Securam ProLogic L22 Bedienungsanleitung

ProLogic L22 Operation Instructions

Document No: EC-0601A-L22-130919

Version No: V1.01

1.0 System Installation

1.1 System Components

1.2 Pairing the EntryPad with the Lock(s)

1.3 Lock and EntryPad Installation

1.4 Installing Battery

1.5 Test Lock Operation

2.0 Lock Operation

2.1 Opening the Lock

2.2 Opening the Lock in Time Delay

2.3 Opening the Lock Under Duress

2.4 Opening the Lock in Dual Control

2.5 Opening the Lock with a Multi-Lock System

3.0 Set Date and Time

3.1 Set Clock Time

3.2 Show Clock Time

3.3 DayLight Savings Time

4.0 Code Management

4.1 Enrolling New users

4.2 Change Code

4.3 Delete One User

4.4 Delete All Users

4.5 Disable/Enable User

5.0 System Identification

5.1 System Info

6.0 Time Delay

6.1 Set/Cancel Time Delay

6.2 Set Duress Time Delay

6.3 Setting Time Delay Override Users

7.0 Audit Trail Functionality

7.1 Show Audit Trail

7.2 Uploading Audit Trail

8.0 Single or Dual Control

8.1 Enable Dual Mode

9.0 Door Management

9.1 Max. Door Open Time

9.2 Configuring a Multi-lock system

9.3 Set Number of Locks

9.4 Authorize Locks

9.5 Enable Sequence

10.0 Duress Management

10.1 Duress Setup and Wiring Configuration

10.2 Duress Code Shift

11.0 Device Management

11.1 Set Device ID

12.0 Data Management

12.1 Encryption Key Set

13.0 Recovering the System – Reset to Default

13.1 Recovery Code Set

13.2 Recover System

13.3 Simple Mechanical Reset

14.0 System Testing

14.1 Cycle Testing

14.2 Hardware Testing

15.0 Menus

15.1 The ProLogic L22 Menus

ProLogic L22 Operation Instructions

1.0 System Installation

1.1 System Components

The system consists of (1) EntryPad – Part # EC-0601A-L22 plus (1) or more Lock bodies as follows:

 SwingBolt – Part # EL-0601

 SwingBolt with Status – Part # EL-0601-S

 DeadBolt – Part # EL-0701

 SpringBolt – Part #EL-0801

 StrikeBolt – Part #EL-0901

Note: The ProLogic L22 can control up to 4 locks when used in conjunction with the Expansion Box –

Part # CB11-1T4. (If setting up a multi-lock system, please refer to Section 10.2 – Multi-Lock Systems)

1.2 Pairing the EntryPad and the Lock

SECURAM safe lock systems can operate in two different modes depending upon the type of EntryPad

being used with the lock body. The ProLogic L22 is a digital lock system and therefore the lock must also

be programmed in digital mode. Both modes follow the same steps to reset / set which is done by

following the steps detailed below:

Step 1: Ensure the battery is disconnected from the Entry Pad.

Step 2: Ensure the lock cable is disconnected from the lock body.

Step 3: Locate the Reset Hole on the back of the lock (under the QC sticker).

Step 4: Using a paper clip depress the reset button, inside the reset hole, 3 times to dissipate

any latent energy in the lock.

Step 5: Now depress the reset button and hold.

Step 6: While continuing to depress the reset button, connect the lock cable to the lock body.

Step 7: While continuing to depress the reset button, connect the 9V battery to the EntryPad

terminals.

Step 8: Continue to hold down the reset button for 5 seconds and then release.

Step 9: Verify that the pairing has been completed, by opening the lock with the default code

111111.

Step 10: Press any button on the EntryPad to initiate a lock communication test. The EntryPad

will display system information followed by:

ProLogic L22 Operation Instructions

Enter a valid code to test the lock.

The Default codes are as follows:

 Super Code (ID00) is 111111

 Manager Code (ID01) is 123456

Upon entry of a valid code, the lock will open. If the lock does not open and the LCD screen

displays the message “Fail to Link with Lock”, repeat the reset procedure. Be sure to hold down

the reset button through steps 5-8.

If you have difficulty resetting the lock, please call SECURAM Tech Support at (805) 988-8088 or email

[email protected].

1.3 Lock and EntryPad Installation

Included within your installation kit are (2) shoulder bolts and (3) lock mounting bolts.

 Install the shoulder bolts on the safe door in the pre-drilled holes above and below the spindle

hole.

 Now insert the lock cable (attached to the EntryPad) through the spindle hole.

 On the backside of the safe door, you will see the lock mounting plate and the predrilled lock

mounting holes.

 Connect the lock cable to the lock body and position the lock body appropriately on the lock

mounting plate.

 Ensure that the lock cable is positioned so that it lies in the channel on the back of the lock. This

channel is provided to protect the lock cable from damage or crimping during installation.

 Using the provided lock bolts, secure the lock body to the mounting plate.

Note: it is very important to ensure that there is an adequate gap between the lock bolt and the

boltwork. This gap must be 0.125”.

1.4 Installing the Battery

 Connect the battery terminal clip to the 9V battery. (It is required to use standard alkaline

batteries; Duracell or Energizer batteries are preferred.)

 Position the battery so that the terminals are in the downward position and push the battery

into the battery compartment.

 Carefully tuck the excess lock cable into the cavity on the back of the EntryPad and install the

EntryPad on the shoulder bolts.

ProLogic L22 Operation Instructions

 Be careful not to crimp or damage the lock cable upon EntryPad installation.

1.5 Testing the Lock Operation

The ProLogic L22 comes with two factory default codes:

• Super Code (ID00) is 111111

• Manager Code (ID01) is 123456

Enter one of the valid codes to verify that the communication between the lock and EntryPad. The lock

will open.

2.0 Lock Operation

Upon initial power up, the LCD screen starts a communications test as shown below:

 Including Model Number

 Software Version Number

 No. of Users/ No. Users Programmed

 Lock ID#/Host ID#

 Model Name

 No. of Audit Events

After this initial power up it will also check to ensure that the system is communicating correctly. The

display will read “Link with Lock OK”.

If the Display reads: “Fail to Link with Lock” proceed to Section 1.2 entitled “Pairing the Entrypad and

the Lock”

2.1 Opening the Lock

The safe lock system has two default codes installed as follows:

• Super Code (ID00) 1-1-1-1-1-1

• Manager Code (ID01) 1-2-3-4-5-6

Step 1: Enter a valid code – for example ID00.

The display will read “ID00 Verified”.

And the Lock will open.

ProLogic L22 Operation Instructions

The display will read:

The lock will relock after 6 seconds.

Note: Time to relock is hard coded and cannot be changed.

2.2 Opening Lock with Time Delay Programmed

When Time Delay has been programmed, the user must enter a valid code.

Note: Users are defined as ID03- ID30

Wait through the preprogrammed time delay period, then enter the code again to open the lock safe, as

follows:

Step1: Enter a valid code

Note: ID00, ID01 and ID02 are Administrator users and will bypass Time Delay.

Step 2: Display will read “Time Delay Start”

Step 3: Display will flash on every 15 seconds, counting up until it reaches the preprogrammed

time delay value.

Note: Administrators can override Time Delay to open lock anytime.

Step 4: When Time Delay expires, the entrypad will beep twice then display: “Time Window

XX:00”, indicating the length of time the User has to enter a valid user code to gain entry.

The Counter will count down until the Time Window has expired. A user code is used to open

the lock.

Step 5: Enter a valid Code to open the lock.

2.3 Opening the Lock Under Duress

ID00

ProLogic L22 Operation Instructions

The ProLogic L22 has a Duress Feature, which allows a User or Admin to open the lock and send a silent

Duress signal indicating that you are in danger. By default, the duress function is active and cannot be

disabled.

In Order to send a signal, the system must have a CB10 junction box installed and must be connected to

an alarm panel.

To Open the Lock under Duress:

Step 1: Enter a valid Code, but add or subtract 1 from the code. The Lock will open as normal and a

silent alarm will be issued.

Note: This will be logged as “Duress Unlock” in events.

For example, if your code is 123456; under Duress, enter 123455 or 123457 to send silent alarm.

Note: The ProLogic L22 has a function called “Duress Code Shift”. This function allows you to specify

the number to be added or subtracted from the code during a duress entry. See Section C - 11.0.

2.4 Opening the Lock in Dual Control

The ProLogic L22 can be programmed so that two User codes are required to open the lock. This

function is called “Enable Dual Mode”, See 8.1

To Open a Lock under Dual Control:

Step 1: Enter User code

The display will read “IDXX Verified”.

For example, ID03 will display “ID03 Verified”.

The display will then read:

“Enter 2nd User Code”

For example, using ID04 for 2nd code will read “ID04 Verified”.

The lock will open and relock in 6 seconds.

ProLogic L22 Operation Instructions

2.5 Opening the Lock with a Multi-Lock System

The ProLogic L22 can operate up to 4 locks.

To Open a Lock with a Multi-Lock System:

Step 1: Enter a valid code

The display will read “IDXX Verified”.

Step 2: The system will now prompt you to enter the number of the Lock to open

3.0 Set Date and Time

The ProLogic L22 is an audit lock and it tracks events based on user, activity, date, and time. In order to

set the system date and time complete the following process.

3.1 Set Clock Time

Step1: Press the Menu/OK button

Step 2: Using the  and, scroll to the System Menu and press OK.

Step 3: The display will prompt you to enter a valid code. Enter either the Super Code (ID00) or

the Manager Code (ID01). The “Select Menu” message will be displayed as follows:

Step 4: Scroll  to the menu selection “Set Clock Time” and Press OK

Step 5: Press OK

Step 6: Each of the elements of the date and time will flash when it is available to be set. Use the

 and  to scroll to the correct value and Press OK to move to the next element.

3.2 Show Clock Time

Step1: Press the Menu/OK button

Step 2: Using the  and, scroll to the System Menu and press OK.

ProLogic L22 Operation Instructions

Step 3: The display will prompt you to enter a valid code. Enter either the Super Code (ID00) or

the Manager Code (ID01). The “Select Menu” message will be displayed as follows:

Step 4: Scroll  to the menu selection “Show Clock Time” and Press OK

Step 5: The LCD will display the current system date and time, as follows:

3.3 DayLight Savings Time

The ProLogic L22 can be set to manage Daylight Savings Time and automatically updating preset date

and time. Using this menu selection, you can turn on Daylight Savings Time management or turn it off.

**Note: The example below shows that Daylight Savings Time will start in March (3rd month), 2nd full

week at 2:00 am on the first day of the week (Sunday). And Day Light Savings Time will end in

November (11th month), 1st full week at 2:00 am on the first day of the week (Sunday).

Step1: Press the Menu/OK button

Step 2: Using the  and , scroll to the System Menu and press Menu/OK

Step 3: The display will prompt you to enter a valid code. Enter either the Super Code (ID00) or

the Manager Code (ID01). The “Select Menu” message will be displayed as follows:

Step 4: Scroll  to the menu selection “Daylight Savings TM” and Press OK

Step 5: Press the  button to turn Daylight Savings Time Management on. (To turn it off, press

the  button)

ProLogic L22 Operation Instructions

Step 6: (Starting Month) The system will now request the month in which Daylight Savings Time

is to begin. The default is North American DST Month 3 – March. To change press the  and 

to set the Month; and press OK

Step 7: (Starting Week) The system will now request the week of the month in which Daylight

Savings Time is to begin. The default is North American DST Week 2 – note – the system

calculates this as the 2nd full week in this month. To change Press the  and  to set the Week;

and press OK

Step 8: (Starting Time) The system will now request the Time on the first day of the week

(Sunday) at which Daylight Savings Time is to begin. The default is North American DST Time 2 –

2:00am. To change Press the  and  to set the Time; and press OK

Step 9: (Ending Month) The system will now request the month in which Daylight Savings Time

is to end. The default is North American DST Month 11 – November. To change press the  and

 to set the Month; and press OK

Step 10: (Ending Week) The system will now request the Week in which Daylight Savings Time

is to end. The default is North American DST Week 1 – note – the system calculates this as the

1st full week in this month. To change Press the  and  to set the Week; and press OK

Step 11: (Ending Time) The system will now request the Time on the first day of the week

(Sunday) at which Daylight Savings Time is to end. The default is North American DST Time 2 –

2:00am. To change Press the  and to set the Week; and press OK

ProLogic L22 Operation Instructions

Therefore to set to the North American DST, just select “Y” on the first display screen and then accept

the defaults for all other settings by pressing OK.

4.0 Code Management

The ProLogic L22 comes with two default codes:

• Super Code (ID00) is 111111

• Manager Code (ID01) is 123456

It is strongly recommended that both these default codes are changed before the lock system is put into

service.

4.1 Enrolling New Users

Step1: Press the Menu/OK button.

Step 2: Using the  and , scroll to the System Menu and Press Menu/OK

Step 3: The display will prompt you to enter a valid Administrator code

 Enter either the Super Code (ID00) or the Manager Code (ID01). The “Select Menu”

message will be displayed as follows:

Step 4: Scroll  to the menu selection “Enroll New User” and Press OK

Step 5: The next available ID position is displayed. To select this ID, Press OK; or to select a

different ID position, Press  to desired ID and press OK

Step 6: Now enter a 6 digit code

Step 7: Repeat new code

Step 8: System will verify that code has been saved.

Andere Handbücher für ProLogic L22

Dieses Handbuch passt für folgende Modelle

Andere Securam Sperren Handbücher

Securam

Securam SH-WB01 Bedienungsanleitung

Securam

Securam EM-1701A-R Bedienungsanleitung

Securam

Securam MANAGER Series Bedienungsanleitung

Securam

Securam SH-TB01 Bedienungsanleitung

Securam

Securam ProLogic L02-C Bedienungsanleitung

Securam

Securam SafeLogic Xtreme Bedienungsanleitung

Securam

Securam ProLogic L66 Bedienungsanleitung

Securam

Securam D Series Bedienungsanleitung

Securam

Securam SafeLogic Basic Series Bedienungsanleitung

Securam

Securam SafeLogic Xtreme Betriebsanleitung

Securam

Securam SafeLogic C10 D-Drive Bedienungsanleitung

Securam

Securam ProLogic B22 Bedienungsanleitung

Securam

Securam ProLogic B01 Bedienungsanleitung

Securam

Securam ScanLogic B22 Bedienungsanleitung

Securam

Securam FPC-0601A-D22 Bedienungsanleitung

Securam

Securam ScanLogic D66 Bedienungsanleitung

Securam

Securam ProLogic L22 Bedienungsanleitung

Securam

Securam V8 Technisches Handbuch

Securam

Securam SCANLOGIC FPC-1808-II-MB Bedienungsanleitung

Securam

Securam ProLogic L01 Bedienungsanleitung

Securam

Securam ScanLogic Optical Installationshandbuch

Securam

Securam SafeLogic Basic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Securam

Securam SafeLogic TopLit Series Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung

Metra Electronics

Metra Electronics Door Access Terminal Combo Bedienungsanleitung