Siemens SIREMOBIL Bedienungsanleitung

SIREMOBIL

English

Print No.: SPR2-130.812.06.01.02 Doc. Gen. Date: 12.02

Replaces: n.a.

The reproduction, transmission or

use of this document or its contents

is not permitted without express

written authority. Offenders will be

liable for damages. All rights, in-

cluding rights created by patent

grant or registration of a utility

model _or_design,_are_reserved.

System Manual

Installation Instructions

Installation of the Key Switch

SIREMOBIL SPR2-130.812.06 Page 2 of 6 Siemens AG

System Manual Rev. 01 12.02 CS PS 24 Medical Solutions

Installation and Startup1

Safety information 1

Validity of this document 1

This document is applicable if a key switch is to be retrofitted to the SIREMOBIL Compact,

SIREMOBIL Compact L, SIREMOBIL Iso-C, POWERMOBIL, and ARCOSKOP systems.

Documents required 1

•System manual of the product

Parts required 1

Tools required 1

•Tool case

•1 set of Allen keys

•1 drilling machine

•1 vacuum cleaner

Measuring equipment required 1

Avoidance of light to severe injuries which may even lead to

death and avoidance of material damage.

The product-specific safety information given in the system man-

ual as well as the safety information contained in the ARTD,

part 2, must be observed.

After all work has been completed and all covers have been

attached, perform the protective conductor test according to

ARTD-002.731.17. The protective conductor resistance must not

exceed 0.2 Ohm.

•Retrofit kit key switch 07140895

•Protective conductor resistance meter

e. g. "Safety Tester Bender UNIMET 1000 ST", Mat. No. 51 38 727

WARNING

Installation and Startup 3

Siemens AG SPR2-130.812.06 Page 3 of 6 SIREMOBIL

Medical Solutions Rev. 01 12.02 CS PS 24 System Manual

Mechanical installation 1

•Open the paneling of the logbook compartment.

•Open the rear paneling of the monitor trolley.

•A protective plate pointing towards the keyboard is installed inside the logbook compart-

ment. Unscrew this plate. Thus, the On/Off button is accessible.

•Mark the drill hole according to Fig. 1.

•Drill a 3.5 mm hole at the marked position (Fig. 1).

•Increase the hole diameter to 22 mm with the step drill (Fig. 1).

•Remove the remaining drilling chips in the monitor trolley with a vacuum cleaner.

Fig. 1 Fig. 2

Avoidance of light to serious injuries which may even lead to

death and avoidance of material damage.

Prior to performing the retrofit work, disconnect the system from

the power supply, and pull out the power plug.

Drill slowly. Make sure that during this process the step drill is

held at a right angle.

Collect the drilling chips inside the monitor trolley with an appro-

priate pad (such as cloth or plastic foil) to avoid short circuits due

to metal chips.

WARNING

Note

SIREMOBIL SPR2-130.812.06 Page 4 of 6 Siemens AG

System Manual Rev. 01 12.02 CS PS 24 Medical Solutions

4 Installation and Startup

•Insert the key switch into the hole from the outside. Make sure that the "0" mark at the

switch is in the vertical position.

•Slide the clamp fitting from the inside on the key switch.

The arrows of the lettering a1-4 mmapoint towards the protective plate.

•Tighten the screw (1/Fig. 3) clockwise, until the key switch is fixed firmly in the hole.

•Do not yet install the switch top (4/Fig. 4).

Fig. 3 Fig. 4

The key switch is delivered ready to assemble (Fig. 4).

For different plate thicknesses, the clamp fitting (1/Fig. 4) can be

pushed onto the key switch at two positions.

Make sure that the clamp fitting is installed with the arrows of the

lettering a1-4 mmapointing towards the key switch (2/Fig. 4).

Tighten the screw of the clamp fitting (2/Fig. 3) clockwise and

loosen it counterclockwise.

After having pressed the latch (1/Fig. 3) in the direction of the

arrow the switch top (4/Fig. 4) of the key switch can be removed.

The switch top can be placed on the key switch in three different

positions and then locked. In the center position the switch is not

actuated by the cams. Therefore, the switch top must be placed

off-center on the key switch and locked into place (3/Fig. 4).

Note

Installation and Startup 5

Siemens AG SPR2-130.812.06 Page 5 of 6 SIREMOBIL

Medical Solutions Rev. 01 12.02 CS PS 24 System Manual

Wiring 1

•Unplug the three-pin connector from the power button.

•Unplug connector D50.X5 on board D50.

•With the SIREMOBIL Iso-C, POWERMOBIL, and ARCOSKOP systems, the cable is ad-

ditionally equipped with the connector X5B. Remove it from the coupling as well.

•Run the new cable corresponding to the existing cable in the monitor trolley.

•Reconnect the 3-pin connector to the power button at the control console of the monitor

trolley.

•Run the two additionally existing cable ends to the key switch, and connect them to the

switch top of the key switch.

•Place the switch top off-center on the key switch and press it down, until it locks into

place.

•Plug in connector D50.X5 on board D50 again.

•With the SIREMOBIL Iso-C, POWERMOBIL, and ARCOSKOP systems, additionally re-

insert the connector X5B in the coupling.

Functional test 1

•Connect the system to the power supply.

•Check the function of the key switch:

- Turn the key switch into position 0. Press the On button at the monitor trolley and at the

basic unit, if existing.

Both times the system must remain switched off.

- Switch on the key switch and press the On button at the monitor trolley.

The system is started.

- After the end of startup, switch the system off. If the basic unit is equipped with an On

button, switch the system on again at the control console of the basic unit after it has

shut down.

The system is started.

- Turn the key switch into position 0.

The system switches off.

•After system shut-down, disconnect it from the power supply, and pull out the power

plug.

The cable between the power buttons (On/Off button at the control con-

sole of the monitor trolley) and the switch-on circuit D50 is replaced by

the cable included in the scope of supply.

Note

SIREMOBIL SPR2-130.812.06 Page 6 of 6 Siemens AG

System Manual Rev. 01 12.02 CS PS 24 Medical Solutions

6 Installation and Startup

Installing the paneling 1

•Reattach the protective plate behind the keyboard in the logbook compartment.

Take care that the cables are not squeezed.

•Refit the paneling of the logbook compartment. Make sure the ground wire connections

are correct when doing this.

•Reinstall the rear paneling of the monitor trolley. Make sure the ground wire connections

are correct when doing this.

Final work 1

•After all work has been completed and all covers have been attached perform the protec-

tive conductor test according to ARTD-002.731.17... The protective conductor resis-

tance must not exceed 0.2 Ohm.

•Add these instructions to the system manual of the product.

•File the Addendum/Supplement to the Operating Instructions included in the scope of

supply into the existing operating instructions.

Customer information 1

•Demonstrate the function of the key switch.

•Hand over the keys.

•Hand over the operating instructions.

Andere Handbücher für SIREMOBIL

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Medizinische Geräte Handbücher

Siemens

Siemens Drager medical Carina Bedienungsanleitung

Siemens

Siemens MOBILETT Plus Bedienungsanleitung

Siemens

Siemens ARCADIS Varic Installationshandbuch

Siemens

Siemens MODULARIS Uro Plus Montageanleitung

Siemens

Siemens ARCADIS Installationshandbuch

Siemens

Siemens POLYMOBIL Plus Betriebsanleitung

Siemens

Siemens LITHOSTAR Multiline Leitfaden

Siemens

Siemens SOMATOM Emotion Bedienungsanleitung

Siemens

Siemens SIREMOBIL Compact Gebrauchsanweisung

Siemens

Siemens ACUSON NX3 series Bedienungsanleitung

Siemens

Siemens ACUSON X300 Bedienungsanleitung

Siemens

Siemens SIREMOBIL Compact L Betriebsanleitung

Siemens

Siemens Healthineers UniPOC RAPIDPoint 500 Bedienungsanleitung

Siemens

Siemens POLYMOBIL Plus Installationshandbuch

Siemens

Siemens ARCADIS Varic Leitfaden

Siemens

Siemens MAMMOMAT Inspiration Gebrauchs- und Wartungshandbuch

Siemens

Siemens MOMMOMAT 1000 Anleitungen und Rezepte

Siemens

Siemens Servo Screen 390 Bedienungsanleitung

Siemens

Siemens ARCADIS Orbic Installationshandbuch

Siemens

Siemens SONOLINE G50 Bedienungsanleitung

Siemens

Siemens ACUSON X150 Bedienungs- und Wartungsanleitung

Siemens

Siemens ACUSON P10 Stücklistenhandbuch

Siemens

Siemens Prisma 3T Bedienungsanleitung

Siemens

Siemens SIRECUST 1280 Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung