Sanitaire 600 Series Bedienungsanleitung

Heavy Duty

Upright

Vacuum Cleaner

Household Type

Owner’s Guide

600 Series

Index

Important Safeguards ...................... 2

Service Information .......................... 4

Assemble ......................................... 5

Use................................................... 7

Dust Bag .......................................... 8

Brush Roll Belt ................................. 9

Brush Roll ...................................... 10

Headlight .........................................11

For location of nearest Eureka/

SanitaireWarranty Station or service

information call 1-800-282-2886. www.eureka.com

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions should always be followed,

including the following:

READ ALL INSTRUCTIONS BEFORE USINGTHIS VACUUM CLEANER.

WARNING

To reduce the risk of fire, electric shock, or injury:

•Do not use outdoors or on wet surfaces.

•Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug

the electrical cord when not in use and before servicing.

•Do not allow to be used as a toy.Close attention is necessary when used by or near

children.

•Use only as described in this manual. Use only manufacturer’s recommended

attachments.

•Do not use with damaged cord or plug.If vacuum cleaner is not working as it should,

has been dropped, damaged, left outdoors, or dropped into water, return it to a

service center before using.

•Do not pull or carry by cord, use cord as a handle, close door on cord, or pull cord

around sharp edges or corners. Do not run vacuum cleaner over cord. Keep cord

away from heated surfaces.

•Do not use extension cords or outlets with inadequate current carrying capacity.

•Turn off all controls before unplugging.

•Do not unplug by pulling on cord.To unplug, grasp the plug, not the cord.

•Do not handle plug or vacuum cleaner with wet hands.

•Do not put any object into openings.Do not use with any opening blocked;keep free

of dust, lint, hair, and anything that may reduce airflow.

•This vacuum cleaner creates suction and contains a revolving brush roll.Keep hair,

loose clothing, fingers, and all parts of body away from openings and moving parts.

•Do not pick up anything that is burning or smoking, such as cigarettes, matches, or

hot ashes.

•Do not use without dust bag in place.

•Belt pulleys can become hot during normal use.To prevent burns, avoid touching

the belt pulley when servicing the drive belt.

•Use extra care when cleaning on stairs.

•Do not use to pick up flammable or combustible liquids such as gasoline, or use in

areas where they may be present.

•Store your cleaner indoors in a cool, dry area.

•Keep your work area well lighted.

•Unplug electrical appliances before vacuuming them.

SAVETHESE INSTRUCTIONS

CONSEILS DE SÉCURITÉ

Lors de l’utilisation d’un appareil électrique, quelques précautions élémentaires doivent

être observées, incluant les suivantes:

LISEZTOUTES LES INSTRUCTIONS AVANT D’UTILISERVOTRE ASPIRATEUR.

AVERTISSEMENT

Pour réduire le risque de feu, de choc électrique, ou de blessure:

•Ne pas utiliser à l’extérieur ou sur des surfaces mouillées.

•Fermez le commutateur et débranchez l’appareil lorsque vous ne l’utilisez pas ou

avant le nettoyage ou l’entretien.

•Nepermettezpasqu’ilsoitutilisécommejouet.Uneattentionparticulière estnécessaire

lorsque utilisé par ou près d’un enfant.

•Suivez les recommandations d’utilisation de ce manuel. Utilisez uniquement les

accessoires recommandés par le fabriquant.

•Ne pas utiliser si le cordon ou la fiche sont endommagés.Si l’aspirateur ne fonctionne

pascommeilledevrait,s’ilaétééchappé,s’ilestendommagé,s’ilaétélaisséàl’extérieur

ou échappé dans l’eau, retournez-le à un centre de service avant de utiliser.

•Ne pas le tirer ou le transporter par le cordon, ne pas utiliser le cordon en guise de

poignée. Ne pas fermer une porte sur le cordon ou tirer le cordon sur des coins ou

bordures pointus. Ne pas circuler sur le cordon avec l’aspirateur. Tenir le cordon à

distance des surfaces chauffantes.

•Ne pas utiliser des rallonges ou des prises qui n’ont pas de capacité suffisante pour

transporter le courant.

•Fermer tous les contrôles avant débrancher.

•Ne pas débrancher en tirant sur le cordon. Pour débrancher, tenez la fiche et non le

cordon.

•Ne pas manipuler la fiche ou l’aspirateur avec les mains mouillées.

•Nepas rien insérerdans lesouvertures.Nepasutilisersidesouverturessontbloquées;

assurez-vous qu’elles soient dégagées de poussière, mousse, cheveux ou toute autre

chose qui pourrait réduire le passage de l’air.

•Cetaspirateurcréedelasuccionetcontientunrouleau-brossetournant.Tenirlesparties

mobiles et les ouvertures loin des cheveux, du linge, des doigts et de toute partie du

corps.

•Ne pas ramasser des objets qui brûlent ou fument comme les cigarettes, allumette ou

cendres chaudes.

•N’utilisez pas sans le sac de poussière en place.

•Les poulies du courroie peuvent devenir chaudes pendant l’utilisation normale. Pour

prévenir des brûlures, évitez de touché la poulie du courroie lorsque vous réparez la

courroie.

•Portez une attention particulière lorsque vous nettoyez les escaliers.

•Ne pas utiliser pour ramasser des liquides inflammables ou combustibles comme de

l’essence: Ne pas utiliser dans les endroits où ces liquides pourraient être présents.

•Entreposez votre aspirateur à l’intérieur dans un endroit propre et sec.

•Maintenez un bon éclairage à l’endroit où vous travaillez.

•Débrancher les appareils électriques avant de les balayer.

CONSERVEZ CES INSTRUCTIONS

To reduce the risk of electric shock, this appliance has a polarized plug (one blade

is wider than the other).This plug will fit in a polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified

electrician to install the proper outlet. Do not change the plug in any way.

Afin de réduire le risque de choc électrique, cet appareil est muni d’une fiche

polarisée (une des lames est plus large). Cette fiche ne peut être insérée dans une

prise polarisée que d’une seule façon. Si la fiche ne peut être insérée dans la prise,

retourner la fiche. Si la fiche ne peut toujours pas être insérée dans la prise, faire

installer une prise adéquate par un électricien qualifié. Ne pas modifier la fiche.

GENERAL INFORMATION

The cleaner is designed to pick up dirt and dust particles. Avoid picking up hard or

sharpobjectswiththecleanertoprevent bag tears, hose clogs,andfan bladebreakage

with subsequent motor damage.

Service Information

The instructions in this booklet serve as a guide to routine maintenance.For additional

service information telephone our toll free number for the nearest Eureka/Sanitaire

AuthorizedWarranty Station.You should know the model, type and serial numbers

when you call: USA: 1-800-282-2886

Mexico: 5670-6169

Canada: 1-800-282-2886

If you prefer, you can write to The Eureka Company, Service Division, 807 North Main

Street, Bloomington, Illinois 61701, USA. In Canada write to The Eureka Company,

866LangsDrive, Cambridge, Ontario N3H2N7.RefertoTheSanitaire LimitedWarranty

for complete service information.

DO NOT OIL the motor or the brush roll at any time. The bearings are

permanently lubricated and sealed.

Rating Plate

The model, type, and serial numbers are

indicated on the rating plate located on the

underneath sideofthecleaner.For promptand

complete service information, always refer to

these numbers when inquiring about service.

Model &Type_________________________

Serial No.____________________________

SERVICEINFORMATION:1-800-282-2886

MODEL TYPE SERIAL NO.

VOLTS AMPS. HERTZ

HOW TO ASSEMBLE

CAUTION: Completely assemble vacuum cleaner before using.

2-Part

Bolt

Upper

Cord Hook

Lower

Cord Hook

Bag

Screws

Assembly Packet

is with owner’s guide.

Detail A

Step 1

Attach the Handle

Pushthehandlesectionstogether. Note: Check

to be sure slots in handle are correct, see Detail

Align the holes in the handle. Insert a 2-part

bolt (A) in the center of the handle and tighten.

Push handle into the handle socket so handle

grip curves away from the cleaner. Align the

holes,inserttheother2-partbolt(A)and tighten.

Step 2

Attach Upper Cord Hook

Pull the flexible cord support up toward the top

of the handle.

Insert the lower half of the cord support into the

upper cord hook.

Check to be sure slots in handle are correct,

see Detail A. Place inner tab of cord hook into

handle slot as shown (1) and press hook handle

(2) SNAPPING opposite inner tab into place (3).

Step 3

Attach Lower Cord Hook

Insert the power cord into the lower cord hook.

Snap the hook into the lower handle.

Pull up on the cord to tighten but leave enough

slack near the base so there is no strain on the

cord when the handle is lower.

Step 4

Store Electrical Cord

Wrap the cord around the two cord hooks.

Fasten the plug to the electrical cord to prevent

unwinding.

Step 5

Attach Outer Bag

Important: To provide a good gasket seal,

the bag coupling must seat

firmly against the motor base

and not overlap the furniture

guard.

Holdouterbagwith zipper awayfromthehandle.

Start the bag screws (D) by hand, then tighten

with a screwdriver.

Loop the bag spring onto the bag support hook

on the back of the upper cord hook.

3. SNAP opposite inner

tab into place

1. Place inner tab

into slot 2. Press hook

around handle

Bag

Support

Hook

Flexible

Cord

Support

Lower Cord Hook

Upper Cord Hook

HOW TO USE

The upright vacuum cleaner is designed to be used on multiple types of carpeting. Do

not attempt to use the upright vacuum cleaner on bare floors, as damage to the

floor covering may result. Above the floor cleaning tools are available (optional).

The front of the cleaner has an adjustment that

raises or lowers the cleaner base to match the

type of carpet. With the cleaner cord unplugged,

settheadjustmentto lowest settingformaximum

cleaning.If the cleaner is difficult to push, move

adjustment to next highest setting until cleaner

iscomfortabletopush.Thebrush roll mustreach

the carpet for effective cleaning.

Make each adjustment with

cleaner switch off and cord

disconnected from outlet. For

ease in moving the adjustment

knob, place handle in operating

position and tilt cleaner back to

remove weight from front wheels.

Cleaner Height Setting

WARNING: Avoid injury. Keep loose clothing, hair, fingers, and all other parts

of body away from any moving part (such as the revolving brush).

Turn off the switch and unplug the cleaner before changing the

cleaner height setting.

Handle Adjustment

With the tip of the foot, press down to

release the handle lock located at the left

rear side of the cleaner. Move the handle

and adjust it to the desired position for (1)

storing upright, (2) operating the cleaner at

a comfortable height for the user, and (3)

cleaning underneath low furniture.

Handle Lock

1. Store

2. Use

3.Clean

Underneath

ON/OFF

Power Switch

The power switch is mounted on the motor

hood. A push with the foot turns the motor

ON; push again to turn the motor OFF.

Cord Storage

The cleaner has two convenient cord

storage hooks attached to the handle.

However, some models feature a quick

release cord hook on the upper handle. A

downward twist of the cord hook frees the

cord for quick removal. With either style,

wind the cord around the hooks for storage.

Fasten the plug to the cord to prevent

unwinding.

HOW TO MAINTAIN

The instructions given in this booklet serve as a guide to routine maintenance. To

avoid unnecessary service calls, check the bag, belt and brush roll often.

Disposable Dust Bags

Paper bagsplay a veryimportant role in the efficiencyofavacuum cleaner.Thepurpose

of a paper bag is to trap dirt. But at the same time the paper bag must be porous

enough to allow air to pass through. If the paper bag becomes clogged, no air can

pass through the cleaner and no cleaning can take place, regardless of how powerful

the unit. Change the dust bag frequently. Some fine particles can restrict airflow very

quickly and will decrease performance even before the bag appears to be full. For that

reason,whenvacuumingcarpet fresheners or cleaners,powder,plasterdust,orsimilar

fine substances, the bag may need to be changed more often.

HowTo Change Disposable Dust Bag–Style F & G

NOTE: Turn off the switch and unplug the electrical cord before changing

dust bag. Never operate the vacuum cleaner without the dust bag.

4. Unfold

new

bag.

TOP

BOTTOM

THROAT

❛

5. Place bag

throat on

sleeve.

3. Pull bag

throat off

sleeve.

2. Roll

down

coil

spring.

Look for the symbol.

Ask for GENUINE EUREKA

dust bags–Style F & G.

Micron Filter®Bag Care (Micron Filter Bag is standard on some models)

Because the Micron Filter Bag is an effective filter medium, occasionally trapped dust

particles will need to be cleaned from the inside of it. The dust accumulation can be

vacuumed out with another vacuum or the bag may be removed to shake out. If you

desire, the bag may be hand laundered. The zipper on the bag should be down and

thebagshould remain rightsideout.Use warmwater(150°F65°C) and amilddetergent.

Pre-soaking the bag in a laundry pre-soak is desirable for best cleaning results.Air dry

thoroughly before using.

DO NOT USE AN AUTOMATICWASHER OR DRYER as either will cause abrasion to

the delicate polyester fabric. DO NOT DRY CLEAN as dry cleaning fluids will damage

plastic parts of your bag assembly.

GENUINE

EUREKAPRODUCT

1. Pull

zipper

down.

6. Roll up coil spring.

7. Place paper bag into outer bag.

NOTE: Be certain there are no

folds at the top or bottom of the

paper bag.

8. Lift zipper.

2. Pull up on belt to rotate it off the

motor pulley. Lift up on brush roll

and remove worn belt.

Metal Brush Roll only.

Place rubber end cap covers

(available on select models) over both

end caps (flat side against end cap).

Align holes and secure.

5. Slant brush roll forward so end

caps are in line with slots in cleaner

base.

6. Push brush roll into base.

8. Place slots of bottom plate over

tabs of cleaner base.

9. Seat and secure cam locks.

Brush Roll Belt

The brush roll belt on the upright vacuum cleaner drives the brush to agitate, sweep,

and comb the carpet nap. The belt should be checked regularly to be sure it is in

good condition. Replace the belt if it is stretching, cracking, or slipping. Cut away

any hair or thread wound around the brush roll or the belt pulley because the buildup

could cause the belt to rotate unevenly.

How To Replace A Worn Belt

NOTE: Turn off the switch and unplug the electrical cord before replacing

belt.Belt pulleys can become hot during normal use.To prevent burns,

avoid touching the belt pulley when servicing the drive belt.

IMPORTANT: Improper installation of the brush roll or brush roll belt could

cause carpet or cleaner damage.

1. Release cam locks.

Check for brush wear (see Brush Roll

instructions).

3. Place new belt around brush roll.

4. Align brush roll pulley with belt

guide.

7. Place lower side of belt into belt

guide and pull to stretch the belt

around the left side of motor pulley.

Rotate pulley to secure belt into

groove.

Motor

Pulley

Ask for GENUINE EUREKA

replacement belts, No. 52100

Look for the symbol.

GENUINE

EUREKAPRODUCT

Belt

Guide

Brush Roll

The rotating brush roll sweeps and combs the carpet nap. Keep the brush roll free

from hair and threads so it will continue brushing. When the bristles of the brush roll no

longer touch a straight edge held across the bottom plate, the brush roll is ineffective

because the bristles no longer touch the carpet nap. To maintain the most effective

cleaning, replace the wood brush roll. Install new brush strips on the chromed steel

brush roll (refer to instructions).

How To Replace Worn Brush Strips (chromed steel brush roll)

NOTE: Turn off the switch and unplug the electrical cord before replacing

brush strips.

New brush strips are supplied in sets of two, one long and one short. To replace,

remove bottom plate and belt (see How To Change Belt).Then, grasp center of brush

roll and lift to remove.

Slide in new brush strip of same

length(roundedendfirst).Fit trackon

eithersideinto brushrollslot.Replace

secondbrushstripfromoppositeend

of brush roll.

Replace shaft.

Align indentation on bearing retainer

withbrushstrip on both endsofbrush

roll.

Replace shaft washer.

Position end cap with flat sides of

centerholeover flatsidesofthreaded

shaft.

Tighten locknut.

Align holes and secure rubber end

cap cover flat side against end cap.

Remove rubber end cap cover

(available on select models) from one

end.

Unscrew locknut.

Remove end cap.

Remove shaft washer

(not included in

ball bearing brush roll).

Remove bearing retainer.

Push shaft through opposite end.

Pull out worn brush strip with pliers.

Note:

Shaft washer (D) not included in ball bearing brush roll assembly.

A B C D E

When properly assembled, the brush roll should rotate freely between the two end

caps.Check the condition of the belt;change if necessary.Replace the brush roll, belt,

and bottom plate (see How To Replace A Worn Belt).

Ask for GENUINE EUREKA replacement brush strip.

12 inch No. 52282.

Andere Handbücher für 600 Series

Inhaltsverzeichnis

Andere Sanitaire Staubsauger Handbücher

Sanitaire

Sanitaire SC3680 Series Bedienungsanleitung

Sanitaire

Sanitaire SC6070 Series Bedienungsanleitung

Sanitaire

Sanitaire PRECISION CANISTER SERIES Bedienungsanleitung

Sanitaire

Sanitaire 9050 Series Bedienungsanleitung

Sanitaire

Sanitaire 600 Series Bedienungsanleitung

Sanitaire

Sanitaire TRANSPORT SC535A Bedienungsanleitung

Sanitaire

Sanitaire SC5700 Series Bedienungsanleitung

Sanitaire

Sanitaire System_Pro SP6952 Bedienungsanleitung

Sanitaire

Sanitaire SC688B Bedienungsanleitung

Sanitaire

Sanitaire Quick Kleen SC899 Bedienungsanleitung

Sanitaire

Sanitaire HydroClean SC930A Bedienungsanleitung

Sanitaire

Sanitaire SC888H Handbuch

Sanitaire

Sanitaire 880 Series Bedienungsanleitung

Sanitaire

Sanitaire SC689 Bedienungsanleitung

Sanitaire

Sanitaire SC679J - Maid Saver Upright Vacuum 5.0 Amp... Handbuch

Sanitaire

Sanitaire 4500 Series Bedienungsanleitung

Sanitaire

Sanitaire S107 System_Pro Bedienungsanleitung

Sanitaire

Sanitaire S3680 Series Bedienungsanleitung

Sanitaire

Sanitaire SC6600 Bedienungsanleitung

Sanitaire

Sanitaire Series 3680 Bedienungsanleitung

Sanitaire

Sanitaire MIGHTY MITE S3686A Handbuch

Sanitaire

Sanitaire 200 Series Bedienungsanleitung

Sanitaire

Sanitaire S677A Handbuch

Sanitaire

Sanitaire SC6090 Handbuch

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch