Siemens SONOLINE G40 Bedienungsanleitung

SONOLINE G40™ ultrasound system

Quick Scan Card: General/OB For system software version 2.0

Press the Power Switch on the upper left side of the keyboard. A blue light will indicate the power is on.

Getting Started

Note: The term select is used to describe the action of rotating the S

Tcontrol (located lower left on control panel) to highlight the desired action and pressing

Tcontrol to execute.

Beginning an Exam

To enter data for a new patient:

1Press NEW PATIENT (F1).

2Enter the patient name, ID, and other pertinent information using the keyboard.

3Use TAB to move to next data field.

4Use TRACKBALL and cursor to select OK.

5If desired exam or transducer is not active, select correct Transducer or Exam from the drop down menus, press SET key.

6Exams can also be selected using EXAM key (F5) on keyboard.

Selecting a Transducer

Change the Transducer by pressing the Transducer button (cycles between the two transducers).

2D Imaging

To adjust... …do this:

More Penetration Toggle the TxFreq (soft) key down

Clean out noise/clutter Press THI button

Overall Gain/brightness Rotate 2-D knob

Depth Rotate DEPTH/ZOOM knob

Focus Rotate Focus control to position, Push down to add foci

Zoom Press DEPTH/ZOOM knob to select and rotate to zoom

Gain (to compensate for weak signals in specific areas) Adjust the positions of the DGC sliders

Steer 2D image (VF10-5) Press Steer/Angle. Rotate to steer image

Sector format (VF10-5) Roll SELECT control to highlight SECTOR in the control menu and press

select control

Rotate or Flip Image R/L

To change image orientation from up/down or left to right:

Rotate SELECT knob to highlight U/D (Up/Down) flip or L/R Left/Right flip (control menu) Press SELECT knob to activate

Annotating an Image

1Obtain an image, press Freeze.

2Press the TEXT key.

3Place text cursor where you would like the text to be displayed.

4Type text.

To Use Pre Programmed Text

1Press TEXT key.

2Toggle Library On (soft key menu)

3Rotate SELECT control to highlight desired text, press SELECT.

To Move Text

1Bring cursor next to the desired text to be moved.

2Press SET key to highlight (text turns green).

3Use TRACKBALL to move position of text to desired area.

4Press SET to lock text in place.

Removing Text from an Image

1Press DELETE WORD on keyboard to remove selected word.

2Pressing CLEAR SCREEN on Keyboard or CLEAR SCREEN soft key will remove all text, arrows and pictograms from screen.

Distance Measurement

1Press Freeze.

2Press CALIPER key.

3Place first caliper position, press SET key.

4Place subsequent caliper(s), press SET key. Measurement will be displayed on screen.

Distance Measurement with a Label

1Press Freeze.

2Press CALIPER key.

3Roll TRACKBALL to highlight measurement from on-screen menu, press SET key.

4Place first caliper, press SET key.

5Place subsequent caliper(s), press SET key. Measurement will be displayed on screen and transferred to Worksheet.

Measuring a Volume using 2D Imaging

1Acquire first image (Longitudinal), press Freeze.

2Press Caliper key.

3Select Volume measurement from SSOOFFTTKKEEYYmenu using toggle key.

4Roll TRACKBALL to position first cursor placement for length, press SET key.

5Roll TRACKBALL to position the second measurement marker, press SET key.

6Roll TRACKBALL to position the first measurement marker for the depth measurement, press SET key.

7Roll TRACKBALL to position the second measurement marker for the depth measurement, press SET key.

8Unfreeze the image, acquire transverse view, press Freeze.

9Press the CALIPER key on the control panel.

10 On the second image, roll TRACKBALL to position the first measurement marker for the width measurement, press SET key.

11 Roll TRACKBALL to position the second measurement marker, press the SET key. The system displays volume

measurement on screen

Note: Pressing the ESCAPE key during the volume measurement will erase the measurements that have been finished up to that point.

Circumference Measurement with a Label

1Press Freeze.

2Press Caliper Key.

3Rotate SELECT control to highlight measurement from on screen menu, press SELECT control.

4Place first caliper, press SET key.

5Place second caliper, press SET key.

6To adjust a caliper location- re-activate caliper by pressing the UPDATE key. (green is active)

7Roll TRACKBALL to adjust ellipse shape, press SET key. (Ellipse can be repositioned by rolling TB)

8Press SET key to complete measurement and send to Report.

Color and Power Doppler

To activate Color press Color Mode control. To exit press again or press 2D. To activate Power Doppler press Power Mode

control.

To adjust... …do this

ROI position Roll trackball

ROI size Press SET Key, roll trackball to adjust, press SET

Steer Press Steer/Angle control (only available on linear txs.)

Rotate to steer

Overall color/power gain Rotate color control

Frequency Toggle soft menu control

PRF (scale) Toggle soft menu control

Spectral Doppler

To activate Spectral Doppler press Doppler Mode key. Roll trackball to position cursor.

To adjust... …do this

Gate size Toggle soft key menu control

Overall Doppler gain Rotate Doppler mode

Steer Press Steer/Angle control and roll trackball to position cursor.

Angle Correct Press Steer/Angle control and rotate to adjust.

Frequency Toggle soft menu control

PRF (scale) Toggle soft menu control

Volume Toggle soft menu control

Baseline Toggle soft menu control

Obtaining OB Calculations

1Obtain desired image, press Freeze.

2Press CALIPER key.

3Rotate SELECT key to highlight desired measurement from on-screen menu, press SELECT key.

4Place first caliper, press SET key.

5Place subsequent caliper(s), press SET key. Measurement will be displayed on screen and transferred to Worksheet.

Siemens Medical Solutions USA, Inc

Ultrasound Division

1230 Shorebird Way

P.O. Box 7393

Mountain View, CA 94039-7393 USA

Headquarters

Siemens Medical Solutions USA

51 Valley Stream Parkway

Malvern, PA 19355-1406 USA

Telephone: +1-888-826-9702

www.usa.siemens.com/medical

Order No. A9117-5988-1C-4A00

05-17-PC-988 11-2005

Selecting Multiple Gestations

1Press CALIPER key.

2Roll TRACKBALL to top of Measurement menu to highlight B, C or D (default is singleton-A).

3In prompt box answer YES to multiple gestations question.

4Use TRACKBALL to select YES, press SET key.

Measuring the Heart Rate with M- Mode

1Press M-Mode key and obtain M-Mode cursor.

2Position cursor, press M-Mode key again for tracing.

3Obtain sweep, press FREEZE key.

4Press Caliper key.

5Select HR (heart rate) from SOFT KEY menu.

6Roll TRACKBALL to place measurement marker at the beginning of the cardiac cycle, press SET key.

7Roll TRACKBALL to place second measurement marker at the end of the first cardiac cycle, press SET key. Heart rate will

be displayed on screen and transferred to Worksheet

Editing Measurements in the Worksheet

1Rotate SELECT control to highlight Worksheet in the control Menu, press SELECT control.

2Roll TRACKBALL to the value to be deleted/edited, press SET key.

3Use the keyboard to delete or edit value.

4Press ENTER, system updates the value.

Measure AFI using 4B

1Rotate the SELECT control to highlight 4B in the control menu, press SELECT control.

2Obtain first quadrant image, press Freeze.

3Repeat process until 4 quadrant images have been obtained.

4Press CALIPER key.

5Rotate SELECT control to highlight Page, press to select page 2/3.

6Rotate SELECT control to highlight AFI menu, press SELECT control.

7Place first measurement marker, press SET key.

8Place second measurement marker, press SET key.

9Repeat this process in each quadrant.

10 Press 2D control to exit 4B.

Note: AFI will be displayed on screen and transferred to Worksheet.

DIMAQ: Reviewing and Selecting Images/Studies

To review images stored during an active exam

1Press Patient Browser key on the control panel.

2Active patient images stored will be displayed.

To review stored images/studies

1Press Patient Browser key on the control panel.

2Use TRACKBALL position cursor on patient name, press SET key.

3Roll trackball to select Image Screen button-press SET key.

To change display format

1Roll cursor to top left drop down menu.

2Position cursor over arrow, press SET key.

3Select desired format (1X1, 2X2, 3X3, 4X4 or 5X5) and release SET key.

4To advance images rotate SELECT knob.

To select multiple consecutive studies

1Select a single study.

2Place cursor on last patient name.

3Press Shift key and SET key.

To select multiple nonconsecutive studies

1Position cursor and hold Ctrl key for additional studies, press SET key.

Transfer Studies to CD

Press Patient Browser key on the control panel.

1Select EJECT button from menu-Insert CD.

2Select LOAD from patient browser menu-press SET key.

3Use TRACKBALL position cursor on patient name, press SET key.

4Wait until highlighted case turns “blue”.

5Select EXPORT from menu-press SET key.

6Status of export displayed on bar under export.

7Select EJECT from menu-press SET key.

8Remove CD from CD-driver. Press Escape to leave Patient Browser or select Live Screen to Resume Scanning.

Powering off System:

Turn off system by pressing blue power switch located on the upper left side of the keyboard.

* Press once for STANDBY mode

*Press and hold to Power system OFF

Note: Wait until monitor goes black before removing power cord from wall.

Refer to the system’s user and reference manuals for safety information (warnings, cautions, and explanations of symbols and labels),

complete operating instructions and technical specifications, and procedures for system and transducer care (cleaning and disinfecting

procedures).

Siemens reserves the right to change system specifications at any time.

Inhaltsverzeichnis

Andere Siemens Medizinische Geräte Handbücher

Siemens

Siemens ARCADIS Varic Bedienungs- und Wartungsanleitung

Siemens

Siemens VB 13C Bedienungsanleitung

Siemens

Siemens MAMMOMAT 300 Gebrauchs- und Pflegehandbuch

Siemens

Siemens ACUSON X150 Bedienungs- und Wartungsanleitung

Siemens

Siemens Drager medical Carina Bedienungsanleitung

Siemens

Siemens MTCO 1324 Bedienungsanleitung

Siemens

Siemens MAMMOMAT Novation DR Bedienungsanleitung

Siemens

Siemens Rapidlab 1200 Handbuch

Siemens

Siemens MULTIMOBIL 5C Bedienungsanleitung

Siemens

Siemens SIREMOBIL Compact Gebrauchsanweisung

Siemens

Siemens ACUSON Freestyle Bedienungsanleitung

Siemens

Siemens MAMMOMAT 1000 Nova Bedienungsanleitung

Siemens

Siemens MOBILETT XP Bedienungs- und Wartungsanleitung

Siemens

Siemens POLYMOBIL III Installationshandbuch

Siemens

Siemens SOMATOM Sensation 16 Benutzerhandbuch

Siemens

Siemens POLYMOBIL Plus Bedienungs- und Wartungsanleitung

Siemens

Siemens ARCADIS Varic Bedienungsanleitung

Siemens

Siemens MAMMOMAT NovationDR Bedienungsanleitung

Siemens

Siemens MAMMOMAT 1000 Nova Bedienungs- und Wartungsanleitung

Siemens

Siemens Uroskop ACCESS Bedienungsanleitung

Siemens

Siemens MULTIMOBIL 10 Bedienungsanleitung

Siemens

Siemens acuson Sequoia Installationsanleitung

Siemens

Siemens MAMMOMAT Novation DR Bedienungsanleitung

Siemens

Siemens Drager medical Carina Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung