SDC Z7870 Bedienungsanleitung

P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7800_70_72_80_82 REV E 09-21 Page 1

Any suggestions or comments to this instruction or

product are welcome. Please contact us through

our website or email engineer@sdcsecurity.com

1. Measure desired height from finished floor, mark a horizontal line on door and door edge.

2. Align template on edge of door with applicable horizontal at height line. Check the chart for drilling trim

holes on template and mark only holes for lock function being installed.

3. Mortise door edge according to measurements on

installation template and drill proper holes for trim.

4. Recess for face plate, the dimension is:

L 8-1/32" x W 1-5/16" x D 7/32".

Height

line

of lever

or knob

7/32"

Z7870/72 & Z7880/Z7882

MORTISE LOCK

of cylinder

of lockcase

of lever

or knob

Vertical centerline

Installation

template

door edge

OPTIONAL

DOOR CORE DRILLING GUIDE

#7000-DG

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM

[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

INSTALLATION INSTRUCTIONS

A. Door Preparation:

P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7800_70_72_80_82 REV E 09-21 Page 2

B. Strike Installation:

1. Align strike template on jamb. Be sure to keep 3/8" distance between lock centerline and strike

centerline. Recess 5/32" for flush fit of strike and dust box.

2. Mortise jamb according to measurement of strike template. Then fit strike and dust box into frame

and secure into place with supplied screws.

1. Make sure the lock hand matches the door hand, use the following diagram to determine the hand of door.

4-7/8"

3-17/32"

Strike

Lock C

3/8"

1" Holes

1-1/8" Deep

Jamb

Left Hand

LHRB

Left Hand

Reverse Bevel

INSIDE OF DOOR

OUTSIDE OF DOOR

Right Hand

RHRB

Right Hand

Reverse Bevel

INSIDE OF DOOR

OUTSIDE OF DOOR

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM

[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

C. Install Lockcase

P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7800_70_72_80_82 REV E 09-21 Page 3

2. Change hand of lock

For RH and RHRB, the catch screw will be on the lock case side. For LH and LHRB, the catch screw will be on the

lock cover side.

Pull out and

turn

1. Change latchbolt handing

If the hand of the latchbolt doesn’t match the door hand, remove the fixing screw and pull the latchbolt out from

lock case. Turn the latchbolt 180 ° to change the handling. Position latchbolt back, into case and fasten it.

Remove

screw

Instructions for changing lock hand:

REX option Locksets are factory set per handing and can’t be changed in the field.

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM

[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

C Install Lockcase (Continued)

1. Insert spindles as shown

E. Install Lever trim

1. Place the reversible spring cage onto the ferrules with arrow pointing in direction of lever rotation.

2. Install outside trim with mounting posts through door and position lever onto the spindle.

3. Install inside spring cage onto the spindle with the arrow pointing in the direction of inside lever rotation.

4. Install inside mounting plate onto spindle. Tighten with provided screw.

5. Cap inside rose over mounting plate.

D. Install Spindles

Reversible spring

cage

Ferrule

Mounting

post Into Mounting

post

P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7800_70_72_80_82 REV E 09-21 Page 4

3. Connect wires as shown on the lock cover diagram.

4. Insert lockcase into mortise cut-out and fasten screws to door.

C. Install Lockcase (Continued)

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM

[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7800_70_72_80_82 REV E 09-21 Page 5

1. Screw Mortise Cylinder into threaded hole of lock case.

2. Tighten the Set Screw against cylinder(s) by turning clockwise as shown.

3. Install Face Plate onto lock case front and fasten with supplied screws.

F. Install Cylinder and Armor Face Plate

6. Screw inside lever into position and tighten lever collar with supplied spanner wrench.

Spanner wrench

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM

[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

E. Install Lever trim (continued)

USE THIS CAM

(ILCO 863M

SCHLAGE “L” CAM

OR EQUIVALENT)

Face Plate

Mortise Cylinder Collar

(Not Provided)

Mortise Cylinder

Set Screw

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM

[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

E. Install for 07 lever trim

F. Install Cylinder and Armor Face Plate

Spanner

wrench

Collar

Spring

Outside Lever Assy

Spindle

Mounting

Plate

Rose

Inside Lever

Spring Cage

Spring

1. Place the spring, collar and then reversible spring cage onto the outside lever assembly with arrows pointing in

direction of lever rotation. Insert spindle into hub of lock case.

2. Install outside lever assembly with mounting posts through door and position lever assembly onto the spindle.

3. Install inside spring cage onto the spindle with the arrows pointing in the direction of inside lever rotation.

4. Install inside mounting plate over spindle and onto the mounting posts of outside assembly. Tighten with provided

screws.

5. Cap inside rose over mounting plate and insert second spring.

6. Screw inside lever into position and tighten lever collar with the supplied spanner wrench.

1. Screw Mortise Cylinder into threaded hole of the lock case.

2. Tighten the Set Screw against cylinder(s) by turning clockwise as shown.

3. Install Face Plate onto the lock case and fasten with supplied screw.

P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7800_70_72_80_82 REV E 09-21 Page 6

FACE PLATE

Mortise Cylinder Collar

(Not Provided)

Mortise Cylinder

Set Screw

USE THIS CAM

(ILCO 863M

SCHLAGE “L” CAM

OR EQUIVALENT)

P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7800_70_72_80_82 REV E 09-21 Page 7

STANDARD WIRING

12 or 24VDC (Locks are voltage specific)

[email protected]; [email protected]

INSTALLATION WIRE DIAGRAM

Model 7870/72 & 7880/82 Series

WHT/BLK

ORG/BLK

YEL/BLK

WHT/RED

ORG/RED

YEL/RED

COM

DEADBOLT STATUS (B)

SPDT 5A@30VDC

(switch polarity shown w/

deadbolt retracted)

REQUEST-TO-EXIT (R)

SPDT 5A@30VDC

(switch polarity shown w/

inside lever released)

Optional Monitoring Outputs From Lock

Chassis

Z7880 (Failsafe) Lock Power (12VDC)

Access control does not engage the outside lever when the

deadbolt is thrown. *Install MOV across coil to protect ACS

electronics, as close as possible to the lock

Z7882 (Failsecure) Lock Power (12VDC)

Access control does not engage the outside lever when the

deadbolt is thrown. *Install MOV across coil to protect ACS

electronics, as close as possible to the lock

MOV*

RED (+)

BLK (-)

Lock

Chassis

N/C

N/O

Access

Control

(N/O)

Pwr

Supply

(-)

WHT

ORG

YEL

COM

LATCH STATUS (L)

SPDT 5A@30VDC

(switch polarity shown w/

latch extended)

 Lock PWR

 Deadbolt Status

 Latch Status

 Request-to-Exit

(REX)

RED (+)

BLK (-)

BLK/BLU

Lock

Chassis

N/C

N/O

Access

Control

(N/C)

Pwr

Supply

(-)

MOV*

Z7880 (Failsafe) Lock Power (24VDC )

Access control does not engage the outside lever when the

deadbolt is thrown. *Install MOV across coil to protect ACS

electronics, as close as possible to the lock

RED (+)

WHT (-)

BLK/BLU

Lock

Chassis

N/C

N/O

Access

Control

(N/C)

Pwr

Supply

(-)

MOV*

Z7882 (Failsecure) Lock Power (24VDC)

Access control does not engage the outside lever when the

deadbolt is thrown. *Install MOV across coil to protect ACS

electronics, as close as possible to the lock

MOV*

RED (+)

WHT (-)

Lock

Chassis

N/C

N/O

Access

Control

(N/O)

Pwr

Supply

(-)

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM

[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

Z7870 (Failsafe) Lock Power (12VDC)

Access control always engages outside lever. *Install MOV

across coil to protect ACS electronics, as close as possible

to the lock

RED (+)

BLK (-)

Lock

Chassis

N/C

N/O

Access

Control

(N/C)

Pwr

Supply

(-)

Z7872 (Failsecure) Lock Power (12VDC)

Access control always engages outside lever. *Install MOV

across coil to protect ACS electronics, as close as possible

to the lock

MOV*

RED (+)

BLK (-)

Lock

Chassis

N/C

N/O

Access

Control

(N/O)

Pwr

Supply

(-)

MOV*

Z7870 (Failsafe) Lock Power (24VDC)

Access control always engages outside lever. *Install MOV

across coil to protect ACS electronics, as close as possible

to the lock

RED (+)

WHT (-)

Lock

Chassis

N/C

N/O

Access

Control

(N/C)

Pwr

Supply

(-)

MOV*

Z7872 (Failsecure) Lock Power (24VDC)

Access control always engages outside lever. *Install MOV

across coil to protect ACS electronics, as close as possible

to the lock

MOV*

RED (+)

WHT (-)

Lock

Chassis

N/C

N/O

Access

Control

(N/O)

Pwr

Supply

(-)

P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7800_70_72_80_82 REV E 09-21 Page 8

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM

[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

INSTALLATION WIRE DIAGRAM

Models with optional connectors

STANDARD WIRING

(NO OPTIONS)

RED

BLK

4 PIN

CONECTOR

WIRING WITH OPTIONS

GREEN COM

DEADBOLT STATUS (B) BLUE N/C

BROWN N/O

GREY COM

REQUEST TO EXIT (R) VIOLET N/O

WHITE COM

LATCH STATUS (L) YELLOW N/C

ORANGE N/O

MOV*

*Install MOV across each coil to protect ACS electronics.

Install as close as possible to the lock

Power

BLACK

RED

MOV*

(-)

(+)

*Install MOV across each coil to protect ACS electronics.

Install as close as possible to the lock

P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7800_70_72_80_82 REV E 09-21 Page 9

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM

[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SDC Türschloss Handbücher

SDC

SDC 180 Series Bedienungsanleitung

SDC

SDC Z7836 Series Bedienungsanleitung

SDC

SDC EntryCheck 918 Bedienungsanleitung

SDC

SDC FS23M Series Bedienungsanleitung

SDC

SDC ZY7500 Series Bedienungsanleitung

SDC

SDC Z7500 Series Bedienungsanleitung

SDC

SDC E75 Series Bedienungsanleitung

SDC

SDC E72 EntryCheck Fehlerbehebungshandbuch

SDC

SDC Z7700 Series Bedienungsanleitung

SDC

SDC HiTower R7500 Bedienungsanleitung

SDC

SDC E70PS Series Betriebsanleitung

SDC

SDC 1291 ADMR Spacesaver Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

SDC

SDC E75 Series Bedienungsanleitung

SDC

SDC 352 Narrow Line EMLock Bedienungsanleitung

SDC

SDC Excel E1200 Series Bedienungsanleitung

SDC

SDC EntryCheck E75 Series Bedienungsanleitung

SDC

SDC Z7800 Series Bedienungsanleitung

SDC

SDC S6100 Series Bedienungsanleitung

SDC

SDC E72 EntryCheck Bedienungsanleitung

SDC

SDC PD2090A Bedienungsanleitung

SDC

SDC 30-4-12 Bedienungsanleitung

SDC

SDC Spacesaver 1091 ADMR Bedienungsanleitung

SDC

SDC Z7600 Series Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Assa Abloy

Assa Abloy effeff 827A-IP Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 10X Line Bedienungsanleitung