Siemens RUGGEDCOM WIN7000 Bedienungsanleitung

RUGGEDCOM WIN7000

Installation Guide

9/2014

FCC Statement and

Cautions

Introduction 1

Site and Installation

Requirements 2

Installation Procedures 3

Setup 4

Troubleshooting 5

Connector and Cable

Pinouts A

WIN7000 Specifications B

List of Acronyms C

Warranty D

RC1062-EN-02

RUGGEDCOM WIN7000

Installation Guide

RUGGEDCOM WIN7000

Installation Guide

Table of Contents

iii

Table of Contents

FCC Statement and Cautions ............................................................................. v

Chapter 1

Introduction .......................................................................................................... 1

1.1 About this Guide .......................................................................................................................... 1

1.2 Capabilities and Features ............................................................................................................. 1

1.3 Safety Information ........................................................................................................................ 2

1.3.1 General ............................................................................................................................. 2

1.3.2 Power Supply Requirements .............................................................................................. 2

1.3.3 Equipment Installation ........................................................................................................ 4

1.3.4 Radio Frequency (RF) Exposure ........................................................................................ 4

1.3.5 Lightning Protection ........................................................................................................... 4

1.3.6 Power Cord Protection ....................................................................................................... 4

1.3.7 Servicing ........................................................................................................................... 4

1.3.8 Antenna Grounding Requirements ...................................................................................... 5

1.3.9 Outdoor Grounding System ................................................................................................ 5

1.3.10 User Ports and Power Supply .......................................................................................... 5

1.3.11 Safety Hazards ................................................................................................................ 5

1.4 WIN7000 Physical Specifications .................................................................................................. 6

Chapter 2

Site and Installation Requirements ..................................................................... 7

2.1 Mounting Considerations .............................................................................................................. 7

Chapter 3

Installation Procedures ........................................................................................ 9

3.1 Pre-Installation Safety Instructions ................................................................................................ 9

3.2 Package Components and Unpacking ........................................................................................... 9

3.3 Installation Tools .......................................................................................................................... 9

3.4 Installing the Base Station .......................................................................................................... 10

3.4.1 Sealing Screw ................................................................................................................. 10

3.4.2 WIN7000 Mounting Bracket .............................................................................................. 11

3.4.3 Pole Mounting ................................................................................................................. 12

3.4.4 Wall Mounting ................................................................................................................. 13

3.4.5 Tower Mount ................................................................................................................... 14

Table of Contents

RUGGEDCOM WIN7000

Installation Guide

3.4.6 Power and Cable Connections ......................................................................................... 15

3.4.6.1 PEC (Copper) Type Base Station .......................................................................... 15

3.4.6.2 SFA (Optical) Type Base Station ............................................................................ 17

3.4.6.3 SFD Type Base Station ......................................................................................... 18

3.4.7 Grounding the Device ...................................................................................................... 21

3.4.8 Installing the GPS Antenna .............................................................................................. 21

3.4.9 2.3GHz Band Cavity Filters Installation ............................................................................. 22

3.5 Weatherproofing ......................................................................................................................... 30

3.5.1 Weatherproofing Cable Connections ................................................................................. 31

3.6 Hazardous Location Information .................................................................................................. 34

3.7 Hazardous Location Installation ................................................................................................... 34

Chapter 4

Setup .................................................................................................................. 37

4.1 Connecting to the WIN7000 Web Interface .................................................................................. 37

Chapter 5

Troubleshooting .................................................................................................. 41

5.1 No IP connectivity ...................................................................................................................... 41

5.2 No Serial Connection ................................................................................................................. 41

Appendix A

Connector and Cable Pinouts ............................................................................ 43

A.1 Power and Ethernet Cable Pinouts ............................................................................................. 43

A.2 Console Cable Pinouts ............................................................................................................... 44

Appendix B

WIN7000 Specifications ..................................................................................... 45

Appendix C

List of Acronyms ................................................................................................ 47

Appendix D

Warranty ............................................................................................................. 49

RUGGEDCOM WIN7000

Installation Guide

FCC Statement and Cautions

Federal Communications Commission Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the interference at his own expense.

CAUTION!

Caution: Service

This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall

render all warranties null and void.

Changes or modifications not expressly approved by SIEMENS could invalidate specifications,

test results, and agency approvals, and void the user’s authority to operate the equipment.

CAUTION!

Caution: Physical Access

This product should be installed in a restricted access location where access can only be gained by

service personnel or users who have been instructed about the reasons for the restrictions applied to

the location and about any precautions that shall be taken; and access is through the use of a tool or

lock and key, or other means of security, and is controlled by the authority responsible for the location.

RUGGEDCOM WIN7000

Installation Guide

FCC Statement and Cautions

RUGGEDCOM WIN7000

Installation Guide

Chapter 1

Introduction

About this Guide 1

Introduction

The WIN7000 High Power Base Station is a member of the RUGGEDCOM WIN family, a line of mobile WiMAX

broadband wireless access systems based on the 802.16e mobile WiMAX standard. RUGGEDCOM systems are

designed for robustness and simplicity, offering feature-rich services with low deployment and operation costs.

The WIN7000 is a member of a line of mobile WiMAX broadband wireless access systems based on the 802.16e

mobile WiMAX standard. These systems are designed for robustness and simplicity, offering feature-rich services

with low deployment and operation costs.

The WIN7000 is a cost-effective solution for wireless access services, designed for point-to-multipoint broadband

wireless access applications in varying conditions and locations. It is a one-sector base station.

The base station communicates with fixed and mobile subscriber units, according to defined service criteria and

customer service level agreements. The WIN7000 also connects to the service provider backbone, supporting

end-to-end Quality of Service (QoS) requirements.

The system uses OFDMA radio technology, providing robustness in adverse channel conditions and enabling

Non-Line-Of-Sight (NLOS) operation. This improves coverage and maintains a high level of spectral efficiency.

Modulation and coding are continuously adapted to prevailing link conditions, ensuring an optimal balance

between robustness and efficiency. The use of STC/MRC and MIMO radio technologies optimizes link

performance, ensuring enhanced bandwidth and service coverage.

The RUGGEDCOM WIN7000 is a full outdoor base station, designed for easy installation and mounting on poles,

street lamps, towers, or walls. The WIN7000 can be equipped with copper or fibre network interfaces for flexible

integration into the operator’s backbone.

The WIN7000 is supported by RUGGEDCOM NMS, Siemens’s comprehensive Network Management System.

Section 1.1

About this Guide

This installation guides describes the installation of the WIN7000 High Power Base Station.

This guide is intended for use by base station installers and operators, and assumes readers have a working

knowledge of WiMAX technologies and procedures. While some safety precautions are reviewed here, it

is assumed that installers are trained in safe installation practices. Users unfamiliar with safe installation

procedures, WiMAX technologies, and service procedures should not rely on this manual for comprehensive

guidance.

Section 1.2

Capabilities and Features

The WIN7000 provides the full base station functionality necessary for serving a single sector:

• Supported Frequency Bands: 5251, 5151, 7251

• All-outdoor, single-box installation

• IEEE802.16e Wave2 Standard Compliance

Chapter 1

Introduction

RUGGEDCOM WIN7000

Installation Guide

2 Safety Information

• Backbone Ethernet connectivity via a 10/100 Base-T network interface

• Fixed and mobile CPE support

• 3.5 MHz, 5MHz, 7MHz and 10MHz channel bandwidth support

• MIMO (2×2) support

• Various Radio Frequency (RF) options, including 1.x, 2.x and 3.x GHz band support

• Traffic classification and connection establishment initiation

• Quality of Service (QoS) management

• Alarm management

• Internal SNMP agent, enabling extensive In-Band (IB) management of the base station and its registered CPEs

• R6 interface to ASN-GW profile C

• Power requirement: 48VDC

Section 1.3

Safety Information

Section 1.3.1

General

• Read this user manual and follow all operating and safety instructions.

• The base station and antenna must be installed by a professional installer.

• Do not exceed the described limits.

Section 1.3.2

Power Supply Requirements

• The power supply unit should be a Class 2 power supply, safety-certified according to national codes.

• Maximum output current should not exceed 5A.

• Maximum output voltage of the power supply should not exceed 60VDC.

• Minimum output voltage should not be below 42VDC.

• The disconnecting device is defined as the following:

▪ When connected to an AC/DC power supply, the appliance coupler of the AC/DC power supply is regarded

as the main disconnecting device for the base station.

▪ When connected to a DC battery power supply, a double pole circuit breaker, rated 10A 60VDC, is regarded

as the main disconnecting device for the base station.

The unit is considered to be connected to a centralized DC power system, therefore the power line should be

grounded. The unit should be permanently connected to ground with 16AWG cable or less. See the figures below

for two methods of power grounding (from the UL 60950-1 standard; according to UL 60950-22). When the unit is

connected to a centralized DC Power System, the "+" side of the supply should be grounded, as per UL60950-1

and UL 60950-22 requirements.

RUGGEDCOM WIN7000

Installation Guide

Chapter 1

Introduction

Power Supply Requirements 3

Figure 1: Typical Centralized DC Power System, Plant and Distribution Source-Grounded DC Power System

Figure 2: Typical Centralized DC Power System, Plant and Distribution DC Power System Grounded at Equipment

Location

Chapter 1

Introduction

RUGGEDCOM WIN7000

Installation Guide

4 Equipment Installation

Section 1.3.3

Equipment Installation

Install the equipment in accordance with the electrical code relevant to the country of installation, such as the

National Electrical Code (NEC), ANSI/NFPA 70; the Canadian Electrical Code (CEC), Part 1, CSA C22.1;

and when applicable, the National Electrical Safety Code IEEE C2. Unless marked or otherwise identified, the

Standard for the Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75, also applies.

Section 1.3.4

Radio Frequency (RF) Exposure

The WIN7000 is compliant with the requirements set forth in CFR 47, section 1.1307, addressing Radio

Frequency (RF) exposure from radio frequency devices as defined in OET Bulletin 65. The emitted radiation

should be as little as possible. To achieve minimum RF exposure, install the WIN7000 when it is configured not

to transmit and set it to operational mode remotely, rather than enabling transmission by the installer on-site. For

maintenance of the WIN7000, or other operations which require RF exposure, the exposure should be minimized

in time and according to the regulations set by the FCC or the regulations relevant to the country of installation.

Section 1.3.5

Lightning Protection

WARNING!

When the WIN7000 is installed in an outdoor location, all indoor components (such as Ethernet and

power supply) should be connected through a lightning protector.

Lightning protection protects people and equipment located indoors from lightning that might strike

the WIN7000 or its outdoor cables. Therefore, install the lightning protector device indoors, as close

as possible to the point where the cables enter the building. The lightning protector can also be

installed outdoors as long as the cables that lead indoors are well protected from lightning between the

protector and the building entrance.

Section 1.3.6

Power Cord Protection

Route all power supply cords so that people cannot walk on them or place objects on or against them. Walking on

the cords or placing objects on or against the cords can damage the cords.

Section 1.3.7

Servicing

Do not open the cover of this product to attempt service unless instructed by a RUGGEDCOM certified

technician. Refer all repairs to qualified service personnel. Removing the covers or modifying any part of this

device voids its warranty.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Zubehör Handbücher

Siemens

Siemens RUGGEDCOM WIN7225 Bedienungsanleitung

Siemens

Siemens Milltronics BW100 Bedienungsanleitung

Siemens

Siemens AP 257/41 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIWAREX JB Administratorhandbuch

Siemens

Siemens SIMATIC VS120 Bedienungsanleitung

Siemens

Siemens SIPART Series Administratorhandbuch

Siemens

Siemens SITRANS WW100 Bedienungsanleitung

Siemens

Siemens AP261 Bedienungsanleitung

Siemens

Siemens 3VL9400-4PJ00 Bedienungsanleitung

Siemens

Siemens QAF63 Series Gebrauchsanweisung

Siemens

Siemens Milltronics Millpulse 600 Bedienungsanleitung

Siemens

Siemens QBM3700 Series Bedienungsanleitung

Siemens

Siemens adm-i12w2 Bedienungsanleitung

Siemens

Siemens SITRANS AS100 Bedienungsanleitung

Siemens

Siemens QPM11 Series Bedienungsanleitung

Siemens

Siemens SITRANS WW300 Bedienungsanleitung

Siemens

Siemens SIWAREX WL200 Series Bedienungsanleitung

Siemens

Siemens TA1Q300 Bedienungsanleitung

Siemens

Siemens 4292 Series Bedienungsanleitung

Siemens

Siemens HL 3000 Bedienungsanleitung

Siemens

Siemens Milltronics MD-36 Bedienungsanleitung

Siemens

Siemens IR270CT Bedienungsanleitung

Siemens

Siemens 3VL9500 - 4W.30 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Bedienungsanleitung