Siemens SIMATIC ET 200S Bedienungsanleitung

SIMATIC ET 200S distributed I/O 2AI RTD HF analog electronic module (6ES7134-4NB51-0AB0)

_____________

Preface

Properties

Parameters

Diagnostics

Analog value representation

Connecting

SIMATIC

ET 200S distributed I/O

2AI RTD HF analog electronic

module (6ES7134-4NB51-0AB0)

Manual

05/2007

A5E01076876-02

Safety Guidelines

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.

CAUTION

without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.

NOTICE

indicates that an unintended result or situation can occur if the corresponding information is not taken into

account.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The device/system may only be set up and used in conjunction with this documentation. Commissioning and

operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes

in this documentation qualified persons are defined as persons who are authorized to commission, ground and

label devices, systems and circuits in accordance with established safety practices and standards.

Prescribed Usage

Note the following:

WARNING

This device may only be used for the applications described in the catalog or the technical description and only

in connection with devices or components from other manufacturers which have been approved or

recommended by Siemens. Correct, reliable operation of the product requires proper transport, storage,

positioning and assembly as well as careful operation and maintenance.

Trademarks

All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this

publication may be trademarks whose use by third parties for their own purposes could violate the rights of the

owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Siemens AG

Automation and Drives

Postfach 48 48

90327 NÜRNBERG

GERMANY

Ordernumber: A5E01076876-02

Ⓟ 09/2007

Technical data subject to change

이 기기는 업무용(A급) 전자파 적합기기로서 판매자 또는 사용자는 이 점을 주의하시기 바라며 가정 외의 지역에서 사용하는 것을 목적으로 합니다.

2AI RTD HF analog electronic module (6ES7134-4NB51-0AB0)

Manual, 05/2007, A5E01076876-02 3

Preface

Purpose of the manual

This manual supplements the

ET 200S Distributed I/O System

Operating Instructions.

General functions for the ET 200S are described in the

ET 200S Distributed I/O System

Operating Instructions.

The information in this document along with the operating instructions enables you to

commission the ET 200S.

Basic knowledge requirements

To understand these operating instructions you should have general knowledge of

automation engineering.

Scope of the manual

This manual applies to this ET 200S module. It describes the components that are valid at

the time of publication.

Recycling and disposal

Thanks to the fact that it is low in contaminants, this ET 200S module is recyclable. For

environmentally compliant recycling and disposal of your electronic waste, please contact a

company certified for the disposal of electronic waste.

Additional support

If you have any questions relating to the products described in these operating instructions,

and do not find the answers in this document, please contact your local Siemens

representative.

http://www.siemens.com/automation/partner

The portal to our technical documentation for the various SIMATIC products and systems is

available at:

http://www.siemens.com/automation/simatic/portal

The online catalog and ordering system are available at:

http://www.siemens.com/automation/mall

Preface

2AI RTD HF analog electronic module (6ES7134-4NB51-0AB0)

4 Manual, 05/2007, A5E01076876-02

Training center

We offer courses to help you get started with the ET 200S and the SIMATIC S7 automation

system. Please contact your regional training center or the central training center in D -

90327, Nuremberg, Germany.

Phone: +49 (911) 895-3200.

http://www.siemens.com/sitrain

Technical Support

You can reach technical support for all A&D projects

● using the support request web form:

http://www.siemens.com/automation/support-request

● Phone: + 49 180 5050 222

● Fax: + 49 180 5050 223

For more information about our technical support, refer to our Web site at

http://www.siemens.de/automation/service

Service & Support on the Internet

In addition to our documentation services, you can also make use of our comprehensive

online knowledge base on the Internet.

http://www.siemens.com/automation/service&support

There you will find:

● Our Newsletter, which constantly provides you with the latest information about your

products.

● The right documentation for you using our Service & Support search engine.

● The bulletin board, a worldwide knowledge exchange for users and experts.

● Your local contact for Automation & Drives in our contact database.

● Information about on-site services, repairs, spare parts. Lots more can be found on our

"Services" pages.

2AI RTD HF analog electronic module (6ES7134-4NB51-0AB0)

Manual, 05/2007, A5E01076876-02 5

Table of contents

Preface ...................................................................................................................................................... 3

1 Properties .................................................................................................................................................. 7

1.1 2AI RTD HF analog electronic module (6ES7134-4NB51-0AB0)..................................................7

2 Parameters.............................................................................................................................................. 17

2.1 Parameters...................................................................................................................................17

2.2 Parameter description..................................................................................................................20

3 Diagnostics.............................................................................................................................................. 21

3.1 Diagnostics using LED display.....................................................................................................21

3.2 Error types....................................................................................................................................22

4 Analog value representation .................................................................................................................... 23

4.1 Introduction ..................................................................................................................................23

4.2 Analog value representation for measuring range with SIMATIC S7 ..........................................23

4.3 Measuring ranges ........................................................................................................................25

4.3.1 Measuring ranges for thermoresistor...........................................................................................25

4.3.2 Resistance measurement ranges ................................................................................................29

4.4 Effect on analog value representation .........................................................................................30

4.4.1 Influence of the supply voltage and the operating state on analog input values .........................30

4.4.2 Influence of the value range on the Analog Input 2AI RTD HF ...................................................30

5 Connecting .............................................................................................................................................. 31

5.1 Connecting measuring sensors ...................................................................................................31

5.2 Wiring unused channels of the analog input modules.................................................................33

5.3 Using the shield connection .........................................................................................................33

Index........................................................................................................................................................ 35

Table of contents

2AI RTD HF analog electronic module (6ES7134-4NB51-0AB0)

6 Manual, 05/2007, A5E01076876-02

2AI RTD HF analog electronic module (6ES7134-4NB51-0AB0)

Manual, 05/2007, A5E01076876-02 7

Properties 1

1.1 2AI RTD HF analog electronic module (6ES7134-4NB51-0AB0)

Properties

● 2 inputs for resistance thermometer or resistance measurement

● Input ranges

– Resistance thermometers: Pt100; Ni100; Ni120; Pt200; Ni200; Pt500; Ni500; Pt1000;

Ni1000; Cu10; resolution max. 15 bits + sign

– Resistance measurement: 150 Ω; 300 Ω; 600 Ω; 3000 Ω; PTC; resolution max. 15 bits

● Automatic compensation of line resistances in the case of a three-wire connection

● Temperature coefficient can be assigned parameters for resistance-type sensors

● High accuracy

● Isolated from the load voltage

● Linearization of the sensor characteristic curves

● Permitted common-mode voltage 5 Vss AC

● Recording of reference junction temperature (together with the Electronic Module

2AI TC ST)

● Compatible with the 2AI RTD ST (6ES7134-4JB50-0AB50)

Note

The EM 2AI RTD HF can replace a 2AI RTD ST in an existing system.

•The wiring does not have to be changed. The additional bridges on the terminal

module of the 2AI RTD ST do not have to be removed.

•The configuration (in HW Config or the GSD file) does not have to be changed. Only

the new functions of the 2AI RTD HF cannot be assigned parameters in this instance.

Properties

1.1 2AI RTD HF analog electronic module (6ES7134-4NB51-0AB0)

2AI RTD HF analog electronic module (6ES7134-4NB51-0AB0)

8 Manual, 05/2007, A5E01076876-02

General terminal assignment

Note

Terminals 4, 8, A4, A8, A3 and A7 are only available at specified terminal modules.

Terminal assignment for 2AI RTD HF (6ES7134-4NB51-0AB0)

Terminal Assignment Terminal Assignment Notes

1 M

0+ 5 M

2 M

0- 6 M

3 I

C0+ 7 I

C1+

4 I

C0- 8 I

C1-

A4 AUX1 A8 AUX1

A3 AUX1 A7 AUX1

•Mn+: Measuring line positive, Channel n

•Mn-: Measuring line negative, Channel n

•IC0+: Constant current line positive, Channel n

•IC0-: Measuring line negative, Channel n

•AUX1: Protective-conductor terminal or potential bus (freely usable

up to 230 VAC)

Usable terminal modules

Usable terminal modules for 2AI RTD HF (6ES7134-4NB51-0AB0)

TM-E15C26-A1

(6ES7193-4CA50-

0AA0)

TM-E15C24-A1

(6ES7193-4CA30-

0AA0)

TM-E15C24-01

(6ES7193-4CB30-

0AA0)

TM-E15C23-01

(6ES7193-4CB10-

0AA0)

Spring terminal

TM-E15S26-A1

(6ES7193-4CA40-

0AA0)

TM-E15S24-A1

(6ES7193-4CA20-

0AA0)

TM-E15S24-01

(6ES7193-4CB20-

0AA0)

TM-E15S23-01

(6ES7193-4CB00-

0AA0)

Screw-type terminal

TM-E15N26-A1

(6ES7193-4CA80-

0AA0)

TM-E15N24-A1

(6ES7193-4CA70-

0AA0)

TM-E15N24-01

(6ES7193-4CB70-

0AA0)

TM-E15N23-01

(6ES7193-4CB60-

0AA0)

Fast Connect

















$8; 







$8;

















$$





























0

0

0

0

0

0

&

&

ZLUHZLUHZLUH

:LULQJH[DPSOHV

Properties

1.1 2AI RTD HF analog electronic module (6ES7134-4NB51-0AB0)

2AI RTD HF analog electronic module (6ES7134-4NB51-0AB0)

Manual, 05/2007, A5E01076876-02 9

Block diagram

$'&

$1$

9

/

0

















3

3

08;

(76

EDFNSODQHEXV

LQWHUIDFH

FRQQHFWLRQ

%DFNSODQHEXV

Figure 1-1 Block diagram of the 2AI RTD HF

Technical specifications for the 2AI RTD HF (6ES7134-4NB51-0AB0)

Dimensions and weight

Width (mm) 15

Weight Approx. 40 g

Module-specific data

Supports isochronous operation No

Number of inputs 2

Cable length

•Shielded Max. 200 m

Parameter length 7 bytes (4 bytes when used as 2AI RTD ST)

Address space 4 byte

Voltages, currents, potentials

Rated load voltage L+ (from the power module) 24 VDC

•Reverse polarity protection Yes

Power supply of the transducers Yes

•Constant-current supply for resistance-type

sensors Approx. 1.25 mA

•Short-circuit protection Yes

Electrical isolation

•Between the channels and backplane bus Yes

•Between the channels and load voltage L+ Yes

•Between the channels No

Permissible potential difference

•Between MANA and the central grounding point

(UISO) 75 VDC / 60 VAC

Insulation tested 500 VDC

Properties

1.1 2AI RTD HF analog electronic module (6ES7134-4NB51-0AB0)

2AI RTD HF analog electronic module (6ES7134-4NB51-0AB0)

10 Manual, 05/2007, A5E01076876-02

Current consumption

•From load voltage L+ Max. 30 mA

Power dissipation of the module Typically 0.6 W

Status, interrupts, diagnostics

Diagnostics function

•Group error Red LED "SF"

•Diagnostic functions readable Yes

Analog value generation

Measuring principle Integrating (sigma-delta)

Integration and cycle time/resolution per channel:

•Integration time can be assigned parameters Yes

•Interference frequency suppression in Hz 60 50

•Integration time in ms 16,7 20

•Basic conversion time incl. integration time in

ms 50 60

•Additional conversion time for wire break

check diagnosis in ms 5 5

•Additional conversion time in ms for line

compensation in three-wire connections 50 60

•Cycle time in ms Number of active channels per module x

conversion time

•Resolution (including overshoot range) Pt 100; Ni 100; Ni120; Pt 200; Ni 200; Pt 500; Ni

500; Pt 1000; Ni 1000; Cu 10 / 15 bits + sign

150 Ω; 300 Ω; 600 Ω; 3000 Ω; / 15 bits

PTC1 / 1 bit

Suppression of interference, limits of error

Noise suppression for

f = n x (f1 ± 1%), (f1 = interference frequency)

•Common-mode interference (USS)

•Series-mode interference

(peak interference value < rated value of input

range)

Min. 90 dB

min. 70 dB

Crosstalk between the inputs Min. -50 dB

Operational limit (in the entire temperature range,

with reference to the input range)

•Resistance-type sensor ± 0,1 %

•Pt100, Pt200, Pt500, Pt1000 Standard ± 1.0 K

•Pt100, Pt200, Pt500, Pt1000 Climatic ± 0.25 K

•Ni100, Ni120, Ni200, Ni500, Ni 1000 Standard

and Climatic ± 0.4 K

•Cu10 ± 1.5 K

Andere Handbücher für SIMATIC ET 200S

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens E/A-System Handbücher

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens FDCL221 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Benutzerhandbuch

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Technisches Dokument

Siemens

Siemens SIMATIC ET 200SP HA DQ 32x24VDC/0.5A HA Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens Simatic ET 200S 2/4AI RTD ST Bedienungsanleitung

Siemens

Siemens simatic ET 200MP Bedienungsanleitung

Siemens

Siemens Simatic ET200pro Bedienungsanleitung

Siemens

Siemens SIMATIC PROFINET Stücklistenhandbuch

Siemens

Siemens SIMATIC ET 200R Bedienungsanleitung

Siemens

Siemens SICAM A8000 Series Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP HA Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200AL Benutzerhandbuch

Siemens

Siemens FDCIO181-2 Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Technisches Dokument

Siemens

Siemens FDCIO222 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC S5 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200AL Benutzerhandbuch

Siemens

Siemens SIMATIC RQ 4x120VDC-230VAC/5A CO HA Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200eco PN Benutzerhandbuch

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung