Samsung SU-2900 Series Bedienungsanleitung

Vacuum

Cleaner

SU-2900 Series

FOR HOUSEHOLD USE ONLY

Operating

Instructions

Read these instructions before operating the vacuum cleaner

※The design and specification may be different depending on the models.

IMPORTANT SAFETY INSTRUCTIONS................................1

ASSEMBLING PARTS.............................................................2

ASSEMBLED VACUUM CLEANER PARTS ........

ATTACHING THE HANDLE..........................2

ATTACHING THE HOSE AND TOOLS.......2

OPERATION........................................................................3

MAINTENANCE..................................................................4

TROUBLESHOOTING.....................................................6

DJ68-00294B(EN)(0.0) 2005.3.15 3:47 PM 페이지1

IMPORTANT

SAFETY INSTRUCTIONS

Thank you for purchasing a Samsung vacuum cleaner. When using an electrical

appliance, basic precautions should always be followed, including the following:

PLEASE READ ALL INSTRUCTIONS

BEFORE USING THIS VACUUM CLEANER.

WARNING: To reduce the risk of fire, electric shock, or injury:

• Do not leave vacuum cleaner unattended when it is plugged in.

• Unplug from outlet when not in use and before servicing.

• Do not use outdoors or on wet surfaces.

• Do not allow children to operate vacuum cleaner or use as a toy.

• Close attention is necessary when used by or near children.

• Use only as described in this manual. Use only manufacturer’s recommended attachments.

• Do not use with damaged cord or plug.

• If vacuum cleaner is not working as it should, or has been dropped, damaged, left outdoors or

dropped in water, take it to a service center.

• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull the cord

around sharp edges or corners. Keep cord away from heated surface.

• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.

• Do not handle vacuum cleaner or plug with wet hands.

• Do not put any object into openings. Do not use with any opening blocked; keep openings free

of dust, lint, hair and anything that may reduce air flow.

• Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts.

• Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.

• Do not use without dirt cup or filters in place. Empty cup and clean filter frequently when

picking up very fine materials such as powder.

• Turn off all controls before unplugging vacuum cleaner.

• Use extra care when cleaning on stairs.

• Do not use to pick up flammable or combustible materials such as gasoline or fine wood

standings or use in areas where they may be present.

• Store your vacuum cleaner indoors in a cool, dry area.

• Avoid picking up hard, sharp objects with the cleaner, they may damage the cleaner.

• Always turn off this appliance before connecting or disconnecting the hose, removing the

bottom plate for maintenance.

• Use only on dry, indoor surfaces, never change the plug in any way.

• Do not modify the polarized plug to fit a non-polarized outlet or extension cord.

• Do not touch the brush roller when it is rotating.

• Keep suction away from your face when using nozzles and pipe.

• Do not pull the power cord around sharp corners and do not allow it to become trapped.

• Unplug before connecting turbine nozzle.(only using turbine-brush model)

SAVE THESE INSTRUCTIONS FOR FUTURE USE.

THIS VACUUM CLEANER HAS A POLARIZED PLUG.

To reduce the risk of electrical shock, this appliance has a polarized plug (one blade wider than

the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the

outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a proper outlet.

DJ68-00294B(EN)(0.0) 2005.3.15 3:47 PM 페이지2

Assembling Parts

Assembled Vacuum Cleaner Parts

The assembled cleaner will look

like the illustration to the left.

1.Handle

2.Power switch

3.Quick release cord hook

4.Post-Motor Filter

5.Crevice tool

6.Handle release

7.Carrying handle

8.Hose

9.Extension wand

10.Combination tool

11.Cyclone-Lever

12.Dirt Cup

13.Filter Cup

14.Upper Tank

15.Louvers

16.Hose Wand Base

17.Height Adjustment Dial

18.Hose Clip

WARNING!

OPERATE THE VACUUM CLEANER ONLY AT THE VOLTAGE SPECIFIED ON THE NAMEPLATE.

Front Back

Step 1. Attaching the Handle

Stand the vacuum upright

and slide the base of the

handle firmly into the

grooves at the top of the

vacuum body.

Insert the screw provided

into the existing hole.

Tighten the screw securely

with a screwdriver.

Before securing the handle,

please check that the

handle is fitted to the

vacuum body and make

sure there’s no gap.

1-1

1-2 1-3

Step 2. Attaching the Hose and Tools

Slide the end of the hose

wand with tabs into the

Hose Wand Base.

Slide the extension

wand and the crevice

tool together into the

storage clip.

1-4 1-5

DJ68-00294B(EN)(0.0) 2005.3.15 3:47 PM 페이지3

Operation

When using the attachments, ensure

the vacuum cleaner is placed firmly

on the floor with the handle in the

upright position. Donotplace the

vacuum on top of furniture or steps as the

brushroller may cause damage.

A. Combination tool:

Two types of cleaning tools are included in

one attachment: rotate for desired tool.

∙Use brush side to dust furniture,

blinds, books, lamps, shelves.

∙Use upholstery side for curtains,

draperies, cushions, fabrics.

B. Crevice tool:

Use in corners, on stairs, baseboards, and

behind furniture.

C. Extension Wand:

Use with desired attachments and narrow

wand for a longer reach.

��option : Mini Turbo Brush

Refer to the separated instruction.

2-1 2-2 2-3

Carrying handle

The cleaner can also be moved by

using the carrying handle.

2-4 2-5

Cleaning lightweight

flexible rugs

Stand on one end of rug and move

cleaner toward other end or edge.

Before reaching edge, push down on

handle. This will lift up the nozzle(front of

cleaner)and will prevent rug from clinging

to cleaner.

Continue to lift front of cleaner so that

when you have reached the edge, it is

completely off the rug. Move cleaner

back to start again, lower front of cleaner,

and use only forward strokes.

Carpet height adjustment

Carpet and rug cleaning takes place at the

nozzle (A).

When it is necessary to raise and lower the

nozzle for various carpet pile heights, rotate the

nozzle control dial (B) to the desired setting.

For maximum cleaning performance, The

following carpet height settings are recommended:

∙Lowest setting: for all types of carpet

∙Higher settings: for very deep pile carpet where

easier pushing effort is desired, while maintaining

good cleaning performance.

Note: If the cleaner is difficult to push, rotate knob to

the next higher setting.

2-6

2-7

2-8

ON-OFF Switch

1.To turn cleaner on, press the

Power switch.

2.To the cleaner off, press the Power

switch again .

Handle positions

The handle of your cleaner has three

positions; upright for storage and

when using cleaning tools; operating

for general operation on carpet and

floors; low for reaching under low

furniture. Step on handle release

pedal to lower handle.

Transporting cleaner

To move your cleaner from room to

room, put the handle in upright

position, tilt the cleaner back on its

rear wheels and push forward.

��option

Cleaning Tool attachments

Attachment tools can be used to

clean furniture or drapes, on stairs

or in corners.

DJ68-00294B(EN)(0.0) 2005.3.15 3:47 PM 페이지4

Maintenance

Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure continued

cleaning effectiveness.

When to empty the Dirt Cup

The dirt cup needs to be emptied when the dirt reaches the "Full" line on the side of the Cup.

If more dirt than this accumulates, your cleaner will not operate effectively.

Note: All new carpet has loose fibers which can fill the Dirt Cup quickly while vacuuming.

Emptying the Dirt Cup

Disconnect cleaner from electrical outlet.

Slide the Cyclone-Lever to the

"Unlock" position.

Grasp handle and pull the Dirt

Cup straight out to remove from

Vacuum.

Empty dirt into garbage container.

Put the Dirt Cup back in the

vacuum and slide the lever to the

"Lock" position.

Cleaning The Circular Filters.

Grasp the Filter Cup located at

the bottom of the Dirt Cup and twist

counterclockwise to unlock and

remove.

3-1 3-2 3-3

Cleaning the Pre/Post-motor Filter

How to clean

Disconnect cleaner from

electrical outlet.

The Pre-Motor Filter protects the

Motor from debris.

It is located underneath the Dirt

Cup and Filter Cup in the

Center of the round part of the

Cyclone-Lever.

Remove the small round Filter

and any debris on top of it. Rinse

well under warm water, then air

dry thoroughly before replacing.

The Post-Motor Filter assists in the

filtation process to return clean

air to the room. It is located

behind the door on the front of the

Cleaner. When the filter becomes dirty,

open the door, remove the filter and

shake the dust off the filter.The Post-

Motor Filter is non-washable therefore

do not wash it in water.

Replace the door by inserting

the tabs on the left side and

snapping the right side into place.

Do not operate cleaner without

Either the Pre-Motor Filter or

Post-Motor Filter in place.

3-5 3-6

Grasp the Circular Filters and twist

to unlock Pull straight up to remove.

Separate the Outer foam and Inner

pleated Circular Filters.

Wash each individually by hand

in warm water. Mild detergent may be

used if desired. Rinse well, then air dry

Thoroughly dry before putting them back

together and replacing in the Filter Cup

The Filter Cup may be washed In warm

water with a mild detergent. Make sure it

is completely dry before reassembling

with fliters.

Post-Motor

Filter

3-4

Pre-Motor

Filter

Unlock

Position Lock

Position

Full Line

DJ68-00294B(EN)(0.0) 2005.3.15 3:47 PM 페이지5

Maintenance

The belt

The belt on your cleaner causes the

agitator to rotate and is important for

the effective operation of the

cleaner. The belt is located under

the bottom plate of the cleaner and

should be checked from time to time

to be sure it is in good condition.

When to replace

Disconnect cleaner from

electrical outlet.

To check belt, remove bottom plate

as shown in “How to replace.”

Replace belt if it is stretched, cut or

broken.

Remove agitator and used belt.

Discard used belt.

3-7 3-8

Insert agitator through belt and place

belt in belt guide (C) on agitator.

Should the agitator shield (D)

become dislodged while replacing

the belt or the agitator, reposition it

as shown, noting the placement of its

belt guide (D)

When to replace the

agitator brush roll

When agitator brushes are worn, the

agitator should be replaced.

To check condition of brushes,

disconnect cleaner from electrical

outlet.

Move the edge of a card across

bottom plate while turning agitator.

To maintain cleaning effectiveness,

replace agitator if brushes do not

touch card.

Grasp agitator firmly and fit it into

position by first sliding the end opposite

the belt into the rectangular slot (F) on

side of cleaner.

Pull other side of agitator (G) into place.

Turn agitator, making sure belt is not

pinched between agitator and agitator

shield.

3-10

With lettering on outside of belt and

positioned as shown in box on (D),

slide new belt over motor pulley (B).

3-9

3-11

How to replace

Disconnect cleaner from electrical

outlet.

Remove bottom plate, belt and

agitator following directions in “The

belt” section beginning with Fig. 3-10.

Discard old agitator.

Continue following the directions in

“The belt” section to reposition belt,

new agitator and bottom plate.

Reposition bottom plate and 4

screws. Tighten screws securely.

3-12 3-13

How to replace

Disconnect cleaner from electrical

outlet.

Place handle in low position and turn

cleaner over so bottom side is up.

Remove the 4 screws as shown with

a screw driver.

DJ68-00294B(EN)(0.0) 2005.3.15 3:47 PM 페이지6

Maintenance

Troubleshooting

Clearing Blockages

Disconnect cleaner from electrical outlet.

The hose on the back of the vacuum cleaner that carries the dirt from the nozzle to the Dirt Cup can

sometimes become clogged. If you notice a change in the sound of the vacuum motor, check for blockages.

Check this list of possible problems and solutions before bringing your vacuum to a service center.

Remove the Hose and disconnect

the Wand.

Check for clogs in the vacuum

base, the wand, the hose and the

suction inlet.

If the blockage persists, turn the

vacuum cleaner off and unplug it.

Remove the bottom plate. Lift up

the short hose in the base of the

vacuum. Inspect the hose for clogs

and remove any obstructions.

Replace the short nozzle hose and

the bottom plate.

Remove Dirt Cup and check Upper

Tank and Louvers.

Check to make sure Louvers are

Installed correctly. To unlock the

Louvers, grasp the rim and turn

Toward the left. Pull straight down

to remove. If the Louvers are

missing or not locked into place,

check and clear the tube in the

center of the Dirt Cup.

3-14 3-16

Problem: Cleaner won’t run

Possible Cause

Possible Solution

∙∙Not firmly plugged in

∙∙Plug unit in firmly

∙∙No voltage in wall plug

∙∙Check fuse or breaker

∙∙Blown fuse or tripped breaker

∙∙Replace fuse or reset breaker

Problem : Poor job of dirt pickup

Possible Cause

Possible Solution

∙∙Full or clogged Dirt Cup

∙∙Empty the Dirt Cup and check for blockages.

∙∙Broken or worn belt

∙∙Replace belt.

∙∙Clogged hose or nozzle

∙∙Clean hose or nozzle area.

∙∙Hole in hose

∙∙Replace hose.

∙∙Dirt Cup improperly installed

∙∙Properly install the Dirt Cup

∙∙Incorrect carpet height setting

∙∙Rotate nozzle control knob to lower setting

∙∙Clogs in air flow passage

∙∙Clear clogs.

Possible Cause

Possible Solution

∙∙Dirt Cup improperly installed

∙∙Re-install the Dirt Cup.

Problem : Dust escapes the Dirt Cup

Possible Cause

Possible Solution

∙∙Strange sound like rushing air

∙∙Check for blockages

Problem : Abnormal sound

Possible Cause

Possible Solution

∙∙Incorrect carpet height setting

∙∙Rotate nozzle control knob to lower setting

Problem : Cleaner hard to push

3-15

DJ68-00294B(EN)(0.0) 2005.3.15 3:47 PM 페이지7

DJ68-00294B(EN)(0.0) 2005.3.15 3:48 PM 페이지8

Aspiradora

SU-2900 Series

PARA USO DOMÉSTICO

SOLAMENTE

Instrucciones

de uso

INSTRUCCIONES DE SEGURIDAD......................................1

PIEZAS DE MONTAJE.............................................................3

PIEZAS ENSAMBLADAS DE LA ASPIRADORA

......

SUJETAR EL MANGO...................................3

SUJETAR LA MANGUERA Y LOS ACCESORIOS

..3

FUNCIONAMIENTO.........................................................4

MANTENIMIENTO ............................................................5

SOLUCIÓN DE PROBLEMAS.....................................7

Gane premios cuando registre su producto en www.samsung.com/global/register

Lea estas instrucciones antes de poner en funcionamie nto la aspiradora

※El diseño y las especificaciones pueden variar dependiendo de los modelos.

DJ68-00294C(ES)(0.0) 2005.3.22 10:28 AM 페이지1

INSTRUCCIONES DE SEGURIDAD

Gracias por comprar una aspiradora Samsung. Cuando se utiliza un artefacto

eléctrico, se debe n tomar precauciones básicas, incluyendo las siguientes:

LEA TODAS LAS ADVERTENCIAS E

INSTRUCCIONES ANTES DE USAR ESTE

ARTEFACT O

Advertencia: Para reducir el riesgo de incendio, descarga eléctrica o lesión:

• Preste atención al aparato cuando esté enchufado. Desenchufe la aspiradora del

tomacorrient e cuando no se utilice o cuando la esté limpiando.

• No la utilice al aire libre o sobre superficies mojadas.

• No permita que se utilice como un juguete. Debe prestarse mucha atención cuando la spirad

ora es utilizada por niños o cerca de los niños.

• Utilícela sólo del modo que se describe en este manual. Utilice sólo los accesorios

recomenda dos por el fabricante.

•

No haga funcionar la aspiradora con el enchufe o el cable dañado. Si no funciona como deber ía,

o si se cayó, se dañó, se dejó a la intemperie o se hundió en el agua, llévela a un servicio té cnico.

• No arrastre la aspiradora tirando del cable, ni utilice el cable como manija. Evite cerrar las pue

rtas sobre el cable o tirar del cable si rodea esquinas o bordes filosos. No pase la aspiradora

so bre su cable. Mantenga el cable alejado de superficies calientes.

•

No desenchufe la aspiradora tirando del cable. Para desenchufarla, tome el enchufe, no el ca ble.

• No toque el enchufe ni la aspiradora con las manos mojadas.

• No introduzca ningún objeto en las aberturas de la aspiradora. No la ponga en

funcionamiento si tiene alguna abertura bloqueada: Manténgala libre de polvo, pelusas,

cabellos y cualquier otro elemento que pudiera reducir el flu jo de aire.

• Mantenga el cabello, la ropa holgada, los dedos y cualquier parte del cuerpo alejados de las a

berturas y piezas móviles.

• No la utilice para recoger elementos encendidos o que emitan humo, tales como cigarrillos, fó

sforos o cenizas calientes.

• No la utilice sin un Contenedor de Suciedad y los filtros.

• Apague todos los controles antes de desenchufar la aspiradora.

• Preste especial atención cuando limpie escaleras.

• No utilice la aspiradora para limpiar líquidos inflamables o combustibles tales como gasolina.

No la utilice en áreas en las que puedan estar presente dichos líquidos.

• Guarde su aspiradora bajo techo en un lugar fresco y seco.

• No utilice cables alargadores ni la enchufe a un tomacorriente con la capacidad de

conducción de corriente inadecuada.

• Evite aspirar objetos punzantes.

• Apague siempre este aparato antes de conectar o desconectar la manguera, cambiar el

Conte nedor de Suciedad, o extraer la placa inferior para su mantenimiento.

• Desenchufe los artefactos eléctricos antes de aspirarlos.

• Este artefacto no está destinado para ser utilizado por niños o ansianos sin supervisión, a me

nos que hayan sido entrenadas adecuadamente por una persona responsable para asegurar

q ue pueden utilizarlo en forma segura.

DJ68-00294C(ES)(0.0) 2005.3.22 10:28 AM 페이지2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Samsung Staubsauger Handbücher

Samsung

Samsung VC-7425VN Bedienungsanleitung

Samsung

Samsung SC9250 Bedienungsanleitung

Samsung

Samsung Q8.0 Bedienungsanleitung

Samsung

Samsung SC61 Series Bedienungsanleitung

Samsung

Samsung VAU5863B Bedienungsanleitung

Samsung

Samsung SC13M31 Series Bedienungsanleitung

Samsung

Samsung SC96P series Bedienungsanleitung

Samsung

Samsung SC06H70x0H Series Bedienungsanleitung

Samsung

Samsung SC4500 Series Bedienungsanleitung

Samsung

Samsung SC4130 Bedienungsanleitung

Samsung

Samsung SC21F60 Series Bedienungsanleitung

Samsung

Samsung SC6530 Bedienungsanleitung

Samsung

Samsung DJ68-00368Q Bedienungsanleitung

Samsung

Samsung SR8730 Bedienungsanleitung

Samsung

Samsung SC4750 User Manual (Windows 7) Bedienungsanleitung

Samsung

Samsung SC6540 Bedienungsanleitung

Samsung

Samsung Jet Bot VR30T85 Series Bedienungsanleitung

Samsung

Samsung SC52 Series Bedienungsanleitung

Samsung

Samsung SC07H40**V SERIES Bedienungsanleitung

Samsung

Samsung SC5480 Bedienungsanleitung

Samsung

Samsung SU33xx SERIES Bedienungsanleitung

Samsung

Samsung SC8020 Bedienungsanleitung

Samsung

Samsung Vacuum cleaner Bedienungsanleitung

Samsung

Samsung VAC7713RP Merkblatt

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch