Securam ProLogic L02-C Bedienungsanleitung

ProLogic L02-C Operation Instructions

Document No: EC-0601A-L02-C-160617

Version No: V1.01

1.0 System Installation

1.1 System Components

1.2 Pairing the EntryPad with the Lock(s)

1.3 Lock and EntryPad Installation

1.4 Installing Battery

1.5 Test Lock Operation

2.0 Lock Operation

2.1 Opening the Lock

2.2 Opening the Lock in Time Delay

2.3 Opening the Lock in Dual Control

2.4Opening the Lock with a Multi-Lock System

3.0 Code Management

3.1 Code Length Options

3.1.1 PW L –6 / Users 10

3.1.2 PW L –8 / Users 30

3.1.3 PW L –6 / Users 30

3.2 Enrolling New users

3.3 Change Code

3.4 Delete One User

3.5 Delete All Users

3.6 Disable/Enable User

3.7 Obfuscate Code Entry

4.0 System Identification

4.1 System Info

5.0 Time Delay

5.1 Set/Cancel Time Delay

5.2 Setting Time Delay Override Users

6.0 Single or Dual Control

6.1 Enable Dual Mode

6.2 Dual Mode Group ID

7.0 Manager Mode

7.1 Enable Manager Mode

7.2 Disable Manager Mode

8.0 Door Management

8.1 Configuring a Multi-lock system

8.2 Set Number of Locks

8.3 Authorize Locks

8.4 Enable Sequence

9.0 Data Management

9.1 Encryption Key Set

10.0 Recovering the System –Reset to Default

10.1 Recovery Code Set

10.2 Recover System

10.4 Mechanical Reset

11.0 System Testing

11.1 Cycle Testing

12.0 Menus

12.1 The ProLogic L02-C Menus

IMPORTANT: It is imperative that all programming be completed with the safe

door in its open position, such that the programmer can gain access to the lock

body in the event of an incorrect programming.

ProLogic L02-C Operation Instructions

1.0 System Installation

1.1 System Components

The system consists of (1) EntryPad –Part # EC-0601A-L02-C plus (1) or more Lock bodies as follows:

SwingBolt –Part # EL-0601

SwingBolt with Status Sensor –Part # EL-0601-S

DeadBolt –Part # EL-0701

SpringBolt –Part #EL-0801

Note: The ProLogic L02-C can control up to 4 locks when used in conjunction with the Expansion Box –

Part # CB11-1T4. (If setting up a multi-lock system, please refer to Section 10.2 –Multi-Lock Systems)

1.2 Pairing the EntryPad and the Lock

SecuRam safe lock systems can operate in two different modes depending upon the type of EntryPad

being used with the lock body. The ProLogic L02-C is a digital lock system and therefore the lock must

also be programmed in digital mode. Both modes follow the same steps to reset / set which is done by

following the steps detailed below:

Step 1: Ensure the battery is connected to the Entry Pad.

Step 2: Ensure the lock cable is disconnected from the lock body.

Step 3: Locate the Reset Hole on the back of the lock (under the QC sticker).

Step 4: Using a paper clip depress the reset button, inside the reset hole, 3 times to dissipate

any latent energy in the lock.

Step 5: Now depress the reset button and hold.

Step 6: While continuing to depress the reset button, connect the lock cable to the lock body.

Step 7: Continue to hold down the reset button for 5 seconds and then release.

Step 8: Verify that the pairing has been completed, by opening the lock with the default code

111111.

Step 9: Press any button on the EntryPad to initiate a lock communication test. The EntryPad

will display the following information:

ProLogic L02-C Operation Instructions

Followed by:

Enter a valid code to test the lock.

The Default codes are as follows:

Super Code (ID00) is 111111

Manager Code (ID01) is 123456

Upon entry of a valid code, the lock will open. If the lock does not open and the LCD screen

displays the message “Fail to Link with Lock”, repeat the reset procedure. Be sure to hold down

the reset button through steps 5-7.

If you have difficulty resetting the lock, please call SecuRam Tech Support at (805) 988-8088 or email

info@securamsys.com.

1.3 Lock and EntryPad Installation

Included within your installation kit are (2) shoulder bolts and (3) lock mounting bolts.

Install the shoulder bolts on the safe door in the pre-drilled holes above and below the spindle

hole.

Now insert the lock cable (attached to the EntryPad) through the spindle hole.

On the backside of the safe door, you will see the lock mounting plate and the predrilled lock

mounting holes.

Connect the lock cable to the lock body and position the lock body appropriately on the lock

mounting plate.

Ensure that the lock cable is positioned so that it lies in the channel on the back of the lock. This

channel is provided to protect the lock cable from damage or crimping during installation.

Using the provided lock bolts, secure the lock body to the mounting plate.

Note: it is very important to ensure that there is an adequate gap between the lock bolt and the

boltwork. This gap must be 0.125”.

1.4.1 Installing the Battery –Standard Battery Compartment (located on the back of the EntryPad)

Connect the battery terminal clip to the 9V battery. (Duracell or Energizer brands are

recommended).

Position the battery so that the terminals are in the downward position and push the battery

into the battery compartment. See Fig. 1.

Carefully tuck the excess lock cable into the cavity on the back of the EntryPad and install the

EntryPad on the shoulder bolts. See Fig. 2.

ProLogic L02-C Operation Instructions

Be careful not to crimp or damage the lock cable upon EntryPad installation.

1.4.2 Installing the Battery –SureLock Battery Compartment (removable battery compartment)

Locate the SureLock Battery Compartment at the 5 o’clock position of the EntryPad. See Fig. 3.

Release the latch of the battery compartment, by pulling lever downward. See Fig 4.

Pull out the battery compartment from the bottom of the EntryPad. See Fig 5.

Install a new 9V alkaline battery (Duracell or Energizer brands are recommended) into the

compartment. The battery compartment will only receive the battery when the positive and

negative terminals are oriented correctly. See Fig. 6

Put the battery compartment back into the EntryPad. Push the latch of the battery

compartment up until it snaps closed. See Fig. 3

1.5 Testing the Lock Operation

The ProLogic L02-C comes with two factory default codes:

•Super Code (ID00) is 111111

•Manager Code (ID01) is 123456

Enter one of the valid codes to verify that the communication between the lock and EntryPad. The lock

will open.

ProLogic L02-C Operation Instructions

2.0 Lock Operation

Upon initial power up, the LCD screen starts a communications test as shown below:

Including Model Number

Software Version Number

No. of Users/ No. Users Programmed

Lock ID#/Host ID#

Model Name

After this initial power up it will also check to ensure that the system is communicating correctly. The

display will read “Link with Lock OK”.

If the Display reads: “Fail to Link with Lock” proceed to Section 1.2 entitled “Pairing the EntryPad and

the Lock”

2.1 Opening the Lock

The safe lock system has two default codes installed as follows:

•Super Code (ID00) 1-1-1-1-1-1

•Manager Code (ID01) 1-2-3-4-5-6

Step 1: Enter a valid code –for example ID00.

The display will read “ID00 Verified”.

And the Lock will open.

The display will read:

The lock will relock after 6 seconds.

Note: Time to relock is hard coded and cannot be changed.

2.2 Opening Lock with Time Delay Programmed

When Time Delay has been programmed, the user must enter a valid code.

Note: Users are defined as ID03- ID30

ID00

ProLogic L02-C Operation Instructions

Wait through the preprogrammed time delay period, then enter the code again to open the lock safe, as

follows:

Step1: Enter a valid code

Note: ID00, ID01 and ID02 are Administrator users and will bypass Time Delay.

Step 2: Display will read “Time Delay Start”

Step 3: Display will flash on every 15 seconds, counting up until it reaches the preprogrammed

time delay value.

Note: Administrators can override Time Delay to open lock anytime.

Step 4: When Time Delay expires, the EntryPad will beep twice then display: “Time Window

XX:00”, indicating the length of time the User has to enter a valid user code to gain entry.

The Counter will count down until the Time Window has expired. A user code is used to open

the lock.

Step 5: Enter a valid Code to open the lock.

2.3 Opening the Lock in Dual Control

The ProLogic L02-C can be programmed so that two User codes are required to open the lock. This

function is called “Enable Dual Mode”, See 8.1

To Open a Lock under Dual Control:

Step 1: Enter User code

The display will read “IDXX Verified”.

For example, ID03 will display “ID03 Verified”.

The display will then read:

“Enter 2nd User Code”

ProLogic L02-C Operation Instructions

For example, using ID04 for 2nd code will read “ID04 Verified”.

The lock will open and relock in 6 seconds.

2.4 Opening the Lock with a Multi-Lock System

The ProLogic L02-C can operate up to 4 locks.

To Open a Lock with a Multi-Lock System:

Step 1: Enter a valid code

The display will read “IDXX Verified”.

Step 2: The system will now prompt you to enter the number of the Lock to open

3.0 Code Management

The ProLogic L02-C comes with two default codes:

•Super Code (ID00) is 111111

•Manager Code (ID01) is 123456

It is strongly recommended that both these default codes are changed before the lock system is put into

service.

The ProLogic L02-C has the capability to add up to 29 codes, in addition to the default codes.

ID02 is a Manager Code and therefore has management functionality (the same as ID01).

ID03-30 are User Codes.

3.1 Code Length Options

The ProLogic L02-C allows you the ability to manage the code length for all safe lock operators. This

requirement meets the UL specification for 1 million available unique codes. Setting the code length is a

global setting and applies to all safe lock operators –ID00 to ID30.

There are 3 options available as follows:

Code Length 6 digits –10 total codes available - This is the default mode and meets the UL

requirement.

Code Length 8 digits –30 total codes available –This mode also meets the UL requirement.

Code Length 6 digits –30 total codes available –This mode does not meet the UL requirement.

ProLogic L02-C Operation Instructions

3.1.1 PW L –6; Users –10 –This is the default mode.

NOTE: This operation must be performed with the safe door open and with access to the back of the

lock, as a mechanical reset must be performed during this programming sequence.

Step1: Press the Menu/OK button.

Step 2: Using the and , scroll to the System Menu and Press Menu/OK.

Step 3: The display will prompt you to enter a valid code. Enter the Super Code (ID00) only .

This function is not available to Manager Codes ID01 or ID02. The “Select Menu” message will

be displayed as follows:

Step 4: Scroll and to the menu selection “PW L –6; Users –10” and Press OK

Step 5: The LCD will display a warning followed by “Delete All Users?”, press OK to confirm.

All users have been deleted.

IMPORTANT: The LCD will advise if a reset is required to finalize the programming. If required, follow

the Mechanical Reset procedure outlined in 9.4 Mechanical Reset.

The code length will now be 6 digits and the total available users will be 10.

The Super Code ID00 will now be 1-1-1-1-1-1

The Manager Code ID01 will now be 1-2-3-4-5-6

3.1.2 PW L –8; Users –30

NOTE: This operation must be performed with the safe door open and with access to the back of the

lock, as a mechanical reset must be performed during this programming sequence.

ProLogic L02-C Operation Instructions

Step1: Press the Menu/OK button.

Step 2: Using the and , scroll to the System Menu and Press Menu/OK.

Step 3: The display will prompt you to enter a valid code. Enter the Super Code (ID00) only .

This function is not available to Manager Codes ID01 or ID02. The “Select Menu” message will

be displayed as follows:

Step 4: Scroll and to the menu selection “PW L –8; Users –30” and Press OK

Step 5: The LCD will display a warning followed by “Delete All Users?”, press OK to confirm.

All users have been deleted.

IMPORTANT: The LCD will advise if a reset is required to finalize the programming. If required, follow

the Mechanical Reset procedure outlined in 9.4 Mechanical Reset.

The code length will now be 6 digits and the total available users will be 30.

The Super Code ID00 will now be 1-1-1-1-1-1-0-0

The Manager Code ID01 will now be 1-2-3-4-5-6-0-0

3.1.3 PW L –6; Users –30

NOTE: This operation must be performed with the safe door open and with access to the back of the

lock, as a mechanical reset must be performed during this programming sequence.

Step1: Press the Menu/OK button.

Step 2: Using the and , scroll to the System Menu and Press Menu/OK.

ProLogic L02-C Operation Instructions

Step 3: The display will prompt you to enter a valid code. Enter the Super Code (ID00) only .

This function is not available to Manager Codes ID01 or ID02. The “Select Menu” message will

be displayed as follows:

Step 4: Scroll and to the menu selection “PW L –6; Users –30” and Press OK

Step 5: The LCD will display a message to indicate that this setting does not meet the UL

requirement.

Step 6: The LCD will then display a warning followed by “Delete All Users?”, press OK to

confirm.

All users have been deleted.

IMPORTANT: The LCD will advise if a reset is required to finalize the programming. If required, follow

the Mechanical Reset procedure outlined in 9.4 Mechanical Reset.

The code length will now be 8 digits and the total available users will be 30.

The Super Code ID00 will now be 1-1-1-1-1-1

The Manager Code ID01 will now be 1-2-3-4-5-6

3.2 Enrolling New Users

Step1: Press the Menu/OK button.

Andere Securam Sperren Handbücher

Securam

Securam ScanLogic B22 Bedienungsanleitung

Securam

Securam MANAGER Series Bedienungsanleitung

Securam

Securam ProLogic B01 Bedienungsanleitung

Securam

Securam V8 Technisches Handbuch

Securam

Securam SH-WB01 Bedienungsanleitung

Securam

Securam FPC-0601A-D22 Bedienungsanleitung

Securam

Securam SafeLogic Basic Series Bedienungsanleitung

Securam

Securam ScanLogic D66 Bedienungsanleitung

Securam

Securam ScanLogic Optical Installationshandbuch

Securam

Securam ProLogic B22 Bedienungsanleitung

Securam

Securam SafeLogic TopLit Series Bedienungsanleitung

Securam

Securam SafeLogic C10 D-Drive Bedienungsanleitung

Securam

Securam ProLogic L66 Bedienungsanleitung

Securam

Securam ProLogic L22 Bedienungsanleitung

Securam

Securam SafeLogic Basic Bedienungsanleitung

Securam

Securam SafeLogic Basic Bedienungsanleitung

Securam

Securam ProLogic L01 Bedienungsanleitung

Securam

Securam D Series Bedienungsanleitung

Securam

Securam SafeLogic Xtreme Betriebsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Securam

Securam ProLogic L22 Bedienungsanleitung

Securam

Securam SH-TB01 Bedienungsanleitung

Securam

Securam SafeLogic Basic Bedienungsanleitung

Securam

Securam EM-1701A-R Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung

Metra Electronics

Metra Electronics Door Access Terminal Combo Bedienungsanleitung