Rose electronics CrystalView HDMI 4K60 Bedienungsanleitung

CrystalView HDMI 4K60

60 HDBase-T Extender

Installation

and

Operation Manual

10707 Stancliff Road

Houston, Texas 77099

Phone: (281) 933-7673

[email protected]

LIMITED WARRANTY

No part of this manual may be reproduced, stored in a retrieval system, or transcribed in any form or any means, electronic or mechanical, including photocopying and

recording, without the prior written permission of Rose Electronics.

manual-crystalview-hdmi-4k60-2018-04-06

Rose Electronics®warrants the CrystalView HDMI 4K60 extender to be in good working order for one year

from the date of purchase from Rose Electronics or an authorized dealer. Should this product fail to be in good

working order at any time during this one-year warranty period, Rose Electronics will, at its option, repair or

replace the Unit as set forth below. Repair parts and replacement units will be either reconditioned or new. All

replaced parts become the property of Rose Electronics. This limited warranty does not include service to

repair damage to the Unit resulting from accident, disaster, abuse, or unauthorized modification of the Unit,

including static discharge and power surges.

Limited Warranty service may be obtained by delivering this unit during the one-year warranty period to Rose

Electronics or an authorized repair center providing a proof of purchase date. If this Unit is delivered by mail,

you agree to insure the Unit or assume the risk of loss or damage in transit, to prepay shipping charges to the

warranty service location, and to use the original shipping container or its equivalent. You must call for a return

authorization number first. Under no circumstances will a unit be accepted without a return authorization

number. Contact an authorized repair center or Rose Electronics for further information.

ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT INCLUDING THE WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO A

PERIOD OF ONE YEAR FROM THE DATE OF PURCHASE, AND NO WARRANTIES, WHETHER EXPRESS

OR IMPLIED, WILL APPLY AFTER THIS PERIOD. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW

LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTIED ABOVE, YOUR SOLE

REMEDY SHALL BE REPLACEMENT OR REPAIR AS PROVIDED ABOVE. IN NO EVENT WILL ROSE

ELECTRONICS BE LIABLE TO YOU FOR ANY DAMAGES INCLUDING ANY LOST PROFITS, LOST

SAVINGS OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF OR

THE INABILITY TO USE SUCH PRODUCT, EVEN IF ROSE ELECTRONICS OR AN AUTHORIZED DEALER

HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY OTHER

PARTY.

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, SO THE ABOVE MAY NOT APPLY TO YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS

WHICH MAY VARY FROM STATE TO STATE.

DECLARATIONS OF CONFORMITY

This is to certify that, when installed and used according to the instructions in this manual, the units listed and

described here are shielded against the generation of radio interferences in accordance with the application of

Council Directives 2014/30/EU and 2014/30/EU.

This equipment has been found to comply with the limits for a Class A digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the interference at their own expense.

The manufacturer complies with the EU Directive 2012/19/EU on the prevention of waste electrical and

electronic equipment (WEEE). The device labels carry a respective marking.

These devices comply with Directive 2011/65/EU of the European Parliament and of the council of 8 June

2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment

(RoHS 2, RoHS II). The device labels carry a respective marking.

TABLE OF CONTENTS

Contents

Disclaimer 1

System Introduction 1

Features 1

Package Contents 2

Compatibility 2

CrystalView HDMI 4K60 Units 3

CrystalView HDMI 4K60 Transmitter 3

CrystalView HDMI 4K60 Receiver 4

Installing the CrystalView HDMI 4K60 Extender 5

Installing the IR Components 5

Safety 6

Maintenance and Repair 7

Technical Support 7

Figures

Figure 1. Transmitter front and rear panels 3

Figure 2. Receiver front and rear panels 4

Figure 3. CrystalView HDMI 4K60 – installation diagram 4

Figure 4. IR transmitter cable 5

Figure 5. IR receiver cable 5

Appendices

Appendix A —Specifications 8

Appendix B —Part Numbers 8

INTRODUCTION

CrystalView HDMI 4K60 Manual 1

Disclaimer

While every precaution has been taken in the preparation of this manual, the manufacturer assumes no

responsibility for errors or omissions. Neither does the manufacturer assume any liability for damages resulting

from the use of the information contained herein. The manufacturer reserves the right to change the

specifications, functions, circuitry of the product, and manual content at any time without notice.

The manufacturer cannot accept liability for damages due to misuse of the product or other circumstances

outside the manufacturer’s control. The manufacturer will not be responsible for any loss, damage, or injury

arising directly or indirectly from the use of this product (See limited warranty).

System Introduction

Thank you for choosing the Rose Electronics CrystalView HDMI 4K60 extender for your ultra high-resolution

video extension needs. This product boosts digital video and audio transmission distance for 1080p signals up

to 330ft (100 m) over a single CATx cable. HDR 4K signals can be extended up to 230ft (70 m).

HDCP support enables uncompressed video from a computer, DVD player, Blu-ray player, or a set-top box to

be displayed on remote monitors, HDTV’s, or video projectors, with full support for high definition 7.1ch audio.

The CrystalView HDMI 4K60 features bidirectional IR remote control extension, as well as full duplex RS-232

extension at baud rates up to 115,200 bps. The system utilizes PoC (Power over Cable), so a single power

supply connected to either the Transmitter or Receiver can power the device at the other end.

The instructions in this manual assume a general knowledge of computer installation procedures, familiarity

with cabling requirements, and some familiarity with HDMI device operation.

Features

■HDMI 2.0a compliant

■Supports 4K2K@60Hz (4:4:4, 8 bits) and HDR 4K2K@60Hz (4:2:0, 10 bits)

■Extends full HD 1080p signal up to 330ft (100 m) and 4K2K@60Hz signal up to 230ft (70 meters)

■PoC (Power over Cable) feature provides for both transmitter and receiver units to be powered by a

single power supply on either end

■Terminal block connectors support full-duplex RS-232 extension at rates to 115,200 bps

■Supports bidirectional IR remote controls at frequencies from 20 KHz to 60 KHz

■Video latency less than 20µs

■Supports HDCP 2.2 and EDID pass through

■HDMI-CEC support

■Supports uncompressed HDMI 7.1 channel digital audio, DTS-HD Master Audio and Dolby TrueHD high

bit rate audio

■Firmware updates provided

■Wall mounted housing design for sturdy installation

CrystalView HDMI 4K60 Manual 2

Package Contents

The package contents consist of the following items:



CrystalView HDMI 4K60 transmitter and receiver units



1 x IR transmitter



1 x IR receiver



1 x 12VDC 2A power adapter with power cord



Installation and operations manual.

Compatibility



HDMI 2.0a



HDCP 2.2



All 3D formats and deep color video



DTS-HD, Dolby TrueHD, and 7.1 channel digital audio



Full Duplex RS-232 to 115,200 baud

All references to HDMI cables in this document refer to the maximum recommended distances for each cable type.

Maximum recommended cable distances should not be exceeded.

MODELS

CrystalView HDMI 4K60 Manual 3

CrystalView HDMI 4K60 Units

The CrystalView HDMI 4K60 comes in a single model. The front and rear views of the transmitter and receiver

units are shown below.

CrystalView HDMI 4K60 Transmitter

CrystalView HDMI 4K60 – transmitter unit front and rear panels

Front Panel

1. LED Indicators: From left to right

Power indicator

Link indicator

HDMI Signal Indicator

Rear Panel

2. Locking power jack: Connect to 12V DC power

supply

3. RJ45: Connect CAT5/5e/6 cable to link to the

receiver unit

4. IR RX: 3.5mm socket for plugging in the IR

receiver cable

5. IR TX: 3.5mm socket for plugging in the IR

transmitter cable

6. RS-232 terminal block: Connect the source RS-

232 left to right – (TX, RX, GND)

7. DIP Switch:

OFF – Normal operation

ON – Firmware update

8. HDMI IN: Connect to the HDMI source with

HDMI male-male cable

Figure 1. Transmitter front and rear panels

CrystalView HDMI 4K60 Manual 4

CrystalView HDMI 4K60 Receiver

CrystalView HDMI 4K60 – receiver unit front and rear panels

Front Panel

9. LED Indicators: From left to right

Power indicator

Link indicator

HDMI Signal Indicator

Rear Panel

10. Locking power jack: Connect to 12V DC

power supply

11. RJ45: Connect CAT5/5e/6 cable to link to the

transmitter unit

12. IR RX: 3.5mm socket for plugging in the IR

receiver cable

13. IR TX: 3.5mm socket for plugging in the IR

transmitter cable

14. RS-232 terminal block: Connect the source

RS-232 left to right – (TX, RX, GND)

15. DIP Switch:

OFF – Normal operation

ON – Firmware update

16. HDMI OUT: Connect to the HDMI display with

HDMI male-male cable

Figure 2. Receiver front and rear panels

Figure 3. CrystalView HDMI 4K60 – installation diagram

Transmitter

Blu-ray Player

Receiver

IR-RX

IR-TX

IR-RX

IR-TX

HDMI

Display

CATx

HDBase-T

INSTALLATION and OPERATION

CrystalView HDMI 4K60 Manual 5

Installing the CrystalView HDMI 4K60 Extender

Installing the CrystalView HDMI 4K60 is a very simple and straightforward process. It is recommended that all

equipment be powered off prior to beginning the installation. The installation steps are given below.

1. Connect the HDMI video source (PC, Set-Top Box, DVD Player) to the HDMI IN connector on the rear

panel of the transmitter.

2. Connect the HDMI display cables to the HDMI OUT connectors on the rear panel of the receiver.

3. Connect the IR receiver to the IR RX connector on the rear panel of the receiver.

4. Connect the IR transmitter to the IR TX connector on the rear panel of the transmitter.

5. Connect a CAT5/5e/6 cable between the transmitter and receiver.

6. Connect the 12VDC power adapter to the power jack of the receiver, or the transmitter.

7. Apply power to the display and the HDMI video source.

Installing the IR Components

IR transmitter Cable

Plug the IR transmitter cable into the 3.5 mm connector on the transmitter unit. The IR transmitter will emit all

IR command signals transmitted by an IR receiver connected to the receiver unit.

Figure 4. IR transmitter cable kit

IR receiver Cable

Plug the IR receiver cable into the 3.5 mm connector on the Receiver unit to receive and transmit the IR control

signals of the remote control device.

Figure 5. IR receiver cable kit

CAUTION! Plugging the IR transmitter or receiver cable into the wrong connector can result in failure of

the IR Extenders. Please ensure that the IR transmitter is only plugged into the connector labeled IR TX the IR

receiver into the connector labeled IR Rx.

SAFETY

CrystalView HDMI 4K60 Manual 6

Safety

The CrystalView HDMI 4K60 Extender, like all electronic equipment, should be used with care. To protect

yourself from possible injury and to minimize the risk of damage to the Unit, read and follow these safety

instructions.



Follow all instructions and warnings marked on this Unit.



Except where explained in this manual, do not attempt to service this Unit yourself.



Do not use this Unit near water.



Assure that the placement of this Unit is on a stable surface.



Provide proper ventilation and air circulation.



Keep connection cables clear of obstructions that might cause damage to them.



Use only power cords, power adapter and connection cables designed for this Unit.



Keep objects that might damage this Unit and liquids that may spill, clear from this Unit. Liquids and

foreign objects might come in contact with voltage points that could create a risk of fire or electrical

shock.



Do not use liquid or aerosol cleaners to clean this Unit. Always unplug this Unit from the power source

before cleaning.

Remove power from the unit and refer servicing to a qualified service center if any of the

following conditions occur:



The connection cables are damaged or frayed.



The Unit has been exposed to any liquids.



The Unit does not operate normally when all operating instructions have been followed.



The Unit has been dropped or the case has been damaged.



The Unit exhibits a distinct change in performance, indicating a need for service.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rose electronics Extender Handbücher

Rose electronics

Rose electronics CrystalView DVI EX Bedienungsanleitung

Rose electronics

Rose electronics CrystalLink USB-3-2-1 Fiber Bedienungsanleitung

Rose electronics

Rose electronics CrystalView DVI Multi Bedienungsanleitung

Rose electronics

Rose electronics CrystalView fiber CRK-1DFM/SUN Bedienungsanleitung

Rose electronics

Rose electronics CrystalLink CLK-1U4TP-100M/PE Bedienungsanleitung

Rose electronics

Rose electronics XtendVue Bedienungsanleitung

Rose electronics

Rose electronics Orion XTender OT2-SLDTXUD1D Bedienungsanleitung

Rose electronics

Rose electronics CrystalView DVI Quad Einrichtungshandbuch

Rose electronics

Rose electronics CrystalView Bedienungsanleitung

Rose electronics

Rose electronics CrystalLink CAT5 Serial Bedienungsanleitung

Rose electronics

Rose electronics CrystalView CAT5 Rack CRV-12SLP Bedienungsanleitung

Rose electronics

Rose electronics CrystalView Micro LT Bedienungsanleitung

Rose electronics

Rose electronics CRK-1USB Bedienungsanleitung

Rose electronics

Rose electronics CrystalView USB2 Bedienungsanleitung

Rose electronics

Rose electronics CrystalView DVI Plus Bedienungsanleitung

Rose electronics

Rose electronics CRK-1P1V Bedienungsanleitung

Rose electronics

Rose electronics CrystalView Extreme Bedienungsanleitung

Rose electronics

Rose electronics CrystalView USB2 Bedienungsanleitung

Rose electronics

Rose electronics CrystalLink USB-3-2-1 Fiber Bedienungsanleitung

Rose electronics

Rose electronics CrystalView DVI Fiber CRK-2DFMPD1D Bedienungsanleitung

Rose electronics

Rose electronics CrystalView DVI Mini Bedienungsanleitung

Rose electronics

Rose electronics CrystalView EX5 Bedienungsanleitung

Rose electronics

Rose electronics CLK-4U2FM-500M Bedienungsanleitung

Rose electronics

Rose electronics VideoSplitter CAT5 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung