Securam SafeLogic C10 D-Drive Bedienungsanleitung

Important:

• For indoor use only.

• Battery Low Voltage: The entrypad will alert low battery when battery voltage is

low. PLEASE REPLACE THE BATTERY IMMEDIATELY.

FEATURES:

1. Manager Code (ID 01):

a) Open lock.

b) Change code.

c) Add/delete user.

d) Disable/Enable user.

e) Manufacturer default is 1-2-3-4-5-6.

2. 8 User Codes (ID 02 to ID 09):

a) Open lock.

b) Change code.

c) No Manufacturer default user codes.

3. Wrong Entry Penalty (Penalty Time)

Entry of four (4) consecutive invalid codes results in a 5-minute penalty time period.

a) The unit beeps at 5 second intervals indicating that it is still in the penalty time

period.

b) While the system is in penalty time, the EntryPad buttons remain unresponsive.

c) While the system is in penalty time, removal of the batteries will interrupt the

penalty time countdown. Upon reinstallation of the batteries, the EntryPad

continues to count down until the 5 minute penalty time period expires.

4. Standby Status

In order to conserve battery power, The system will revert to standby status if there is

Doc.No.: EM1701AC10210303

Version No.: V1.01

SafeLogic C10 D-Drive - Operating Instructions

This manual is for the SafeLogic C10 D-Drive EM-1701A-C10 EntryPad used in conjunction with DL-

1701 D-Drive DeadBolt Lock Body.

In some instances the Manager Code and associated Operating Instructions are not issued

to the End User. In this case, simply remove this insert from the Operating Instruction.

no key press in 10 seconds. Standby status is indicated by two short beeps.

5. Automatic Re-lock

The safe lock system automatically relocks after 6 seconds of being opened by a

valid code.

6. Low Battery Alert

a) Repeated beeping (8 beeps) during an unlock operation indicates that the battery

is low and needs immediate replacement.

b) Manufacturer recommends the use of 9-Volt standard alkaline batteries (Duracell

or Energizer brands are recommend) replaced annually.

USER PROGRAMMING INSTRUCTIONS

1. ALWAYS PERFORM OPERATIONS WITH THE SAFE LOCK SYSTEM UNLOCK

AND THE SAFE DOOR OPEN.

2. Before closing the door, make sure all of the program changes are correct.

3. The system will not allow the User Code to be set to six zeros or six nines.

1. To Change Code

a) Enter “0” six times. One beep will sound, indicating that the entry is valid and the

system is awaiting the code change.

b) Next, enter the existing six (6) digit code one time. One beep will sound, which

indicates that the entry is valid.

c) Enter a new six (6) digit code one time. Two beeps will sound, indicating the entry

is valid.

d) Re-enter the new six (6) digit code. One beep will sound, indicating the codes

entered in steps c and d are the same and the code changing process is

successful.

e) If Three beeps sound, the code change process has been unsuccessful. The

existing code is still valid. Repeat steps a to d.

Note:

a) User Code can’t be 000000 or 999999.

b) Verify the new code at least 3 times before closing the door to make sure the

code has been programmed correctly.

c) The system will revert to standby status if there is no key press within 10

seconds. Standby status is indicated by two short beeps.

2. Add User (ID 02 to ID 09)

a) Enter the manager code and hold down last digit until one beep sounds,

followed by two beeps.

b) Push “1”. One beep sounds.

c) Enter the ID of the user to be added. For example, enter 2 to add user ID 2. One

beep sounds.

d) Enter a desired six (6) digit code once. One beep sounds.

e) Re-enter the six (6) digit code. One beep sounds, indicating the codes entered

in steps c and d are the same and the user code has been added successfully.

f) If two beeps sound, the process failed. Repeat steps a to d.

Note:

a) User Code can’t be 000000 or 999999.

b) Verify the new code at least 3 times before closing the door to make sure the

code has been programmed correctly.

c) The system will revert to standby status if there is no key press within 10

seconds. Standby status is indicated by two short beeps.

3. Delete User (ID 02 to ID 09)

a) Enter the manager code and hold down last digit until one beep sounds, followed

by two beeps.

b) Push “3”. One beep sounds.

c) Enter the ID of the user to be deleted. For example, enter 2 to delete user ID 2.

One beep sounds.

d) Enter the deleted user code to make sure the code is deleted.

4. Disable User (ID 02 to ID 09)

a) Enter the manager code and hold down last digit until one beep sounds, followed

by two beeps.

b) Push “2”. One beep sounds.

c) Enter the ID of the user to be disabled. For example, enter 2 to disable user ID 2.

One beep sounds.

d) Enter the disabled user code to make sure the code is disabled.

5. Enable User (ID 02 to ID 09)

a) Enter the manager code and hold down last digit until one beep sounds, followed

by two beeps.

b) Push “1”. One beep sounds.

c) Enter the ID of the disabled user to be enabled. For example, enter 2 to enable

user ID 2. One beep sounds.

Note:

a) Verify the enabled code at least 3 times before closing the door to make sure the

code has been programmed correctly.

b) The system will revert to standby status if there is no key press within 10

seconds. Standby status is indicated by two short beeps.

6. Open lock with Time Delay

• Super Code programs Time Delay.

a) Enter the user code

b) One beep sounds but lock doesn’t unlock.

c) One beep sounds every ten (10) seconds.

d) Four beeps sound at the end of Time Delay period indicating Time Window

starts.

e) Two beeps sound every ten (10) seconds during Time Window period.

f) Enter code again within Time Window to unlock.

7. Open lock with Dual User Mode

• Super Code programs Dual User or Single User Mode.

a) Enter User code. One beep sounds but lock doesn’t unlock.

b) Enter Manager code to open.

8. Open lock with Dual User Mode with Time Delay

• Super Code programs Dual User or Single User Mode.

• Super Code programs Time Delay.

a) Enter User code. One beep sounds but lock doesn’t unlock.

b) One beep sounds every ten (10) seconds.

c) Four beeps sound at the end of Time Delay period indicating Time Window

starts.

d) Two beeps sound every ten (10) seconds during Time Window period.

e) Enter User code and Manager code within Time Window to unlock.

Specifications

：

Power Supply: DC 9V

Power Supply Range: DC 4.5V-12V

Standby Current : <50μA

Active Current: <20mA

Battery Low Voltage: 5.2±0.2V

Working Temperature: 0℃~ +49℃

Working Humidity (max): <90%

Code Length: 6 Digits

Mechanical System Life Span: >100,000 Cycles

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Securam Sperren Handbücher

Securam

Securam ProLogic L66 Bedienungsanleitung

Securam

Securam ProLogic B22 Bedienungsanleitung

Securam

Securam ProLogic B01 Bedienungsanleitung

Securam

Securam D Series Bedienungsanleitung

Securam

Securam SafeLogic Basic Bedienungsanleitung

Securam

Securam SafeLogic Basic Bedienungsanleitung

Securam

Securam EM-1701A-R Bedienungsanleitung

Securam

Securam FPC-0601A-D22 Bedienungsanleitung

Securam

Securam SH-WB01 Bedienungsanleitung

Securam

Securam ProLogic L22 Bedienungsanleitung

Securam

Securam ScanLogic B22 Bedienungsanleitung

Securam

Securam MANAGER Series Bedienungsanleitung

Securam

Securam SafeLogic Xtreme Bedienungsanleitung

Securam

Securam SafeLogic Basic Bedienungsanleitung

Securam

Securam SH-TB01 Bedienungsanleitung

Securam

Securam SafeLogic Basic Series Bedienungsanleitung

Securam

Securam SCANLOGIC FPC-1808-II-MB Bedienungsanleitung

Securam

Securam ScanLogic D66 Bedienungsanleitung

Securam

Securam ScanLogic Optical Installationshandbuch

Securam

Securam ProLogic L01 Bedienungsanleitung

Securam

Securam SafeLogic Xtreme Betriebsanleitung

Securam

Securam ProLogic L02-C Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Securam

Securam ProLogic L22 Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung

Metra Electronics

Metra Electronics Door Access Terminal Combo Bedienungsanleitung