Rockwell Automation Allen-Bradley CompactLogix 1769-L32E Bedienungsanleitung

Installation Instructions

CompactLogix Controllers

Catalog Numbers

1769-L32E, 1769-L35E

Use this document as a guide to install the CompactLogix™ controller, which must be the

leftmost module in the first bank of the system. The 1769-L32E and 1769-L35E controllers

offer an integrated EtherNet/IP port.

Topic Page

Important User Information 2

Verify Compatibility 5

Before You Begin 6

Connect the 1769-BA Battery 6

Install a CompactFlash Card (optional) 8

Assemble the System 8

Mount the System 10

Make RS-232 Connections to the Controller 12

Make Ethernet Connections to the Controller 14

Install the Appropriate EDS Files 19

Load the Controller Firmware 19

Select the Controller’s Operating Mode 22

Controller Status Indicators 23

2CompactLogix Controllers

Publication 1769-IN020E-EN-P - December 2011

Important User Information

Solid-state equipment has operational characteristics differing from those of electromechanical equipment.

Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1

available from your local Rockwell Automation sales office or online at

http://www.rockwellautomation.com/literature/) describes some important differences between solid-state

equipment and hard-wired electromechanical devices. Because of this difference, and also because of the wide

variety of uses for solid-state equipment, all persons responsible for applying this equipment must satisfy

themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation®, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many

variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot

assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or death, property

damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal

injury or death, property damage, or economic loss. Attentions help you identify a hazard, avoid

a hazard and recognize the consequences.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, drive or motor, to

alert people that dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, drive or motor, to

alert people that surfaces may reach dangerous temperatures.

IMPORTANT Identifies information that is critical for successful application and understanding of the

product.

CompactLogix Controllers 3

Publication 1769-IN020E-EN-P - December 2011

Environment and Enclosure

Prevent Electrostatic Discharge

WARNING: This equipment is intended for use in a Pollution Degree 2 industrial

environment, in overvoltage Category II applications (as defined in IEC publication

60664-1), at altitudes up to 2000 meters (6562 ft) without derating.

This equipment is considered Group 1, Class A industrial equipment according to

IEC/CISPR Publication 11. Without appropriate precautions, there may be potential

difficulties ensuring electromagnetic compatibility in other environments due to

conducted as well as radiated disturbance.

This equipment is supplied as open-type equipment. It must be mounted within an

enclosure that is suitably designed for those specific environmental conditions that

will be present and appropriately designed to prevent personal injury resulting from

accessibility to live parts. The enclosure must have suitable flame-retardant

properties to prevent or minimize the spread of flame, complying with a flame

spread rating of 5VA, V2, V1, V0 (or equivalent) if non-metallic. The interior of the

enclosure must be accessible only by the use of a tool. Subsequent sections of this

publication may contain additional information regarding specific enclosure type

ratings that are required to comply with certain product safety certifications.

In addition to this publication, see the following:

•Industrial Automation Wiring and Grounding Guidelines, Allen-Bradley®

publication 1770-4.1, for additional installation requirements

•NEMA Standards publication 250 and IEC publication 60529, as applicable, for

explanations of the degrees of protection provided by different types of

enclosure

WARNING: This equipment is sensitive to electrostatic discharge, which can

cause internal damage and affect normal operation. Follow these guidelines when

you handle this equipment:

•Touch a grounded object to discharge potential static.

•Wear an approved grounding wriststrap.

•Do not touch connectors or pins on component boards.

•Do not touch circuit components inside the equipment.

•Use a static-safe workstation, if available.

•Store the equipment in appropriate static-safe packaging when not in use.

4CompactLogix Controllers

Publication 1769-IN020E-EN-P - December 2011

North American Hazardous Location Approval

The following information applies when operating

this equipment in hazardous locations. Informations sur l’utilisation de cet équipement en

environnements dangereux.

Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for

use in Class I Division 2 Groups A, B, C, D, Hazardous

Locations and nonhazardous locations only. Each product is

supplied with markings on the rating nameplate indicating

the hazardous location temperature code. When combining

products within a system, the most adverse temperature

code (lowest "T" number) may be used to help determine the

overall temperature code of the system. Combinations of

equipment in your system are subject to investigation by the

local Authority Having Jurisdiction at the time of installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne conviennent

qu'à une utilisation en environnements de Classe I Division 2

Groupes A, B, C, D dangereux et non dangereux. Chaque produit

est livré avec des marquages sur sa plaque d'identification qui

indiquent le code de température pour les environnements

dangereux. Lorsque plusieurs produits sont combinés dans un

système, le code de température le plus défavorable (code de

température le plus faible) peut être utilisé pour déterminer le

code de température global du système. Les combinaisons

d'équipements dans le système sont sujettes à inspection par les

autorités locales qualifiées au moment de l'installation.

WARNING:

Explosion Hazard -

•Do not disconnect equipment unless

power has been removed or the area is

known to be nonhazardous.

•Do not disconnect connections to this

equipment unless power has been

removed or the area is known to be

nonhazardous. Secure any external

connections that mate to this

equipment by using screws, sliding

latches, threaded connectors, or other

means provided with this product.

•Substitution of components may impair

suitability for Class I, Division 2.

•If this product contains batteries, they

must only be changed in an area known

to be nonhazardous.

AVERTISSEMENT:

Risque d’Explosion –

•Couper le courant ou s'assurer que

l'environnement est classé non dangereux

avant de débrancher l'équipement.

•Couper le courant ou s'assurer que

l'environnement est classé non dangereux

avant de débrancher les connecteurs. Fixer

tous les connecteurs externes reliés à cet

équipement à l'aide de vis, loquets

coulissants, connecteurs filetés ou autres

moyens fournis avec ce produit.

•La substitution de composants peut rendre

cet équipement inadapté à une utilisation

en environnement de Classe I, Division 2.

•S'assurer que l'environnement est classé

non dangereux avant de changer les piles.

CompactLogix Controllers 5

Publication 1769-IN020E-EN-P - December 2011

European Hazardous Location Approval

Verify Compatibility

European Zone 2 Certification (The following applies when the product bears the Ex or EEx

Marking)

This equipment is intended for use in potentially explosive atmospheres as defined by European Union

Directive 94/9/EC and has been found to comply with the Essential Health and Safety Requirements relating

to the design and construction of Category 3 equipment intended for use in potentially explosive

atmospheres, given in Annex II to this Directive.

Compliance with the Essential Health and Safety Requirements has been assured by compliance with EN

60079-15 and EN 60079-0.

WARNING:

•This equipment must be installed in an enclosure providing at least IP54

protection when applied in Zone 2 environments.

•This equipment shall be used within its specified ratings defined by

Allen-Bradley.

•Provisions shall be made to prevent the rated voltage from being exceeded by

transient disturbances of more than 40% when applied in Zone 2

environments.

•Secure any external connections that mate to this equipment by using screws,

sliding latches, threaded connectors, or other means provided with this

product.

•Do not disconnect equipment unless power has been removed or the area is

known to be nonhazardous.

ATTENTION: This equipment is not resistant to sunlight or other sources of UV

radiation.

IMPORTANT

The series B controllers are compatible only with the following:

•Controller firmware revision 20 and later

•RSLogix 5000™software version 20 and later.

Attempting to use controllers with incompatible software and firmware

revisions may result in the following:

•An inability to connect to the series B controller in RSLogix 5000 software

•Unsuccessful firmware upgrades in ControlFLASH™or AutoFlash utilities

6CompactLogix Controllers

Publication 1769-IN020E-EN-P - December 2011

Before You Begin

Consider the following when planning your CompactLogix system:

•The CompactLogix controller is always the leftmost module in the system.

•The controller must be within four modules of the system power supply. Some I/O

modules may be up to eight modules away from the power supply. See the

documentation for your 1769 I/O modules for details.

•The 1769-L32E controller supports as many as 16 I/O modules and the 1769-L35E

controller supports as many as 30 I/O modules. Both controllers can use a maximum of 3

I/O banks with 2 expansion cables.

•Each I/O bank requires its own power supply.

•Only one controller can be used in a CompactLogix system.

•A 1769-ECR right end cap or 1769-ECL left end cap is required to terminate the end of

the communication bus.

Parts List

These components are shipped with the controller.

You may also use these components with the controller.

Connect the 1769-BA Battery

The controller is shipped with the 1769-BA battery that is packed separately. To connect the

battery, follow this procedure.

Component Description

1769-BA battery

1747-KY controller key

If you want to Then use this component

Connect a device to the RS-232 port 1756-CP3 or 1747-CP3 serial cable

Connect a device to the EtherNet/IP port Standard Ethernet cable with RJ-45 connector

Add nonvolatile memory 1784-CF64 or 1784-CF128 Industrial CompactFlash card

ATTENTION: The 1769-BA battery is the only battery you can use with the

1769-L32E and 1769-L35E controllers. The 1747-BA battery is not compatible with

the 1769-L32E and 1769-L35E controllers and may cause problems.

CompactLogix Controllers 7

Publication 1769-IN020E-EN-P - December 2011

1. Remove the battery door by sliding it forward.

2. Insert the battery connector into the connector port.

The connector is keyed to be installed with the correct polarity.

3. Insert the battery into the battery port in the battery door.

4. Slide the battery door back until it clicks into position.

WARNING: When you connect or disconnect the battery, an electrical arc can

occur. This could cause an explosion in hazardous location installations. Be sure

that power is removed or the area is nonhazardous before proceeding.

For safety information on the handling of lithium batteries, including handling and

disposal of leaking batteries, see Guidelines for Handling Lithium Batteries

Technical Data, publication AG-5.4NOV04.

IMPORTANT

Do not remove the plastic insulation covering the battery. The insulation is

necessary to protect the battery contacts.

TIP

At the end of its life, the used battery should be collected

separately from any unsorted municipal waste and

recycled.

Battery

8CompactLogix Controllers

Publication 1769-IN020E-EN-P - December 2011

Install a CompactFlash Card (optional)

The optional industrial CompactFlash card provides nonvolatile memory for a CompactLogix

controller. The card is not required for controller operation.

To install a CompactFlash card, push the locking tab to the right

and insert the industrial CompactFlash card into the socket on the

front of the controller.

The label of the CompactFlash card faces toward the left. Match

the orientation arrow on the card with the arrow on the front of

the controller.

To remove the CompactFlash card, push the locking tab away

from the CompactFlash card and pull the CompactFlash card

from the socket.

Assemble the System

The controller can be attached to an adjacent I/O module or power supply before or after

mounting.

ATTENTION: Do not remove the CompactFlash card while the controller is reading

from or writing to the card, as indicated by a flashing green CF status indicator. This

could corrupt the data on the card or in the controller, as well as corrupt the latest

firmware in the controller.

WARNING: When you insert or remove the CompactFlash card while power is on,

an electrical arc can occur. This could cause an explosion in hazardous location

installations.

Be sure that power is removed or the area is nonhazardous before proceeding.

WARNING: The CompactLogix controller is not designed for removal and insertion

under power.

If you insert or remove the module while backplane power is on, an electrical arc

can occur. This could cause an explosion in hazardous location installations.

Be sure that power is removed or the area is nonhazardous before proceeding.

44732

CompactLogix Controllers 9

Publication 1769-IN020E-EN-P - December 2011

Refer to the illustration when installing a controller.

1. Disconnect line power.

2. Check that the lever of the adjacent module (A) is in the unlocked (fully right) position.

3. Use the upper and lower tongue-and-groove slots (B) to secure the modules together.

4. Move the module back along the tongue-and-groove slots until the bus connectors line

up with each other.

5. Use your fingers or a small screwdriver to push the module’s bus lever back slightly to

clear the positioning tab (C).

6. Move the module’s bus lever fully to the left (D) until it clicks, being sure it is locked

firmly in place.

7. Attach an end-cap terminator (E) to the last module in the system by using the

tongue-and-groove slots as before.

8. Lock the end-cap bus terminator (F).

ATTENTION: When attaching the controller, power supply, and I/O modules, make

sure the bus connectors are securely locked together to be sure of proper electrical

connection.

This equipment is not resistant to sunlight or other sources of UV radiation.

44733

10 CompactLogix Controllers

Publication 1769-IN020E-EN-P - December 2011

Mount the System

Minimum Spacing

Maintain spacing from enclosure walls, wireways, and adjacent equipment. Allow 50 mm (2 in.)

of space on all sides, as shown. This provides ventilation and electrical isolation.

System Dimensions

ATTENTION: During panel or DIN-rail mounting of all devices, be sure that all

debris (such as metal chips or wire strands) is kept from falling into the controller.

Debris that falls into the controller could cause damage while the controller is

energized.

TIP

Compact I/O expansion cables have the same dimensions as the end caps.

Expansion cables can be used on either the right or left end. A 1769-ECR

right-end cap or 1769-ECL left-end cap terminates the end of the communication

bus.

Bottom

Side Side

Top

CompactLogix

Controller

Power Supply

Compact I/O

Module

End Cap

50 mm

(2 in.) 50 mm

(2 in.)

50 mm

(2 in.)

50 mm

(2 in.)

Compact I/O

Module

67.5

(2.68)

52.5

(2.06)

(2.76) 35

(1.38)

118

(4.65)

132

(5.20)

(.58)

52.5

(2.06) 35

(1.38)

(1.38) 35

(1.38) 44734

All dimensions are in mm (in.).

Andere Handbücher für Allen-Bradley CompactLogix 1769-L32E

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockwell Automation Controller Handbücher

Rockwell Automation

Rockwell Automation PowerFlex 700S Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Logix 5000 Series Betriebsanleitung

Rockwell Automation

Rockwell Automation SmartGuard 600 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Dialog Plus 1503D Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 755 Kurzanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Bedienungsanleitung

Rockwell Automation

Rockwell Automation ics triplex AADvance Handbuch

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 70 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley SMC-PLUS Bulletin 150 Bedienungsanleitung

Rockwell Automation

Rockwell Automation SMC FLEX Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley MicroLogix Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Micro820 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley AADvance T9110 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-OA16 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 856T-B24LC Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1756 ControlLogix Betriebsanleitung

Rockwell Automation

Rockwell Automation 9VT201-007HTNNN Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley GuardLogix 5570 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley MicroLogix 1400 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch