebsanleitung

Rockwell Automation

Rockwell Automation 1769-L30ER Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1756-L72EROMS Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L23E-QB1B Bedienungsanleitung

Rockwell Automation

Rockwell Automation MPMA Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 70 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Dialog Plus 1503D Bedienungsanleitung

Rockwell Automation

Rockwell Automation MicroLogix 1000 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Kinetix VP Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 513 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Samsung NX700 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Rockwell Automation

Rockwell Automation SLC 500 Thermocouple Bedienungsanleitung

Rockwell Automation

Rockwell Automation Micro830 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Samsung NX70 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley LiquiFlo 2.0 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch