Sartorius Talent Bedienungsanleitung

98648-012-18

Operating Instructions

Sartorius Talent

Sartorius Gem, Gold

Electronic Analytical and Precision

Balances and Precious Metal Scales with EC Type Approval

Contents Warnings and

Safety Precautions

2 Contents

2Warnings and Safety Precautions

3 Initial Verification

4Getting Started

7Operation

7 Basic Weighing Function

8 Calibration/Adjustment

10 Application Programs

10 Toggling Between Weight Units

11 Net-Total Formulation/

Second Tare Memory

12 Counting

13 Weighing in Percent

14 Weigh Averaging

15 Configuring the Balance/

Scale (Menu Codes)

15 Setting the Parameters (Menu Codes)

16 Balance/Scale Operating Menu (Overview)

18 ISO/GLP-compliant Printout

20 Data Interface

21 Error Codes

22 Care and Maintenance

23 Instructions for Recycling

24 Overview

24 Specifications

26 Accessories (Options)

28 Information on EC Verification

30 Declaration of Type Conformity

33 EC Type-approval Certificate

34 Plates and Markings

Safety

GTo prevent damage to the equipment,

please read these operating instructions

carefully before using your balance/scale.

!Do not use this balance/scale in a hazardous

area/location.

!Use only commercially available

non-rechargeable or rechargeable batteries:

8+AA, Mignon

!Make absolutely sure to unplug the

balance/scale from AC power before you con-

nect or disconnect a peripheral device.

!Exposure to excessive electromagnetic

disturbance can cause the readout value to

change. Once the disturbance has ceased, the

instrument can be used again in accordance

with its intended use.

Setting up the Balance/Scale

!Warning when using pre-wired RS-232

connecting cables: The pin assignments

in RS-232 cables purchased from other

manufacturers may be incompatible with

Sartorius balances/scales. Be sure to check

the pin assignment against the chart

on page 20 before connecting the cable,

and disconnect any lines that do not match.

– Connect only Sartorius accessories and

options, as these are optimally designed for

use with your Sartorius balance/scale.

Do not try to solve any problems on your own.

The operator shall be responsible for any mod-

ifications to Sartorius equipment and for any

connections of cables or equipment not sup-

plied by Sartorius and must check and, if nec-

essary, correct these modifications and con-

nections. On request, Sartorius will provide

information on the minimum operating speci-

fications (in accordance with the standards

for defined immunity to interference).

– Do not open the balance/scale housing.

If the seal is broken, this will result

in forfeiture of all claims under the

manufacturer’s warranty.

$The temperature range (°C) indicated

on the verification label may not be

exceeded during operation.

Example:

DT BH 210

+10°C/+30°C

Using Verified Balances/Scales as Legal

Measuring Instruments in the EU*:

The type-approval certificate for verifi-

cation applies only to non-automatic

weighing instruments. For automatic

operation with or without auxiliary

measuring devices, you must comply

with the regulations applicable to the

place of installation.

* Including the Signatories of the Agree-

ment on the European Economic Area

Initial Verification

TE1200-0CE Models:

These models are supplied for use

in legal metrology (legal-for-trade) in

Germany and already verified ex factory.

For use in legal metrology outside

Germany, the balances/scales must be

initially verified for the respective

country at the place of installation.

In such a case, please contact your

Sartorius representative about the

verification procedure.

TE214S-0CE, TE214S-PCE,

TE124S-0CE, TE64-0CE and

GD603-0CE Models:

These models are verified ex factory for

use in the legal metrology within the

European Economic Area upon delivery.

You can use the balance/scale immedi-

ately after:

– Warming up phase (see page 7)

– Adjustment (see page 8)

Always calibrate/adjust the balance/

scale with the weight supplied at

regular intervals and after setting it

up in a new location.

TE512-0CE, TE512-PCE and

GE512-0CE Models

These models are verified ex factory for

use in legal metrology within the Euro-

pean Economic Area upon delivery.

§Before using the balance/scale as a legal

measuring instrument, calibrate and

adjust it at the place of use using the

built-in motorized calibration weight;

for details, see “Calibration/Adjustment.”

Getting Started

Storage and Shipping Conditions

– Do not expose the balance/scale to

extreme temperatures, blows, shocks,

vibration or moisture.

Unpacking the Balance/Scale

GAfter unpacking the balance/scale,

check it immediately for any visible

damage.

$If you see any sign of damage, proceed

as directed in the chapter entitled “Care

and Maintenance,” under the section on

“Safety Inspection”.

$Save the box and all parts of the

packaging until you have successfully

installed your balance/scale in case you

need to return it. Before packing your

balance/scale, unplug all connected

cables to prevent damage.

Equipment Supplied

– Balance/scale

– Weighing pan

– Pan support (only on models with

a round weighing pan)

– Gem tray (only with GE and GD models)

– AC adapter, plug type

Additionally supplied with TE214S,

TE124S, TE64, GD603 models:

– Shield ring

– Shield plate

– Dust cover

– Calibration weight

Installation Instructions

When choosing a location to set up

your balance/scale, observe the

following:

– Avoid placing the balance/scale in

close proximity to a heater or otherwise

exposing the balance/scale to heat or

direct sunlight

– Protect the balance/scale from drafts

that come from open windows or doors

– Avoid exposing the balance/scale to

extreme vibrations during weighing

– Do not expose the balance/scale to

extreme moisture over long periods

Conditioning the Balance/Scale

Moisture in the air can condense

on the surfaces of a cold balance/scale

whenever it is brought into a substan-

tially warmer place.

If you transfer the balance/scale to

a warmer area, make sure to condition it

for about 2 hours at room temperature,

leaving it unplugged from AC power.

Seal on Balances/Scales of Accuracy

Class Kand l:

Legislation requires that a control seal

be affixed to verified balances/scales

of accuracy class Kor l. The control

seal consists of a sticker with the

“Sartorius” logo. If this seal is damaged

or broken, the verification becomes null

and void and the balance/scale must be

re-verified.

Setting up the Balance/Scale

Balances/Scales with an Analytical Draft Shield

GPlace the components listed below inside

the chamber in the order given:

– Shield plate

– Shield ring

– Pan support

– Weighing pan

– Gem tray (only with GD models)

Balances/Scales with a Round Weighing Pan

GPlace the components listed below inside

the chamber in the order given:

– Pan support

– Weighing pan

– Gem tray (only with GE models)

Balances/Scales with a Rectangular Weighing Pan

GPlace the weighing pan on the balance/scale

GGem tray (only with GE models)

Connecting the Balance/Scale to AC Power/

Safety Precautions

Use only original Sartorius AC adapters:

– for Europe: 6971948

GInsert the right-angle plug into the jack

GPlug AC adapter into electrical outlet

The ground terminal is connected to the balance/scale

housing,

which can be additionally grounded for

operation.

Selecting the Line Voltage (Mains Voltage)

(Optional)

Use the following original AC adapters for selecting

the line voltage:

– AC adapter TNG8 order no. 6971951 (universal)

– AC adapter TNG8 order no. 6971952 (for the U.K.)

GUse the switch to toggle between 230 V and 115 V

Leveling the Balance/Scale

Level the balance/scale any time you set it up in

a new location. Use only the 2 front feet of the

balance/scale for leveling.

GTurn the 2 rear feet until they are in position

> In most cases, this will require several adjustment

steps

Anti-theft Locking Device

To protect against theft, use the mounting lug on

the rear panel of the balance/scale.

GSecure the balance/scale at the place of installation,

for example with a chain or a lock

Operation

Basic Weighing Function

Preparation

GTurn on the balance/scale: Press e

GTo change configurations: See the chapter entitled “Configur-

ing the Balance/Scale”

$To tare the balance/scale: Press t

Additional Functions:

GTo turn off the balance/scale: Press e

Warmup Time

$To ensure accurate results, the balance/scale must warm up

for at least 24 hours before operation the first time it is con-

nected to power. Only after this time will the balance/scale

have reached the required operating temperature.

$Models TE214S-0CE, TE214S-PCE, TE124S-0CE, TE64-0CE,

GD603-0CE: Any time the balance/scale has been dis-

connected from power following the initial installation and

warm-up time, it must warm up for at least 30 minutes and

then calibrated/adjusted using the weight supplied before

further operation.

Example

Basic weighing

Step Key (or instruction) Display/Printout

1. Turn on the balance/scale e

Self-test is performed

2. Place container on balance/scale +52.0 g

(here: 52 g)

3. Tare the balance/scale t+0.0 g

4. Place sample in container +150.2 g

on balance/scale (here: 150.2 g)

Available Features

Calibration/adjustment can only be performed when

– there is no load on the balance/scale,

– the balance/scale is tared,

– the internal signal is stable.

If these conditions are not met, an error message is displayed. Otherwise, the weight

required for external calibration/adjustment is displayed.

Calibration/adjustment of verified balances/scales of accuracy class Kor l:

– Calibration/adjustment is blocked (protective cap over menu access switch is sealed)

> Calibration/adjustment is possible only after the seal has been removed. In this case,

the verification becomes null and void and the balance/scale must be re-verified.

Example

Step Key (or instruction) Display/Printout

1. To unblock calibration/adjustment

function, open the cover plate

on the bottom of the balance/scale

and move the menu access switch

to the “open” position

2. Tare the balance/scale t0.0 g

3. Begin calibration t>2 sec. +1000.0

Calibration weight is displayed

without weight unit (here: 1000 g)

4. Place the indicated calibration 1000.0

weight on the balance/scale

After calibration, the calibration +1000.0 g

weight is displayed with wt. unit

5. Remove the calibration weight 0.0 g

Calibration/Adjustment

Calibration/adjustment with internal weight: Models GE/TE512-0CE/PCE

Menu setting 1 5 2 required.

Step Key (or instruction) Display

1. Calibrate/adjust

the unloaded balance/scale

2. Tare the unloaded balance/scale t0.0 g

3. Start calibration/adjustment t(press and hold)

4. Move the selector for the c

motorized weight into the

“calibration/adjustment” position

5. Calibration/adjustment is performed cC

(“CC” flashes on the display)

6. Remove weight:

Return the selector to the

initial position

7. The internal weight is removed

from the weighing system 0.0 g

All application programs can also be used in legal metrology. Calculated weight

values are indicated by one of the following symbols displayed to the right of the

numerical value:

– Percentage = %

– Piece count = pcs

– Other calculated value = o

The application programs for calibrated balances/scales not intended for use in legal

metrology are labeled with a triangle Gin the right side of the display (e.g. averaging).

Toggle between Weight Units

With this application program you can toggle the display of a weight value back and

forth between two weight units.

Configure the “Toggle weight units” application in the operating menu:

See “Configuring the Balance/Scale.” Menu code: 2.1. 2

Menu code Unit Conversion factor Abbr. on

printout

1. 7. 1 3. 1. 1 Grams (o) 1.000 o

on model GD603

1. 7. 2 3. 1. 2 Grams 1.000 g

1. 7. 3 3. 1. 3 Kilograms1) 0.001 kg

1. 7. 4 3. 1. 4 Carats 5.000 ct

1. 7. 13 3. 1. 13 Milligrams2) 1.000.000 mg

ο= Factory setting

Function

§To toggle the display between the 1st and 2nd weight units:

Press the vkey

1) = only for models with readability >10 mg

2) = only for models with readability <1 mg

Application Programs

Andere Handbücher für talent

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sartorius Laborausrüstung Handbücher

Sartorius

Sartorius Proline Bedienungsanleitung

Sartorius

Sartorius Cubis MCA2.7S Bedienungsanleitung

Sartorius

Sartorius VL1005 Bedienungsanleitung

Sartorius

Sartorius Sterisart Universal Pump 16420 Bedienungsanleitung

Sartorius

Sartorius Vivaspin 500 Bedienungsanleitung

Sartorius

Sartorius Cubis MSU116P Bedienungsanleitung

Sartorius

Sartorius Sartorius SWC Bedienungsanleitung

Sartorius

Sartorius Biotrate Bedienungsanleitung

Sartorius

Sartorius YCP06SQ Bedienungsanleitung

Sartorius

Sartorius Sartocheck 4 plus Bedienungsanleitung

Sartorius

Sartorius Vivaspin Turbo 15 RC Bedienungsanleitung

Sartorius

Sartorius Tacta Bedienungsanleitung

Sartorius

Sartorius Flexsafe Pro Bedienungsanleitung

Sartorius

Sartorius IS06BBE-SX Handbuch

Sartorius

Sartorius Cubis MCE Series Bedienungsanleitung

Sartorius

Sartorius Cubis Series Bedienungsanleitung

Sartorius

Sartorius BIOHIT Picus Bedienungsanleitung

Sartorius

Sartorius BioPAT Trace Bedienungsanleitung

Sartorius

Sartorius PICUS Bedienungsanleitung

Sartorius

Sartorius WZG Series Bedienungsanleitung

Sartorius

Sartorius Sartocheck 4 plus Bedienungsanleitung

Sartorius

Sartorius Biozym Picus Bedienungsanleitung

Sartorius

Sartorius 16274 Bedienungsanleitung

Sartorius

Sartorius Midi Plus Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung

Sartorius talent Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken