SDC E72 EntryCheck Bedienungsanleitung

Affix paper template to door and follow template instructions in preparing door.

Install latch.

Pass the cable assembly with connectors through the 3/4” hole, then mount the

exterior housing through door preparation. Make sure that the lock chassis and

latch are properly engaged as shown. (See Figure 2A.)

See template for measurements.

Latch

Figure 2A

MARK

CENTER

FOR

2-1/8”

(54 mm)

HOLE

Door Thickness Gauge

IMPORTANT

PLACE TEMPLATE

ON HIGH EDGE OF

DOOR BEVEL

Mark for

1” dia. (25 mm)

Latch Hole

at Center Line

of Door Thickness

2-3/4 ” (70 mm) BACKSET

DETACH ON DOTTED LINE

5/16” Hole

OUTSIDE

MOUNTING

PLATE

1-5/8” DOOR

CENTER OF

RETRACTOR

1-3/4” DOOR

1-7/8” DOOR

5/16” Hole

1. Locks are factory assembled with a spacer for 1-3/4” door thickness, (when

lock chassis is firmly against ring.)

2. Locks can be adjusted for 1-5/8” to 1-7/8” door thickness. Before installation,

use door

thickness

gauge

on template

as shown, to check lock chassis position.

Center of latch retractor should align with mark on gauge for appropriate

door thickness.

3. If chassis is not on center, screw chassis in or out to align with mark.

If adjusting for doors thinner than 1-3/4” thickness, split spacer must be

removed. Check

that

lever

engages

lever

catch

before

installation.

4. Make

sure

adjust

for

correct

door

thickness.

Latch

retractor

Spacer

SECURITY DOOR CONTROLS

3580 Willow Lane, Westlake Village, CA 91361-4921 • (805) 494-0622 • Fax: (805) 494-8861

www.sdcsecurity.com • E-mail: service@sdcsecurity.com

INSTALLATION INSTRUCTIONS

E72 EntryCheck™

M:\INS\INST-E72.qxd REV B 0202 Page 1

Serial

Number

steel

exterior

backplate

To position latch retractor for proper handing of door opening, line up retaining clip

located on lever handle with the slot in the escutcheon. Depress retaining clip with

pin tool provided. While depressing, rotate chassis 180 deg to desired position.

Pin Tool

Retaining clip

PUSH ALL EXCESS WIRE LENGTHS DOWN THROUGH THE OPENING

AT THE TOP OF THE INSIDE LOWER HOUSING.

1. Attach the battery cover with two finished #8 screws. Battery cover has a

lip which engages the lower inside housing, it is important that this lip be

seated properly to insure correct alignment.

1. Slide the inside lower housing over the lever tube until it has passed over the

lever catch. (Be sure wires are not pinched.)

2. Fasten with two brass #8 screws. Once secure, fasten the finished #8 screw

at the bottom.

Insert 4 AA batteries into battery holder. (Note polarity.)

Note:

All

wire

pairs

are

color

coded

connect

with

colored

pairs.

1. Connect the grey/red wires from the raceway to the grey/red wires from the lever tube.

The two remaining pairs are only for the optional

sensor-array package, as well

as the “reset lock” function. (See page v of the programming guide.)

2. Connect the red/black wires from the raceway to the red/black wires from the battery pack.

3. Place the battery holder over the center grooved stud.Note: The fork, located on the

bottom of the battery holder will clear the lower inside housing.

4. When properly aligned, push down on the battery holder assembly, engaging the upper

part of the hole into the groove of the center stud. This will connect the lower fork with

the center post, giving a very secure fit.

NOTE:

USE

ONLY

ALKALINE

BATTERIES,

DUE

PREDETERMINED POWER SETTINGS IN THE LOCK.

M:\INS\INST-E72.qxd REV B 0202 Page 2

1. Feed the cable assembly with connectors through the backplate and raceway nut.

2. While holding the interior backplate in position, loosely install the two thru-bolts.

3. Tighten the raceway nut on the raceway tube that passes through the door using a

crescent or 7/8” socket wrench .

When this connection is tight, secure the thru-bolts.

4. Tear cable wrap to separate wires.

Remove

screw

from

Battery

Cover

access

backplate.

I.C. Tailpieces For the E72

Conventional Tailpieces For the E72

Part No. For

ER1984 7 pin IC Core Cylinder

ER1981 Spacer to convert 7 pin tailpiece

to use with 6 pin IC core.

Outside

Lever

Conventional Cylinder (Figure A)

1. Align

lever

catch

outside

tube

face

latch

front.

(Fig. A)

2. Tailpiece must be in a vertical position in cylinder. (Fig. A1)

3. Insert cylinder in lever.

4. Press cylinder

retainer into lever until flush with base of lever.

5. Turn key in cylinder 45° in either direction.

6. Slide lever on tube until it stops at the lever

catch.

7. Slightly wiggle and push until lever

engages

lever

catch

and connector.

Conventional Cylinder

Tailpiece in

vertical position

IC Core Cylinder

To Remove IC Core Lever Handle

IC Core Cylinder (Figure B)

1. Push lever on door in horizontal

position until secure.

2. Insert control key (marked with a “C”) into IC core and turn clockwise.

3. Insert tailpiece

(See chart below.) into core. (Fig. B1)

4. With control key in core, insert core fully into lever.

5. Turn control

key

15°

counter-cclockwise to lock cylinder in place.

Remove control

key.

Installing The Levers

Part No. For

E1903 SDC Cylinders

E1903-L Ilco Cylinders

EA1903-C Schlage Cylinders

M:\INS\INST-E72.qxd REV B 0202 Page 3

Tailpiece in

horizontal position

Latch front

Lever catch

Inside

Lever

1. Push lever on door in horizontal position until secure.

Correct Orientation of Spacer

EK 1038 Spacer kit for 1-3/8” doors

Installing IC Core

MARK

CENTER

FOR

2-1/8”

(54 mm)

HOLE

Door Thickness Gauge

IMPORTANT

PLACE TEMPLATE

ON HIGH EDGE OF

DOOR BEVEL

Mark for

1” dia. (25 mm)

Latch Hole

at Center Line

of Door Thickness

2-3/4 ” (70 mm) BACKSET

DETACH ON DOTTED LINE

5/16” Hole

OUTSIDE

MOUNTING

PLATE

1-5/8” DOOR

CENTER OF

RETRACTOR

1-3/4” DOOR

1-7/8” DOOR

5/16” Hole

MARK FOR RACEWAY HOLE

3/4” (19.05 mm)

6-1/2”( 165.1 mm)

SDC • 3580 Willow Ln., Westlake Village, CA 91361 • www.sdcsecurity.com

805-494-0622 • Fax 805-494-8861

M:\INS\INST-E72.qxd REV B 0202 Page 4

E72 Cylindrical Lockset Template

Andere Handbücher für E72 EntryCheck

Andere SDC Türschloss Handbücher

SDC

SDC PD2090A Bedienungsanleitung

SDC

SDC FS23M Series Bedienungsanleitung

SDC

SDC E75 Series Betriebsanleitung

SDC

SDC 1190A Series Bedienungsanleitung

SDC

SDC SK-82 Bedienungsanleitung

SDC

SDC Z7870 Bedienungsanleitung

SDC

SDC Z7600 Series Bedienungsanleitung

SDC

SDC PRO Series Bedienungsanleitung

SDC

SDC E75 Series Bedienungsanleitung

SDC

SDC EntryCheck E75 Series Bedienungsanleitung

SDC

SDC 352 Narrow Line EMLock Bedienungsanleitung

SDC

SDC Z7200R Bedienungsanleitung

SDC

SDC HiTower R7500 Bedienungsanleitung

SDC

SDC E70PS Series Betriebsanleitung

SDC

SDC Spacesaver 1091 ADMR Bedienungsanleitung

SDC

SDC ZY7500 Series Bedienungsanleitung

SDC

SDC Z7500 Series Bedienungsanleitung

SDC

SDC S6300 Series Bedienungsanleitung

SDC

SDC Z7500 Series Bedienungsanleitung

SDC

SDC S6800 Series Kurzanleitung

SDC

SDC Z7700 Series Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

SDC

SDC S6200 Series Bedienungsanleitung

SDC

SDC Z7200 Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Assa Abloy

Assa Abloy effeff 827A-IP Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 10X Line Bedienungsanleitung