Siemens MULTIMOBIL 10 Bedienungsanleitung

MULTIMOBIL 10

English

Print No.: SPR8-X01.812.10.02.02 Doc. Gen. Date: 10.05

Replaces: SPR8-X01.812.10.01.02

The reproduction, transmission or

use of this document or its contents

is not permitted without express

written authority. Offenders will be

liable for damages. All rights,

including rights created by patent

grant or registration of a utility

model _or_design,_are_reserved.

Installation Instructions

Service Manual

Installation Instructions

Siemens Ltd. Med Division India Version 4.0 Page 1 of 12

Installation Instructions

Version: 4.0

The reproduction, transmission or use

of this document or its contents is not

permitted without express written

authority. Offenders will be liable for

damages.

Multimobil 10

Med

Service Manual

Installation Instructions

Siemens Ltd. Med Division India Version 4.0 Page 2 of 12

INDEX

1 INSTALLATION ............................................................................................................................ 3

1.1 SAFETY PRECAUTIONS................................................................................................................ 3

1.2 OVERLOAD PROTECTION : ........................................................................................................... 4

1.3 RADIATION PROTECTION : ........................................................................................................... 4

1.4 MECHANICAL SAFTEY :................................................................................................................ 4

1.5 UNPACKING ................................................................................................................................5

1.6 TRANSPORT AND POSITIONING OF UNIT ....................................................................................... 6

1.7 PRELIMINARY CHECK : ................................................................................................................ 6

1.7.1 Mains : ............................................................................................................................. 6

1.7.2 Interconnections .............................................................................................................. 6

2 SWITCHING THE UNIT ON .........................................................................................................7

2.1 FORMING OF THE CAPACITOR BANK:............................................................................................ 8

2.2 COLLIMATOR :............................................................................................................................. 9

2.3 MOVEMENTS :........................................................................................................................... 10

2.4 EXPOSURE ............................................................................................................................... 10

2.4.1 Sample Exposure: ......................................................................................................... 11

3 HANDING OVER MULTIMOBIL 10............................................................................................ 12

Service Manual

Installation Instructions

Siemens Ltd. Med Division India Version 4.0 Page 3 of 12

1 Installation

1.1 Safety Precautions

General:

It shall be the duty of the installation personnel and the user to ensure that all the

safety measures concerning the unit operation and installation are adhered to.

The unit must be checked for the status of its safety measures at least every year or

any time desired by the user, not exceeding one year.

However, we recommend in the interest of the safety of the patient, the user, and

other personnel to have a yearly drill on operational safety.

If there are any special regulations of the hospital/institute, to be followed over and

above the general safety regulations pertaining to the installation, the same must be

ensured.

Before commencing the operation, the user must convince himself regarding all safety

aspects and their proper functioning. He should also ascertain that all displays and

indicators are functioning as described.

The radiation indication lamp should light only when the exposure is released. In case

the lamp lights in any other condition, the unit should be immediately switched off and

SIEMENS SERVICE DEPARTMENT should be informed.

Any change / or replacement in the unit must be carried out by the manufacturer or a

person authorised by manufacturer ONLY. The record of such work must be

maintained clearly at the site.

Before working on the unit ensure that the Mains is switched OFF.

For completely safe working remove mains plug.

The unit must be OFF before removing or putting back the assemblies.

The protective earthing of sub-assemblies must not be removed in any case.

Service Manual

Installation Instructions

Siemens Ltd. Med Division India Version 4.0 Page 4 of 12

1.2 Overload Protection :

The unit is designed to work between 99 V to 121 V on 110 V or 180 V to 265 V on

230 V line ac single phase supply with a 15A socket. For safety purposes 10A HRC

fuses are provided which will blow when a current exceeding 10A sustains for its

response time.

Ensure that the mains socket is properly earthed.

In case of fault if the kV tries to build beyond the safe limit of X-ray tube the protection

circuit blocks the HT.

In case of fault, if the Filament current tries to increase beyond the safe limit the

protection circuit blocks filament boosting.

1.3 Radiation Protection :

Do not put any part of your body in the direct line of radiation.

Collimate the X-ray beam.

Keep maximum possible distance from the object being radiographed. For this

make the best use of 5m of recoilable exposure release switch.

Wear protective clothing.

Monitor radiation received using the personal TLD-badges or pen-dosimeter.

1.4 Mechanical Saftey :

Before releasing arm assembly from its locking position, ensure that the single tank

assembly along with covers, yoke and collimator is in the original position.

In case a difficulty is encountered in releasing the lock, any adjustments or alignments

must be done with complete single tank assembly in the locked position only.

Do not attempt to release the lock by any other means.

The arm will not be counter-balanced if any of the single tank assembly parts like

cover are removed.

Any detection of physical damage of single tank assembly or breaking or loosening of

its parts (except handles) indicates possible danger of upward force the order of 25kg,

when the arm is released from its locked position. In such a situation, it is

recommended to suspend the installation and contact FACTORY for further

clarification.

Service Manual

Installation Instructions

Siemens Ltd. Med Division India Version 4.0 Page 5 of 12

1.5 Unpacking

Service Manual

Installation Instructions

Siemens Ltd. Med Division India Version 4.0 Page 6 of 12

1.6 Transport and Positioning of Unit

Refer corresponding section on Transporting the Unit and Positioning for Exposures in

the Operating Instructions.

1.7 Preliminary Check :

1.7.1 Mains :

1. Check available mains voltage at the site either 110 V or 230 V AC.

2. Check if the mains voltage is between 99 V to 121 V ac or 180 Vac to 265 Vac

respectively.

3. The unit is set for respective line voltage at the time of despatch from factory.

5. When the mains voltage is less than 205V on 230 V ac line, than the LN contactor

is energised for line condition compensation circuit.

6.Check if the mains resistance is < 1.2 Ω.

1.7.2 Interconnections

Type Description Specifications

Mains 1 Mains Cable 3 x 1.5 sq.mm

Control - single Tank

Control Single Tank

D915.X8, X1 Connector 3 Core shielded PVC insulated, kV/mA feedback

Cable

D801.X60 Allied Connector 2 Core 1 mm sq. Grey, Collimator Cable

D801.X5 11/12 - D900A 2 Core shielded PVC insulated, Filament cables

11 & I2

D801.X3 0,I,II - D900A 3 Core shielded PVC insulated , Anode Rotation

cable.

D960 (out1) and

capacitor C6

U,V - D900A 6 mm sq. Black U & V Cables

Earthing terminal Earthing stud 6 mm sq Yel/Green Earth Cable

Interconnections

D915.X11 to D801.X11 Flat Band 16 core.

D915.X10 to D801.X10 Flat Band 26 Core.

D915.J24 to D932.X1 Flat Band 28 Core.

D915.X20 to D960.X20 to D950A .X20 Flat Band 20 Core.

D915.X12 to D936.X12 Flat Band 14 Core.

D915.X15 to D980.X15 Flat bonded cable K7

D801.X9 to D980 .X9 SMPS Mains cable K12

Wire bunch to D801.X1 10 pin molex connector

Wire bunch to D801.X50 3 pin molex connector

Wire bunch to D801.X18 6 pin molex connector

Contactor CS to X3.D950A Charger cable S4 with 6 pin connector

Bleeder resistor to X9.D950A 3 pin connector discharge cable

The max. Permissible resistance between the earthing terminal in the control and the

single tank is less than 0.2 ohms.

Service Manual

Installation Instructions

Siemens Ltd. Med Division India Version 4.0 Page 7 of 12

2 Switching the unit ON

Switch ON the MCB .

If the unit is being installed within six months from the date of despatch then the

forming is not required for the Capacitors. Before Switching ON the Unit open

the top panel cover of MM10 control by removing the ornamental screws (2x)

and remove the ST link (jumper pin) on D915 PCB

Switch the Generator ON by actuating momentarily

The Display and radiation Indicator light up.

The kV and mAs display read

for 3 Sec and then the stable mAs value appear. Once the Capacitor Bank is charged

to a value of 355V DC, then the stable kV value appears and it is indicated by a long

Beep

The unit becomes ready for use after this end of setup

After set-up, initial hardware checks and capacitor bank fully charged to 355V DC the

display changes to

the default kV and mAs settings.

The kV & mAs display and settings will now respond to the corresponding switches on

the panel.

MCB

Service Manual

Installation Instructions

Siemens Ltd. Med Division India Version 4.0 Page 8 of 12

In case of any errors while setting up / hardware check / stand-by operation, the

corresponding Error code will be displayed on the same displays.

e.g. The display will indicate Error 99 in case the unit while setting up/ after setup

detects that last reset of the unit was due to watch-dog timer RESET.

Note: The Control Unit contains Non volatile Memory which retains the last

selected kV and mAs. So the initial display after setup will depend on the last

settings done.

If the unit is being installed after six months from the date of despatch then the

forming for the Capacitors is a must.

2.1 Forming of the Capacitor Bank:

Open the top panel cover of MM10 control by removing the ornamental screws (2x)

and put the ST link (jumper pin) on D915 PCB.

Switch ON the MCB .

Switch the Generator ON by actuating momentarily

Then the kV and mAs display read as shown in picture, if there are no initialisation

Errors.

MCB

Service Manual

Installation Instructions

Siemens Ltd. Med Division India Version 4.0 Page 9 of 12

On D936 keyboard PCB,

1. Press DL-SERV switch once, the display will indicate the present Voltage on the

Capacitor bank.

2. Press once again DL-SERV switch, the display will indicate Pr.1

3. Press again the DL-SERV switch the CS contactor will hold and the

Capacitors will start charging in described steps as follows:

0V – 50 – 100 – 150 – 225 – 300 – 342 V .

Each step will take about 6 minutes, so total procedure of Capacitor bank

Forming will take 36 minutes.

4. Now switch OFF the unit and remove the ST link (jumper pin) on D915 PCB.

2.2 Collimator :

Switch the unit ON

Switch ON the collimator lamp. The collimator lamp will glow for 30 sec ±5 sec.

Open collimator flaps to the maximum. The light will show square, sharp edges and

clear cross wires.

Close the flaps fully. The light field will show a small square.

Andere Handbücher für MULTIMOBIL 10

Inhaltsverzeichnis

Andere Siemens Medizinische Geräte Handbücher

Siemens

Siemens MAMMOMAT 1000 Nova Handbuch

Siemens

Siemens LITHOSTAR Multiline Leitfaden

Siemens

Siemens Servo Screen 390 Bedienungsanleitung

Siemens

Siemens ARCADIS Varic Bedienungs- und Wartungsanleitung

Siemens

Siemens ARCADIS Varic Bedienungsanleitung

Siemens

Siemens ACUSON X300 Bedienungsanleitung

Siemens

Siemens SOMATOM Spirit Bedienungsanleitung

Siemens

Siemens Prisma 3T Bedienungsanleitung

Siemens

Siemens MAMMOMAT Balance Bedienungsanleitung

Siemens

Siemens MAMMOMAT Inspiration Gebrauchs- und Wartungshandbuch

Siemens

Siemens ACUSON Cypress Bedienungsanleitung

Siemens

Siemens ACUSON Freestyle Bedienungsanleitung

Siemens

Siemens Uroskop ACCESS Bedienungsanleitung

Siemens

Siemens SIREMOBIL Iso-C Gebrauchsanweisung

Siemens

Siemens MAMMOMAT 1000 Nova Technische Daten

Siemens

Siemens MAMMOMAT Novation DR Gebrauchs- und Pflegehandbuch

Siemens

Siemens SOMATOM Emotion 6 Benutzerhandbuch

Siemens

Siemens Healthineers UniPOC RAPIDPoint 500 Bedienungsanleitung

Siemens

Siemens MAMMOMAT 300 Anleitungen und Rezepte

Siemens

Siemens ARCADIS Varic Installationshandbuch

Siemens

Siemens SIREMOBIL Bedienungsanleitung

Siemens

Siemens Sonoline G20 Bedienungs- und Wartungsanleitung

Siemens

Siemens MAMMOMAT 3000 Bedienungsanleitung

Siemens

Siemens ARCADIS Avantic Installationshandbuch

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung