Ruijie Reyee RG-EG Series Bedienungsanleitung

Ruijie Reyee RG-EG Series Routers

ReyeeOS 1.216

Web-based Configuration Guide

Document Version: V1.0

Date: February 21, 2023

All rights are reserved in this document and this statement.

Any reproduction, excerption, backup, modification, transmission, translation, or commercial use of this document

or any portion of this document, in any form or by any means, without the prior written consent of Ruijie Networks

is prohibited.

, and other Ruijie networks logos are trademarks of Ruijie Networks.

All other trademarks or registered trademarks mentioned in this document are owned by their respective owners.

Disclaimer

The products, services, or features you purchase are subject to commercial contracts and terms. Some or all of

the products, services or features described in this document may not be within the scope of your purchase or

use. Unless otherwise agreed in the contract, Ruijie Networks does not make any express or implied statement

or guarantee for the content of this document.

Due to product version upgrades or other reasons, the content of this document will be updated from time to time.

Ruijie Networks reserves the right to modify the content of the document without any notice or prompt.

This manual is for reference only. Ruijie Networks endeavors to ensure content accuracy and will not shoulder

any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface

Intended Audience

This document is intended for:

Network engineers

Technical support and servicing engineers

Network administrators

Technical Support

Official website of Ruijie Reyee: https://www.ruijienetworks.com/products/reyee

Technical Support Website: https://ruijienetworks.com/support

Case Portal: https://caseportal.ruijienetworks.com

Community: https://community.ruijienetworks.com

Technical Support Email: [email protected]

Conventions

1. GUI Symbols

Interface symbol

Description

Example

Boldface

1. Button names

2. Window names, tab name, field

name and menu items

3. Link

1. Click OK.

2. Select Config Wizard.

3. Click the Download File link.

Multi-level menus items

Select System >Time.

2. Signs

The signs used in this document are described as follows:

Warning

An alert that calls attention to important rules and information that if not understood or followed can result in data

loss or equipment damage.

Caution

An alert that calls attention to essential information that if not understood or followed can result in function failure

or performance degradation.

Note

An alert that contains additional or supplementary information that if not understood or followed will not lead to

serious consequences.

Specification

An alert that contains a description of product or version support.

3. Note

This manual introduces the product model, port type and CLI for your reference. In case of any discrepancy or

inconsistency between the manual and the actual version, the actual version prevails.

Web-based Configuration Guide 1 Login

1 Login

1.1 Configuration Environment Requirements

1.1.1 PC

Browser: Google Chrome, Internet Explorer 9.0, 10.0, and 11.0, and some Chromium/Internet Explorer kernel-

based browsers (such as 360 Extreme Explorer) are supported. Exceptions such as garble or format error

may occur if an unsupported browser is used.

Resolution: 1024 x 768 or a higher resolution is recommended. If other resolutions are used, the page fonts

and formats may not be aligned, the GUI is less artistic, or other exceptions may occur.

1.2 Default Configuration

Table 1-1 Default Web Configuration

Item

Default

IP address

192.168.110.1

Username/Password

Username and password are not required at your first

1.3 Login to Eweb

1.3.1 Connecting to the Router

You can open the management page and complete Internet access configuration only after connecting a client to

the router in either of the following ways:

Wired Connection

Connect a local area network (LAN) port of the router to the network port of the PC, and set the IP address of the

PC. See Section 1.3.2 Configuring the IPAddress of the Management Client for details.

Wireless Connection

Connect the LAN port to the uplink port on theAP and power on the AP. On a mobile phone or laptop, search for

wireless network @Ruijie-mXXXX (XXXX is the last four digits of the MAC address of each device). In this mode,

you do not need to set the IP address of the management client, and you can skip the operation in Section 1.3.2

Configuring the IPAddress of the Management Client.

1.3.2 Configuring the IP Address of the Management Client

Configure an IP address for the management client in the same network segment as the default IP address of the

device (The default device IP address is 192.168.110.1, and the subnet mask is 255.255.255.0.) so that the

Web-based Configuration Guide 1 Login

management client can access the device. For example, set the IP address of the management client to

192.168.110.200.

1.3.3 Login

Enter the IP address (192.168.110.1 by default) of the router in the address bar of the browser to open the login

page.

Note

If the static IP address of the device is changed, or the device obtains a new dynamic IP address, the new IP

address can be used to access the web management system of the device as long as the management client

and the device are in the same network segment of a LAN.

(1) On the web page, enter the password and click Log In to enter the web management system.

Username and password are not required at your first login and you can configure the router directly.

For device security, you are advised to set the management password after your first login to the web

management system. After the password is set, you need to enter the password when you log in to the web

management system again.

If you forget the IP address or password, hold down the Reset button on the device panel for more than 5

seconds when the device is connected to the power supply to restore factory settings. After restoration, you

can use the default IP address and password to log in.

Caution

Restoring factory settings will delete the existing configuration and you are required to configure the device

again at your next login. Therefore, exercise caution when performing this operation.

Web-based Configuration Guide 1 Login

1.4 Work Mode

The device can work in router mode and AC mode. The system menu pages and configuration function scope

vary depending on the work mode. By default, the EG router works in router mode. To modify the work mode, see

Section 3.1 Switching the Work Mode.

1.4.1 Router Mode

The device supports routing functions such as route-based forwarding and network address translation (NAT),

VPN, and behavior management. It can allocate addresses to downlink devices, forward network data based on

routes, and perform NAT operations.

In the router mode, the device can access the network through Point-to-Point Protocol over Ethernet (PPPoE)

dialing, dynamic IP address, and static IP address. It can also directly connect to a fiber-to-the-home (FTTH)

network cable or an uplink device to provide network access and manage downlink devices.

1.4.2 AC Mode

The device supports Layer 2 forwarding only. The device does not provide the routing and Dynamic Host

Configuration Protocol (DHCP) server functions. By default, the WAN port obtains IP addresses through DHCP.

TheAC mode is applicable to the scenario where the network is working normally. In AC mode, the device serves

as the management controller to access the network in bypass mode and manage the AP.

1.5 Configuration Wizard (Router Mode)

1.5.1 Getting Started

(1) Power on the device. Connect the WAN port of the device to an uplink device using an Ethernet cable, or

connect the device to the optical modem directly.

(2) Configure the Internet connection type according to requirements of the local Internet Service Provider (ISP).

Otherwise, the Internet access may fail due to improper configuration. You are advised to contact your local

ISP to confirm the Internet connection type:

○Figure out whether the Internet connection type is PPPoE, DHCP mode, or static IP address mode.

○In the PPPoE mode, a username, a password, and possibly a service name are needed.

○In the static IP address mode, an IP address, a subnet mask, a gateway, and a DNS server need to be

configured.

1.5.2 Configuration Steps

1. Adding a Device to Network

You can manage and configure all devices in the network in batches by default. Please verify the device count

and network status before configuration.

Note

New devices will join in a network automatically after being powered on. You only need to verify the device

count.

Web-based Configuration Guide 1 Login

If a new device is detected not in the network, click Add to My Network and enter its management password to

add the device manually.

Note

If there is a firewall device in the network, the Firewall Port Config page appears. Select the corresponding

port for configuration.

2. Creating a Network Project

Click Start Setup to configure the Internet connection type and management password.

(1) Network Name: Identify the network where the device is located.

(2) Internet: Configure the Internet connection type according to the requirements of the local ISP.

○DHCP: The router detects whether it can obtain an IP address via DHCPby default. If the router connects

to the Internet successfully, you can click Next without entering an account.

○PPPoE: Click PPPoE, and enter the username, password, and service name. Click Next.

○Static IP: Enter the IP address, subnet mask, gateway, and DNS server, and click Next.

(3) Management Password: The password is used for logging in to the management page.

(4) Country/Region: You are advised to select the actual country or region.

(5) Time Zone: Set the system time. The network time server is enabled by default to provide the time service.

You are advised to select the actual time zone.

Web-based Configuration Guide 1 Login

Click Create Network & Connect. The device will deliver the initialization and check the network connectivity.

The device can access the Internet now. Bind the device with a Ruijie Cloud account for remote management.

Follow the instruction to log in to Ruijie Cloud for further configuration.

Note

If your device is not connected to the Internet, click Exit to exit the configuration wizard.

Please log in again with the new password if you change the management password.

1.5.3 Forgetting the PPPoE Account

(1) Consult your local ISP.

(2) If you replace the old router with a new one, click Obtain Account from Old Device. Connect the old and

new routers to a power supply and start them. Insert one end of an Ethernet cable into the WAN port of the

old router and connect the other end to a LAN port of the new router, and click Obtain. The new router

automatically fetches the PPPoE account of the old router. Click Save to make the configuration take effect.

Web-based Configuration Guide 1 Login

1.6 Configuration Wizard (AC Mode)

1.6.1 Getting Started

Power on the device and connect the device to an uplink device.

Make sure that the device can access the Internet.

1.6.2 Configuration Steps

(1) On the work mode setting page, change the work mode from router mode toAC mode. For details, see Section

3.1 Switching the Work Mode.

Inhaltsverzeichnis

Andere Ruijie Netzwerk-Router Handbücher

Ruijie

Ruijie RG-MTFi-M520 Bedienungsanleitung

Ruijie

Ruijie Reyee RG-EW3200GX PRO Bedienungsanleitung

Ruijie

Ruijie Reyee RG-EG105GWT Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-EW Series Anleitung zur Verwendung

Ruijie

Ruijie Reyee RG-EW1800GX PRO Bedienungsanleitung

Ruijie

Ruijie RG-RSR20-X-28 Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-EG300GH-E Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-EW3000GX PRO Installations- und Betriebsanleitung

Ruijie

Ruijie RG-RSR77 Series Bedienungsanleitung

Ruijie

Ruijie RG-R SR30 Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-EG209GS Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-EW3000GX PRO Bedienungsanleitung

Ruijie

Ruijie RG-RSR77 Series Bedienungsanleitung

Ruijie

Ruijie Reyee RG-EG105GW-X Installations- und Betriebsanleitung

Ruijie

Ruijie RG-RSR30-XA Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-EW300 PRO Bedienungsanleitung

Ruijie

Ruijie RG-RSR10-02E Series Installations- und Betriebsanleitung

Ruijie

Ruijie RSR30-X-SPU10 Installations- und Betriebsanleitung

Ruijie

Ruijie RSR10-01G-T-I Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-EG V2 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RSR10-01G Montageanleitung

Ruijie

Ruijie Reyee RG-EW1200 Bedienungsanleitung

Ruijie

Ruijie RSR10 Series Montageanleitung

Ruijie

Ruijie Reyee RG-EW Series Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung