Rockwell Automation 1763-L16AWA Bedienungsanleitung

Installation Instructions

MicroLogix 1100 Programmable Controllers

Catalog Numbers 1763-L16AWA, 1763-L16BWA,

1763-L16BBB, 1763-L16DWD

Topic Page

Important User Information 4

Additional Resources 5

Overview 6

Controller Description 7

Hazardous Location Considerations 8

Mounting the Controller 10

Connecting 1762 I/O Expansion Modules 16

Wiring the Controller 17

Specifications 23

Publication 1763-IN001C-EN-P - June 2015

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical equipment.

Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication

SGI-1.1 available from your local Rockwell Automation sales office or online at

http://literature.rockwellautomation.com) describes some important differences between solid state

equipment and hard-wired electromechanical devices. Because of this difference, and also because of the

wide variety of uses for solid state equipment, all persons responsible for applying this equipment must

satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many

variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot

assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING

Identifies information about practices or circumstances that can cause an explosion

in a hazardous environment, which may lead to personal injury or death, property

damage, or economic loss.

IMPORTANT

Identifies information that is critical for successful application and understanding of

the product.

ATTENTION

Identifies information about practices or circumstances that can lead to personal

injury or death, property damage, or economic loss. Attentions help you identify a

hazard, avoid a hazard and recognize the consequences.

SHOCK HAZARD

Labels may be on or inside the equipment (for example, drive or motor) to alert

people that dangerous voltage may be present.

BURN HAZARD

Labels may be on or inside the equipment (for example, drive or motor) to alert

people that surfaces may reach dangerous temperatures.

Publication 1763-IN001C-EN-P - June 2015

Additional Resources

If you would like a manual, you can:

•download a free electronic version from the internet:

http://literature.rockwellautomation.com

•purchase a printed manual by contacting your local Allen-Bradley distributor or

Rockwell Automation representative

Resource Description

MicroLogix 1100 Programmable Controllers User

Manual 1763-UM001

A more detailed description of how to install and use your

MicroLogix 1100 programmable controller and expansion

I/O system.

MicroLogix 1100 Instruction Set Reference

Manual1763-RM001

A reference manual that contains data and function files,

instruction set, and troubleshooting information for

MicroLogix 1100.

Installation Instructions 1762-INxxx Information on installing and using 1762 expansion I/O

modules.

Industrial Automation Wiring and Grounding

Guidelines 1770-4.1

More information on proper wiring and grounding

techniques.

Publication 1763-IN001C-EN-P - June 2015

Overview

MicroLogix 1100 controllers are suitable for use in an industrial environment when installed

in accordance with these instructions. Specifically, this equipment is intended for use in clean,

dry environments (Pollution degree 2(1)) and with circuits not exceeding Over Voltage

Category II(2) (IEC 60664-1).(3)

Install your controller using these installation instructions.

(1) Pollution Degree 2 is an environment where, normally, only non-conductive pollution occurs except that occasionally a

temporary conductivity caused by condensation shall be expected.

(2) Over Voltage Category II is the load level section of the electrical distribution system. At this level transient voltages are

controlled and do not exceed the impulse voltage capability of the product’s insulation.

(3) Pollution Degree 2 and Over Voltage Category II are International Electrotechnical Commission (IEC) designations.

ATTENTION

Do not remove the protective debris strip until after the controller and all other equipment

in the panel near the controller are mounted and wiring is complete. Once wiring is

complete, remove protective debris strip. Failure to remove strip before operating can

cause overheating.

ATTENTION

Electrostatic discharge can damage semiconductor devices inside the controller. Do not

touch the connector pins or other sensitive areas.

debris strip

Publication 1763-IN001C-EN-P - June 2015

Controller Description

Item Description

1 Output Terminal Block

2 Battery Connector

3 Bus Connector Interface to Expansion I/O

4 Battery

5 Input Terminal Block

6LCDDisplay

7 LCD Display Keypad (ESC, OK, Up, Down, Left, Right)

8 Status LEDs

9Memory Module Port Cover(1) -or- Memory Module(2)

(1) Shipped with controller.

(2) Optional equipment.

10 DIN Rail Latches

11 RS-232/485 Communication Port (Channel 0, isolated)

12 Ethernet Port (Channel 1)

ESC OK

Publication 1763-IN001C-EN-P - June 2015

Hazardous Location Considerations

This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D or non-hazardous

locations only. The following WARNING statement applies to use in hazardous locations.

Catalog

Number

Description

Input

Power

Digital

Inputs

Analog

Inputs

Digital

Outputs

Comm.

Ports

1763-L16AWA 120/240V ac (10) 120V ac (2) voltage input

0...10V dc

(6) relay

All individually

isolated

(1) RS-232/485

combo

(isolated)

(1) Ethernet

1763-L16BWA 120/240V ac (6) 24V dc

(4) high-speed

24V dc(1)

(1) The 4 high-speed inputs (inputs 0 through 3) can be used for pulse latching or higher speed counting. Refer to Input

Specifications on page 25 and the MicroLogix 1100 Instruction Set Reference Manual, publication 1763-RM001, for more

information.

(2) voltage input

0 ...10V dc

(6) relay

All individually

isolated

(1) RS-232/485

combo

(isolated)

(1) Ethernet

1763-L16BBB 24V dc (6) 24V dc

(4) high-speed

24V dc(1)

(2) voltage input

0...10V dc

(2) relay (isolated)

(2) 24V dc FET

(2) high-speed

24V dc FET

(1) RS-232/485

combo

(isolated)

(1) Ethernet

1763-L16DWD 12/24V dc (6) 12/24V dc

(4) high-speed

12/24V dc(1)

(2) voltage input

0...10V dc

(6) relay

All individually

isolated

(1) RS-232/485

combo

(isolated)

(1) Ethernet

Publication 1763-IN001C-EN-P - June 2015

WARNING

EXPLOSION HAZARD

•Substitution of components may impair suitability for Class I, Division 2.

•Do not replace components or disconnect equipment unless power has been

switched off.

•Do not connect or disconnect components unless power has been switched off.

•This product must be installed in an enclosure. All cables connected to the

product must remain in the enclosure or be protected by conduit or other means.

•All wiring must comply with N.E.C. article 501-10(b).

•The interior of the enclosure must be accessible only by the use of a tool.

•For applicable equipment (for example, relay modules), exposure to some

chemicals may degrade the sealing properties of the materials used in these

devices:

–Relays, epoxy

It is recommended that you periodically inspect these devices for any degradation

of properties and replace the module if degradation is found.

Publication 1763-IN001C-EN-P - June 2015

Use only the following communication cables in Class I, Division 2 hazardous locations.

Mounting the Controller

General Considerations

Most applications require installation in an industrial enclosure to reduce the effects of

electrical interference and environmental exposure. Locate your controller as far as possible

from power lines, load lines, and other sources of electrical noise such as hard-contact

switches, relays, and ac motor drives. For more information on proper grounding guidelines,

see the Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1.

Environment Classification Communication Cables

Class I, Division 2 Hazardous Environment 1761-CBL-AC00 Series C or later

1761-CBL-AM00 Series C or later

1761-CBL-AP00 Series C or later

1761-CBL-PM02 Series C or later

1761-CBL-HM02 Series C or later

1761-CBL-PH02 Series A or later

1761-CBL-AH02 Series A or later

2707-NC9 Series C or later

1763-NC01 Series A or later

ATTENTION

UNSUPPORTED CONNECTION

Do not connect a MicroLogix 1100 controller to another MicroLogix family controller

such as MicroLogix 1000, MicroLogix 1200, or MicroLogix 1500 using a 1761-CBL-AM00

(8-pin mini-DIN to 8-pin mini-DIN) cable or equivalent.

This type of connection will cause damage to the RS-232/485 communication port

(Channel 0) of the MicroLogix 1100 and/or the controller itself. Communication pins

used for RS-485 communications are alternately used for 24V power on the other

MicroLogix controllers.

Publication 1763-IN001C-EN-P - June 2015

Mounting Dimensions

ATTENTION

Vertical mounting is not supported due to thermal considerations.

ATTENTION

Be careful of metal chips when drilling mounting holes for your controller or other

equipment within the enclosure or panel. Drilled fragments that fall into the controller

could cause damage. Do not drill holes above a mounted controller if the protective

debris strips have been removed.

Dimension 1763-

L16AWA L16BWA L16BBB L16DWD

A 90 mm (3.5 in.)

B 110 mm (4.33 in.)

C 87 mm (3.43 in.)

1763-L16AWA, 1763-L16BWA, 1763-L16BBB, 1763-L16DWD

Publication 1763-IN001C-EN-P - June 2015

Controller Spacing

The controller mounts horizontally, with the expansion I/O extending to the right of the

controller. Allow 50 mm (2 in.) of space on all but the right side for adequate ventilation, as

shown below.

DIN Rail Mounting

The maximum extension of the latch is 14 mm (0.55 in.) in the open position. A flat-blade

screwdriver is required for removal of the controller. The controller can be mounted to

EN50022-35x7.5 or EN50022-35x15 DIN rails. DIN rail mounting dimensions are shown

below.

Dimension Height

A 90 mm (3.5 in.)

B 27.5 mm (1.08 in.)

C 27.5 mm (1.08 in.)

ESC OK

Top

Side

Bottom

Andere Handbücher für 1763-L16AWA

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockwell Automation Controller Handbücher

Rockwell Automation

Rockwell Automation Allen-Bradley 150-E Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 70 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Kinetix VP Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Logix 5000 Series Betriebsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 856T-B24LC Bedienungsanleitung

Rockwell Automation

Rockwell Automation MicroLogix 1000 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Micro820 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1785 PLC-5 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1512A Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Micro800 Bedienungsanleitung

Rockwell Automation

Rockwell Automation powerflex 4 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley AADvance T9110 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Micro830 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1766-L32AWA Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley SMC-3 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley CompactLogix 5370 L2 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation SMC Dialog Plus Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Dialog Plus 1503D Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1756 ControlLogix Betriebsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-OA16 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley LiquiFlo 2.0 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1756-L72EROMS Bedienungsanleitung

Rockwell Automation

Rockwell Automation SMC FLEX Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch