Securam ProLogic L01 Bedienungsanleitung

ProLogic L01 Operation Instructions

Document No: EC-0601A-L01-170330

Version No: V1.02

1.0 System Installation

1.1 System Components

1.2 Pairing the EntryPad with the Lock(s)

1.3 Lock and EntryPad Installation

1.4 Installing Battery

1.5 Test Lock Operation

2.0 Lock Operation

2.1 Opening the Lock

2.2 Wrong Code Entry –Lock Out

2.3 Low Battery

3.0 Code Management

3.2 Enrolling New users

3.3 Change Code

3.4 Delete One User

3.5 Delete All Users

3.6 Disable/Enable User

3.7 Obfuscate Code Entry

4.0 System Identification

4.1 System Info

5.0 Manager Mode

5.1 Enable Manager Mode

5.2 Disable Manager Mode

6.0 Data Management

6.1 Encryption Key Set

7.0 Recovering the System –Reset to Default

7.1 Recovery Code Set

7.2 Recover System

7.3 Mechanical Reset

8.0 System Testing

8.1 Cycle Testing

9.0 Menus

9.1 The ProLogic L01 Menus

ProLogic L01 Operation Instructions

IMPORTANT: It is imperative that all programming be completed with the safe

door in its open position, such that the programmer can gain access to the lock

body in the event of an incorrect programming.

1.0 System Installation

1.1 System Components

The system consists of (1) EntryPad –Part # EC-0601A-L01 plus one of the following Lock bodies:

•SwingBolt –Part # EL-0601

•DeadBolt –Part # EL-0701

•SpringBolt –Part #EL-0801

1.2 Pairing the EntryPad and the Lock

SecuRam safe lock systems can operate in two different modes depending upon the type of EntryPad

being used with the lock body. The ProLogic L01 is a digital lock system and therefore the lock must also

be programmed in digital mode. Converting the lock body to digital mode can be completed with the

following the steps:

Step 1: Ensure the battery is connected to the Entry Pad.

Step 2: Ensure the lock cable is disconnected from the lock body.

Step 3: Locate the Reset Hole on the back of the lock (under the QC sticker).

Step 4: Using a paper clip depress the reset button, inside the reset hole, 3 times to dissipate

any latent energy in the lock.

Step 5: Now depress the reset button and hold.

Step 6: While continuing to depress the reset button, connect the lock cable to the lock body.

Step 7: Continue to hold down the reset button for 5 seconds and then release.

Step 8: Verify that the pairing has been completed, by opening the lock with the default code

111111.

Step 9: Press any button on the EntryPad to initiate a lock communication test. The EntryPad

will display the following information:

•Model Number

•Software Version Number

•No. of Users/ No. Users Programmed

•Lock ID#/Host ID#

•Model Name

ProLogic L01 Operation Instructions

Followed by:

Enter a valid code to test the lock.

The Default codes are as follows:

•Super Code (ID00) is 111111

•Manager Code (ID01) is 123456

Upon entry of a valid code, the lock will open. If the lock does not open and the LCD screen

displays the message “Fail to Link with Lock”, repeat the reset procedure. Be sure to hold down

the reset button through steps 5-7.

If you have difficulty resetting the lock, please call SecuRam Tech Support at (805) 988-8088 or email

info@securamsys.com.

1.3 Lock and EntryPad Installation

Included within your installation kit are (2) shoulder bolts and (3) lock mounting bolts.

•Install the shoulder bolts on the safe door in the pre-drilled holes above and below the spindle

hole.

•Now insert the lock cable (attached to the EntryPad) through the spindle hole.

•On the backside of the safe door, you will see the lock mounting plate and the predrilled lock

mounting holes.

•Connect the lock cable to the lock body and position the lock body appropriately on the lock

mounting plate.

•Ensure that the lock cable is positioned so that it lies in the channel on the back of the lock. This

channel is provided to protect the lock cable from damage or crimping during installation.

•Using the provided lock bolts, secure the lock body to the mounting plate.

Note: it is very important to ensure that there is an adequate gap between the lock bolt and the

boltwork. This gap must be 0.125”.

ProLogic L01 Operation Instructions

1.4.1 Installing the Battery –Standard Battery Compartment (located on the back of the EntryPad)

•Connect the battery terminal clip to the 9V battery. (Duracell or Energizer brands are

recommended).

•Position the battery so that the terminals are in the downward position and push the battery

into the battery compartment. See Fig. 1.

•Carefully tuck the excess lock cable into the cavity on the back of the EntryPad and install the

EntryPad on the shoulder bolts. See Fig. 2.

•Be careful not to crimp or damage the lock cable upon EntryPad installation.

1.4.2 Installing the Battery –SureLock Battery Compartment (removable battery compartment)

Locate the SureLock Battery Compartment at the 5 o’clock position of the EntryPad. See Fig.

•Release the latch of the battery compartment, by pulling lever downward. See Fig 4.

•Pull out the battery compartment from the bottom of the EntryPad. See Fig 5.

•Install a new 9V alkaline battery (Duracell or Energizer brands are recommended) into the

compartment. The battery compartment will only receive the battery when the positive and

negative terminals are oriented correctly. See Fig. 6

•Put the battery compartment back into the EntryPad. Push the latch of the battery

compartment up until it snaps closed. See Fig. 3

ProLogic L01 Operation Instructions

1.5 Testing the Lock Operation

The ProLogic L01 comes with two factory default codes:

•Super Code (ID00) is 111111

•Manager Code (ID01) is 123456

Enter one of the valid codes to verify the communication between the lock and EntryPad. The lock will

open.

2.0 Lock Operation

Upon initial power up, the LCD screen starts a communications test as shown below:

•Including Model Number

•Software Version Number

•No. of Users/ No. Users Programmed

•Lock ID#/Host ID#

•Model Name

After this initial power up it will also check to ensure that the system is communicating correctly. The

display will read “Link with Lock OK”.

If the Display reads: “Fail to Link with Lock” proceed to Section 1.2 entitled “Pairing the Entrypad and the

Lock”

2.1 Opening the Lock

The safe lock system has two default codes installed as follows:

•Super Code (ID00) 1-1-1-1-1-1

•Manager Code (ID01) 1-2-3-4-5-6

Step 1: Enter a valid code –for example 1-1-1-1-1-1.

The display will read “ID00 Verified”.

And the Lock will open.

The display will read:

The lock will relock after 6 seconds.

Note: Time to relock is hard coded and cannot be changed.

ID00

ProLogic L01 Operation Instructions

2.2 Wrong Code Entry –Lock Out

If an invalid code is entered, the following message will be displayed:

If 4 invalid codes are entered consecutively, the safe lock will enter

The display will then report the length of time remaining in the Lock Out period every 15 seconds until it

has expired

After the 4 minute Lock out period, the following message will be displayed, you can now enter a valid

code to open the safe lock.

Enter a valid code to open the lock.

Note: If an invalid code is entered at this point, the lock will only accept 2 invalid entries before it goes

back into the 4 minute Lock out period.

2.3 Low Battery Alert

The display will alert a low battery condition when the battery voltage reaches 5.4±0.2V.

ProLogic L01 Operation Instructions

PLEASE REPLACE THE BATTERY IMMEDIATELY. Operations, such as enrolling or deleting, are not

permitted with low battery condition.

Use one 9V alkaline battery. Manufacturer recommends to use DuracellTM or Energizer® Alkaline

batteries.

3.0 Code Management

The ProLogic L01 comes with two default codes:

•Super Code (ID00) is 111111

•Manager Code (ID01) is 123456

It is strongly recommended that both these default codes are changed before the lock system is put into

service.

The ProLogic L01 has the capability to add one additional user code, in addition to the default codes.

•ID00 is the Super Code –opens the lock, preforms programming and has the ability to turn on

Manager Mode. By default this code is preprogrammed as 1-1-1-1-1-1.

•ID01 is the Manager Code –opens the lock and preforms programming functions. By default this

code is preprogrammed as 1-2-3-4-5-6.

•ID02 is a User Code.

3.1 Enrolling New Users

Step1: Press the Menu/OK button.

Step 2: Using the and , scroll to the System Menu and Press Menu/OK

Step 3: The display will prompt you to enter a valid Administrator code

Enter either the Super Code (ID00) or the Manager Code (ID01). The “Select Menu” message will be

displayed as follows:

Step 4: Scroll to the menu selection “Enroll New User” and Press OK

Step 5: The following informational screens will appear:

ProLogic L01 Operation Instructions

Step 6: Now enter a 6 digit code

Step 7: Repeat new code

Step 8: System will verify that code has been saved.

The new code is now enrolled and available to be used to open the lock

3.2 Change Code

This programming sequence is used to change any code.

Step1: Press the Menu/OK button

Step 2: Using the and , scroll to the System Menu and Press Menu/OK

Step 3: The display will prompt you to enter a valid code. Enter the code to be changed The

“Select Menu” message will be displayed as follows:

Step 4: Scroll to the menu selection “Change Code” and Press OK

Step 5: The display will show this message on the display “Set Code of IDXX” to be changed.

ProLogic L01 Operation Instructions

Step 6: Enter the new 6 digit code.

Step 7: Repeat the new code.

The New Code has now been saved and is available for use.

3.3 Delete One User

Step1: Press the Menu/OK button

Step 2: Using the and , scroll to the System Menu and Press Menu/OK.

Step 3: The display will prompt you to enter a valid code. Enter either the Super Code (ID00) or

the Manager Code (ID01).

The “Select Menu” message will be displayed as follows:

Step 4: Scroll UP to the menu selection “Delete One User” and Press OK

Step 5: Press OK

Step 6: The system will ask to confirm the deletion. Press OK.

This User Code is now deleted from the system.

3.4 Delete All Users

This feature is used to delete all users from the system. Upon executing this command, ID02 will be

deleted and Manager Code will be reset as follows:

ProLogic L01 Operation Instructions

Manager Code (ID01) is 123456

Note: Super Code will not be changed.

Step1: Press the Menu/OK button

Step 2: Using the and , scroll to the System Menu and Press Menu/OK.

Step 3: The display will prompt you to enter a valid code. Enter either the Super Code (ID00) or

the Manager Code (ID01). The “Select Menu” message will be displayed as follows:

Step 4: Scroll UP to the menu selection “Delete All Users” and Press OK.

Step 5: The system will request a Confirmation. Press OK.

The system will verify that all User Codes have been deleted.

The only remaining codes will be as follows:

•Manager Code (ID01) is 123456

•Super Code (ID00) will remain unchanged.

3.5 Disable/Enable User Codes

This feature would be used in order to disable a user code as opposed to deleting it. Disable/Enable

user codes options may be used when a user’s access rights are temporarily revoked. (I.e. the user may

be on vacation or otherwise away from the business.)

After the code has been disabled, it can be re-enabled at a later time, following the same process by

selecting “Enable User”.

Step1: Press the Menu/OK button.

Step 2: Using the and , scroll to the System Menu and Press Menu/OK.

Inhaltsverzeichnis

Andere Securam Sperren Handbücher

Securam

Securam SafeLogic TopLit Series Bedienungsanleitung

Securam

Securam SafeLogic Basic Bedienungsanleitung

Securam

Securam ProLogic B22 Bedienungsanleitung

Securam

Securam ProLogic L02-C Bedienungsanleitung

Securam

Securam ProLogic L22 Bedienungsanleitung

Securam

Securam ProLogic L66 Bedienungsanleitung

Securam

Securam ProLogic L22 Bedienungsanleitung

Securam

Securam SafeLogic Basic Series Bedienungsanleitung

Securam

Securam SH-TB01 Bedienungsanleitung

Securam

Securam SCANLOGIC FPC-1808-II-MB Bedienungsanleitung

Securam

Securam EM-1701A-R Bedienungsanleitung

Securam

Securam ProLogic B01 Bedienungsanleitung

Securam

Securam V8 Technisches Handbuch

Securam

Securam SH-WB01 Bedienungsanleitung

Securam

Securam ScanLogic B22 Bedienungsanleitung

Securam

Securam SafeLogic C10 D-Drive Bedienungsanleitung

Securam

Securam SafeLogic Xtreme Betriebsanleitung

Securam

Securam SafeLogic Basic Bedienungsanleitung

Securam

Securam D Series Bedienungsanleitung

Securam

Securam ScanLogic Optical Installationshandbuch

Securam

Securam ScanLogic D66 Bedienungsanleitung

Securam

Securam MANAGER Series Bedienungsanleitung

Securam

Securam SafeLogic Xtreme Bedienungsanleitung

Securam

Securam SafeLogic Basic Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung

Metra Electronics

Metra Electronics Door Access Terminal Combo Bedienungsanleitung