Sirius Satellite Radio SIU3 Bedienungsanleitung

Models covered by this instructions:

SIU3, SIU5, SU404, SU405, SU401, SIU14, SIU24, SIU8

*** BEFORE INSTALLATION ***

ENSURE THERE IS NO VISIBLE OR HIDDEN DAMAGE

SUSTAINED DURING SHIPPING

*** SHIPPING DAMAGE ***

MUST BE REPORTED WITHIN 5 DAYS OF RECEIPT

INSTALLATION

INSTRUCTIONS

CARE AND USE MANUAL FOR:

ISLAND RANGE HOODS

WARNING

Thank you for purchasing a Sirius Range Hood.

Please read all the instructions in this manual before

installing the appliance.

Save these instructions for future reference.

Only use this appliance as an exhaust ventilation system for the removal of coo-

king vapors. DO NOT use to expel ammable substances or any other materials

or vapors.

The installation procedures in this manual are intended for qualied installers, ser-

vice technicians or persons with similar qualied background.

DO NOT attempt to install this appliance yourself.

Ensure that electrical power is turned off at source before commencing installation.

All electrical wiring must be properly installed, insulated and grounded and conform

to all applicable codes and standards.

Make sure all existing duct work is clean of grease build up, or duct work should be

replaced, if necessary, to avoid the possibility of a grease re. Check all joints on

ductwork to ensure proper connection and all joints should be properly taped. Be

careful when cutting through ceilings or walls not to damage any hidden pipes or

electrical wiring. Ensure your kitchen has sufcient air return vents to replace the

exhausted air.

Fan ducts should always be vented to the outside of your home and never into

spaces within walls, ceilings, lofts or attics. Only use rigid, smooth steel for ducting.

The exhaust point of the blower requires a 6” round or 8” connection.

TABLE OF CONTENTS

BEFORE YOU BEGIN 4

MINIMUM AND MAXIMUMS 4

DUCTING 4

Duct Run Calculation 5

ELECTRICAL 5

Electrical Supply 5

INSTALLATION 6

Structural preparation for the hood fan installation 6

Fixing the Main Support Bracket 6

Attaching the range hood to the ceiling 7

Connecting Electricity and Ducting 8

Re-Circulating Requirements 8

Schematic of modular island components 9

OPERATING PROCEDURES 11

General Advice 11

Functions 11

MAINTENANCE 14

Cleaning the Filter 14

Cleaning the Hood 14

Substitution of the LED bar 15

WARRANTY 16

BEFORE YOU BEGIN: It is advisable to

test run the range hood before installa-

tion.

BEFORE STARTING – please read this

entire document and ensure you are fully

conversant with the require-ments and li-

mitations. These units weigh approximately

125lbs and therefore require a minimum of

two people to install.

BEFORE YOU BEGIN

The manufacturer declines all responsibility

in the event of failure to observe the instruc-

tions given here for installation, maintenan-

ce and suitable operation of the product. The

manufacturer further declines all responsibi-

lity for injury due to negligence and the war-

ranty of the unit automatically expires due

to improper maintenance and/or installation.

Use the shortest most direct ductwork rou-

te possible. Only use metal ducting - plastic

ducting is generally not permitted by code.

Do not use exible metal ducting as the rid-

ges of the ducting cause severe air turbulen-

ce and will signicantly reduce the efcien-

cy of any hood -THIS TYPE OF DUCTING

WILL REDUCE EFFICIENCY BY 50%.

Vent hoods may interrupt the proper ow of

exhaust gases from re-places, gas furna-

ces and gas water heaters. To minimize the

risk of drawing these lethal gases back into

the home please follow the heating equip-

ment manufacturers safety standards and

guidelines. Refer to NFPA and ASHRAE for

additional information.

DUCTING

If vented externally, 6” / 150mm round duc-

ting must be available for the hood through

the ceiling, in line with the central vertical

axis of the range hood.

If i’s gas range or cook top recommanded

8”.

This unit must have it’s own ductwork. Do

not under any circumstances vent this unit

into any other ductwork or exhaust ducting

in the building.

PLEASE NOTE THAT THE DUCT OUT-

LET ON THE TOP OF THE POWER UNIT

IS OFF SET FROM CENTRE AND THE-

REFORE AN ADJUSTABLE 6” ROUND

BEND WILL BE REQUIRED TO LINE THE

EXHAUST OUTLET WITH THE 6” HOLE IN

THE CEILING MOUNT BRACKET.

MINIMUM AND MAXIMUMS

Min length of power unit structure with de-

ector connected = 36.6”

Min length of power unit without deector = 32”.

Max length of power unit structure = 48”.

Recommended height from cook top to un-

derside of hood = 30” for gas, 25” for electric.

Maximum Run

6” or 3 1/4 x 10” duct * 100 FT

Deduct

Each 90 elbow used 15FT

Each 45 elbow used 9FT

Each 6” or 3 1/4 x 10” duct

Transition used 1FT

Each 3” 1/4 x 10” to 6”

Transition used 5FT

Side Wall with damper 30FT

Roof Cap 30FT

Duct Run Calculation.

The maximum duct run before effecting the

performance of the hood is 100’. Calculate

your duct run by measuring linear feet and

adding the elbows, transitions and caps ba-

sed on the table below.

* Gas range or gas cook top recommanded

8”.

Electrical Supply.

This appliance requires 120V/60Hz, 3amp

electrical supply - ensure an appropriately

qualied person completes the electrical ho-

ok-up. The connection point for the electrical

supply is at the top of the unit, therefore the

electrical supply must be run down from the

ceiling alongside the ductwork.

All electrical and venting hook-ups must be in

place before commencing installation of the

hood-fan.

ELECTRICAL

WARNING: All electrical work must be

performed by a qualied electrician.

Please ensure that the appropriate electrical

codes or prevailing local building codes and

ordinances are adhered to.

Ensure that the electricity supply is discon-

nected at source. Do not use an extension

cord or adapter plug with this appliance.

This appliance must be grounded. Connect

to a properly grounded branch circuit, pro-

tected by a 15 amp circuit breaker.

Structural Preparation for the Hood Fan

Installation.

The island hood weighs approximately 125

lbs. It is therefore imperative that a substan-

tial structure is prepared in the ceiling to at-

tach the range hood to. Ideally block off an

area of at least 12”x12” between the ceiling

joists using 2x4’s. Allow for a hole through

the center of this blocking of at least 6” in

diameter through which to pass the duct-

work and electrical cable.

The underside of the hood must not be clo-

ser than 30” from the cook-top and ideally

not higher than 32”above the cook-top. It is

strongly recommended, at this point, that

calculations and measurements be made

and all planning and heights be nalized.

You will need to t the appropriate length of

ducting to the hood fan before installing it to

the ceiling.

Planning should consist of a test assembly

of the power unit and telescoping structure

before attempting to mount everything to the

ceiling. By following this test assembly you

will be able to nalize the correct length of

the assembly before mounting it to the cei-

ling.

Test assembly should include actually at-

taching the following items together – refer

schematic of components and “Fixing the

main support brackets” below – Brackets

A, B, C, power unit and deector if re-circu-

lating.

This is also a good time to test the electrical

functioning of the hood before it is installed.

Before switching on the light or lights, ensu-

re the tape holding the globes in place has

been removed.

The globes gets extremely hot and will very

quickly burn the tape and discolor the glo-

bes irreparably.

INSTALLATION

Do not switch on the lights with the hood at

on any surface as the in-tense heat will burn

the surface and destroy the lamps. Connect

a power supply to the unit and test all fun-

ctions.

Installation of the island hood consists of -

xing the ceiling Bracket A substantial mem-

bers in the ceiling. The bracket must be xed

to the frame by screwing through the ceiling

into the heavy members inside the ceiling.

This is critically important as the entire

hood fan hangs from this position, and

ceiling board alone will not support the

weight of the hood fan. Discard the plastic

wall plugs supplied for xing the bracket to

the ceiling - these are not appropriate for

North American structures.

Fixing the Main Support Brackets

Using Bracket “A” as a template mark the cei-

ling where the xing screws “A” will be posi-

tioned - remember the correct orientation

from above. Attach bracket “A” to the ceiling

permanently. If re-circulating, attach the de-

ector to Bracket “A” before xing it to the

ceiling – refer schematic on page 5.

The 2 brackets for the support of the chimney

(Part A) is to be installed to Bracket A with

the screws (C Fig.1) Fix the structure on the

ceiling by inserting the 2 dowels.

g. 1

Fix Bracket “C” to the power unit with the

nuts and washers supplied (Items “A” on the

schematic on page 5). Please ensure that

the bracket is installed as shown to enable

full ac-cess to the square plastic black box

and the metal electrical junction box. Slide

Bracket “B” over Bracket “C” (once again

ensure full access to the plastic and electri-

cal boxes is main-tained) and x it in place,

at the previously calculated length using the

machine screws denoted by items “B” on the

schematic on page 5.

Check that the plastic aps at the exhaust

outlet for the fan move freely and have not

become jammed during shipping or whilst

working with the power unit. Connect an ap-

propriate length of ducting to the unit.

Do not x the ducting to the outlet with

screws - use DUCT TAPE.

Only for SU 401,SIU3, SIU5, SIU14, SIU24:

Install the glass as per the instructions con-

tained in the packaging of the glass. (only

for SU401).

Stand the assembled structure on a clean

soft surface. Ensure the underside of the

hood does not get scratched and slide the

chimneys of the assembled structure from

the top down as per the schematic on page

5. Ensure that the holes for xing the deco-

rative chimney are correctly orientated with

the holes at the top of bracket A.

Attaching the Range Hood to the Ceiling.

The entire structure that has been pre-as-

sembled above, must now be hoisted up to

the ceiling. A few things have to happen at

once here: the slots (as discussed below)

need to be engaged and the ductwork must

make connection with the length of ductwork

on the structure.

This will require two strong people –do not

attempt this step on your own. Bracket “B”

has slots, position C per Diagram “A” (refer

to page 5), at the top that will receive the

spring clips located on Bracket “A” -THIS IS

A TEMPORARY HOLD ONLY –DO NOT

RELY SOLELY ON THESE CLIPS TO

HOLD THE HOOD UP – THEY WON’T.

Once “hooked” by the spring clips immedia-

tely secure the structure with the machine

screws at point “E” on the schematic on

page 5 – this must be done immediate-

ly and should not be skipped. Raise the

upper chimney to the ceiling and x it to the

bracket “A” with the screws supplied “D”.

Ensure the entire structure is sturdy - serious

injury, death and MAJOR damage could re-

sult should the unit not be well connected to

the frame structure within the ceiling.

This is of utmost importance - do not go any

further until this has been tested and double

checked - the installer has sole responsibi-

lity for the safe installation of this product.

Only for SU 404-405: Stand the assem-

bled structure on a clean soft surface. En-

sure the underside of the hood does not get

scratched and slide the chimneys of the as-

sembled structure from the top down as per

the schematic on page 5. Ensure that the

holes for xing the decorative chimney are

correctly orientated with the holes at the top

of bracket A.

This will require two strong people –do not

attempt this step on your own. Bracket “B”

has slots, position C per Diagram “A” (refer

to page 5), at the top that will receive the

spring clips located on Bracket “A” - THIS

IS A TEMPORARY HOLD ONLY - DO

NOT RELY SOLELY ON THESE CLIPS

TO HOLD THE HOOD UP - THEY WON’T.

Once “hooked” by the spring clips immedia-

tely secure the structure with the machine

screws at point “E” on the schematic on

page 5 - this must be done immediately

and should not be skipped.

Ensure the entire structure is sturdy- serious

injury, death and MAJOR damage could re-

sult should the unit not be well connected to

the frame structure within the ceiling.

This is of utmost importance – do not go any

further until this has been tested and double

checked – the installer has sole responsibi-

lity for the safe installation of this product.

Once the entire structure has been xed to

the ceiling slide the chimneys on the assem-

bled structure from the bottom up as per the

schematic on page 5. And x the chimneys

with the screws supplied. Raise the upper

chimney to the ceiling and x it to the bra-

cket “A” with the screws supplied “D”.

Connecting Electricity and Ducting.

Make sure power is turned off at the source.

Make the electrical connection (see gure

2). Test the functioning of the hood. Slide the

upper chimney into place and attach with

the machine screws provided to Bracket “A”.

Re-Circulating Requirements.

Fit the carbon lter after the installation is

complete – these t in behind the aluminum

grease lter.

A short length of ductwork must be connec-

ted from the exhaust outlet up to the deector

(must be purchased with hood).

The deector, after attaching part B with

screws E connects to the top of Bracket “A”

and forces the air out through the grills on

the side of the chimney section back into the

room. (see diagram C).

g. 2

Diagram c - Deector

Bracket

Deector FOR SU404

Part B

Deector FOR SU405

Part B

Deector FOR SIU3, SIU5

Deector attaches to ceiling mount bracket when island hood is installed in re-circu-

lating mode and the air that has passed through the fat and carbon lters is returned

to the room via a short length of 6” round ductwork attached to the power unit and

deector.

Diagram b – Securing Bracket “A” to “B”

Please note – this is critically important - do not rely on the spring clips.

Diagram A – Main Assembly

FOR SU404

Andere Handbücher für SIU3

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sirius Satellite Radio Dunstabzugshaube Handbücher

Sirius Satellite Radio

Sirius Satellite Radio SIU3 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SDD2ELEMTC Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT950 EM Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio S-DDH3 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL909 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC EM 97 900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL85 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT972 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUT950 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SILT-26 Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU35 TC Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT950 EM Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio Essence S-DD 16 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT972 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SIL-EM490X Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SEM51 Leitfaden

Sirius Satellite Radio

Sirius Satellite Radio Valentina SLT958EM Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio Downdraft S-DD18 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUF1 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL906EM-L 520 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SILT18 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SILT-26 Series Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUM Series Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch