Sirius Satellite Radio SL926 Series Bedienungsanleitung

SL926 series

UNDERMOUNT RANGEHOOD INSTALLATION INSTRUCTIONS

Congratulations on your purchase!

Thank you for choosing a Sirius product.

SL926 DL 520 EAN #9351116002701

SL926 DL 850 EAN #9351116002718

www.siriusbrand.com

The symbol on the product or on its packaging indicates that this product

may not be treated as house-hold waste. Instead it shall be handed

over to the applicable collection point for the recycling of electrical and

electronic equipment. By ensuring this product is disposed of correctly,

you will help prevent potential negative consequences for the environment

and human health, which could otherwise be caused by inappropriate

waste handling of this product. For more detailed information about

recycling of this product, please contact your local city office, your

household waste disposal service or the shop where you purchased the

product. This appliance is marked according to the European directive

2002/96/EC on waste electrical and electronic equipment (WEEE).

Sirius warranty covers only Sirius product. If you choose to install a non-Sirius branded accessory

such as flexible ducting, Sirius will only warrant the rangehood and motor. If installation is found to be

the cause of failure or issue then charges will apply for service and parts.

Flexible ducting is not permitted under any circumstances. Flexible ducting has been found to

increase noise levels, increase vibration and reduce airflow. Sirius Semi-rigid or solid ducting can be

used in lieu. There is a range available to suit any application.

Ducting available at www.siriusbrand.com

6 Year Warranty when Sirius Ducting is used. Full replacement warranty on parts and labour.

See website for terms & conditions.

A reduction in the duct diameter from stated ducting size will void warranty.

If you are in doubt about the ducting, please contact Sirius on 1300 762 219 prior to installation

WARNING

The appliance must be installed and

connected to the power supply only by a

qualified technician.

• There should be adequate ventilation of the room when the rangehood is used at the same time as

appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the

room)

• The details concerning the method and frequency of cleaning

• There is a fire risk if cleaning is not carried out in accordance with the instructions;

• Do not flambé under the range hood;

• CAUTION: Accessible parts may become hot when used with cooking appliances.

BEFORE YOU INSTALL - DUCTING INFORMATION

Min. 600mm - Max. 700mm for induction cooktops.

Min. 650mm - Max. 750mm gas cooktops.

If the rangehood is positioned above the max height

recommended, warranty may be compromised

as performance of the rangehood will be affected.

Measurement is taken from the top of the trivets to

the underside of the hood. (Fig.1)

• The air being drawn can’t be conveyed through

or into a duct used to let out fumes from

appliances fed by energy other than electric

power (eg. centralized heating, radiators, water

heaters, etc.).

• Attention: remove any possible PVC film from the

stainless steel, including the filters.

• To externally vent, please comply with the

pertaining rules given by competent authorities.

• Provide the room with an adequate ventilation

when a rangehood and appliances fed by energy

other than electric power (gas, oil, or coal stoves,

etc.) are used simultaneously. The rangehood,

when evacuating the air, could generate a

negative pressure in the room which can’t exceed

the limit of 0.04 mbar, in order to avoid the

suck of exhausts deriving from the heat source.

Therefore the room should be provided with air

intakes to allow a constant flow of fresh air.

If the rating label in the rangehood shows the symbol

, the appliance is built in class II° and it does not

need any earth connection.

If the rating label in the rangehood does not show

the symbol , the appliance is built in class I° and it

needs the earth connection.

When performing the electrical connections on the

appliance, please make sure that the current-tap

is provided with earth connection and that voltage

values correspond to those indicated on the label

placed inside the appliance itself.

Before carrying out any cleaning or maintaining

operations, the appliance needs to be switched off.

If the appliance is not provided with a non-separable

When ducting rangehood, options are as follows:

Roof vent - EASYROOF 150T/M

*Kit includes roof flashing

Download installation guide

Eave vent - EASYEAVE 150

Download installation guide

Wall vent - EASYWALL 150

Download installation guide

flexible cable and plug, or with another device

ensuring omnipolar disconnections from the grid,

with an opening distance between the contacts of at

least 3mm, then such disconnecting devices must be

supplied within the fixed installation.

If the fixed appliance is endowed with a supply cord

and a plug, the appliance has to be put in a place

where the plug can be reached easily.

The use of materials which can burst into flames

should be avoided in close proximity of the appliance.

When frying, please pay particular attention to fire

risk due to oil grease. Being highly flammable, fried

oil is especially dangerous. Do not use uncovered

electric grills. In order to avoid possible fire risk, all

instructions for grease-filter cleaning and for removing

eventual grease deposits should be strictly followed.

WARNING

600 - 700mm (induction)

650 - 750mm (gas)

600 - 700mm (induction)

650 - 750mm (gas)

(Fig. 1)

(Fig. 2a)

(Fig. 2b)

(Fig. 2c)

SIDE VIEW FRONT VIEW

To install the appliance please read the following

instructions:

• The appliance must be installed by qualified

technicians, or where possible use a Sirius

recommended installer. See siriusbrand.com. In

order to avoid damage to the electronic parts

of the appliance, please do not use additional

screws.

• Follow the instructions below carefully:

Make a cutout on the bottom of the cabinet

which is suitable to hold the rangehood in

position (fig. 5):

SL926 DL520 - 506 x 265mm

SL926 DL850 - 831 x 265mm

SL926-DL series INSTALLATION -

ONBOARD

Before installing the appliance, make sure that

none of the parts are damaged in any way. In

case of damaged parts, contact your retailer

and do not proceed with installation. Read all

of the following instructions with care before

installing the appliance.

• Use ducting within the min/max specifications

• Limit the number of ducting bends.

• Do not make any changes in ducting diameter

(recommended constant diameter: Ø 150 mm.

Before installing the appliance - in order not to

damage the appliance itself - the metal grease filter

should be removed. These filters could be removed

by pushing the handles towards the back side of the

rangehood and pulling it downwards to unfasten it

from its slot. (Fig.3). When refitting the filters, please

ensure the handles are at the front of the rangehood.

NOTE

Fig.3

Fig.4

(Fig.5)

1. Prepare the power supply - 240 volts.

2. Prepare a hole for the exhaust - 160mm diameter

for single motor.

• Do not use screws to fix the ducting to the

rangehoods as they will prevent the movement of

non-return valves.

• Limit the number of elbows in the ducting, since

each elbow reduces the duct efficiency by 1

metre. (i.e. if you use two 90° elbows, the length

of ducting must not exceed 5 metres.)

• Avoid abrupt direction changes.

• Use 150mm constant diameter ducting for the

whole length for the single motor.

• The use of Sirius ducting will increase the

warranty of the unit to 6 years.

WARNING: Failure to install the screws or fixing

device in accordance with these instructions

may result in electrical hazards.

• Remove the rear grease channel by turning the

screws anti-clockwise (Do not unscrew all the

way, half a turn will be sufficient for the channel to

removed. See Fig 4)

506/831 mm

265 mm

CAUTIONWARNING

The rangehood is quite heavy, so two people

will be needed for installation.

1. To install the appliance, adjust the position of the

adjustable side-springs using the supplied screws

(fig.6), according to the thickness of the board, in

which the appliance will be fixed.

2. Insert the rangehood into the cutout in the

cabinet until the stop click of the side-springs is

heard and the rangehood is supported.

3. Insert the 6 x 25mm screws provided into the

holes inside the rangehood (Fig.7) to fix it to

cabinetry.

Before connecting any ducting to the motor,

make sure the non-return valves - which are on

the air outlet of the motor - can swing open.

External venting

• Connect the flange to the exhaust hole with the

appropriate ducting. Connect the rangehood with

the electrical mains through the supply cord.

Rear vented version

• All the models with one motor can be rear

vented; if the customer wants to use this option,

it is necessary to remove the 18 x 10mm screws

from the motor group support. Then take the

metal support with motor included out (Fig.8).

Turn the motor to have the air outlet on the rear

side (Fig.9) and fix the 10mm screws previously

removed.

(Fig.7)

27mm

4. Insert the grease channel.

5. Insert the grease filter (Shown in Fig.4)

(Fig.8)

(Fig.9)

(Fig.6)

SL926-DL series (Fig.13)

A: Light switch on/off

B: Speed 1/ Motor off - (low/simmer)

C: Speed 2 - (general cooking)

D: Speed 3 - (high powered cooking)

E: Speed 4 - (booster)

F: 10 minute shut-off timer

OPERATION

LINE DRAWING

INTERNAL STAINLESS STEEL FLUE

COVER INSTALLATION

(Fig.13)

(Fig.12)

(Fig.11)

• Fix the supplied bracket to the top of the inside

of the cabinetry. NOTE: The bracket must be

positioned against the rear of the cabinetry with

a 3mm space between the bracket and the wall

and perfectly centered. (Fig. 10)

• Position the upper and lower flue covers onto

the top of the rangehood and telescope upwards

the upper flue cover until it lines up with the top

bracket. (Fig. 11)

• Secure to the bracket on the left and right hand

side into position using the two supplied 8mm

screws (Fig. 12)

(Fig.10)

SL926 - 520 - 850

To remove the rangehood from the cabinet,

remove the fixing screws (fig. 7) using a

screwdriver, and remove the grease filters

(fig.4).

• Push down on the small handle of the springs,

which are inside the rangehood, with the

necessary strength to unhook the hood from the

cabinet.

If the supply cord is damaged, it must be

replaced by the manufacturer or its service

agent or a similarly qualified person in order to

avoid a hazard.

• Accurate maintenance guarantees good

functioning and long-lasting performance.

• Particular care is due to the grease filter panel. It

can be removed by pushing its handle toward the

back side of the rangehood and pulling the filter

downwards so to unfasten it from its slot (Fig.3).

To insert the filter just perform the opposite

operation.

• After 30 hours of operation, the push button

control panel will flash, signaling the filters are due

for cleaning. Press the timer button to reset.

The grease filter needs cleaning by regular

handwashing or in dishwashers every two

months at least, depending on its use.

Filters may require cleaning sooner if

frequent heavy frying is done.

• To clean the appliance itself, water and detergent

are recommended, while abrasive products

should be avoided. For steel appliances

specialized detergents are recommended (please

follow the instructions indicated on the product

itself to obtain the desired results).

MAINTENANCE

WARNING

NOTE

(Fig.14a)

(Fig.14c)

(Fig.14b)

(Fig.14d)

REPLACING THE LED LIGHT ON THE

SL 926-DL

1. Before replacing the LED light, switch off the

rangehood, then - by using appropriate tools -

remove the LED light from its slot. (Fig 14a - b)

2. Take out the LED light from its connector and

replace. (Fig 14c - d)

• To find the correct LED light, please contact Sirius

directly on our toll-free number: 1300 762 216.

• NB: light is easier to remove from the centre of

LED strip. Use a small, flathead screwdriver,

pallette knife or blunt butter knife.

SL926 DL

Working:

6 channel control for rangehood remote.

• When the rangehood is first turned on, hold the

lighting button for 5 seconds.

TECHNICAL DATA

• Alkaline battery powered: 12 V mod. 23 A

• Operating frequency: 433.92 Mhz

• Combinations: 32.768

• Max. consumption: 25 mA

• Operating temperature: -20 ÷ + 55 °C

• Dimensions: 120 x 45 x 15 mm.

OPERATING THE REMOTE

The transmitter is equipped with 5 buttons as

specified below:

: Light ON/OFF.

: Motor ON (speed level 1) / OFF.

: Reduce speed.

: Increase speed.

: 10-minute shut-off timer.

DEFAULT OPERATING CONDITION

The manufacturer supplies the remote control unit

ready to be used with codes preset in the factory.

REMOTE CONTROL OPERATION MODE

Standard configuration:

Standard configuration requires all rangehood remote

control systems to be provided with the same

transmission code. In the event two rangehoods are

installed in the same room or nearby, each system

may affect the operation of the another. Therefore,

the code of one remote control system must be

changed.

Generating a new transmission code:

The system is provided with preset codes. Should

new codes be required, proceed as follows: Press

simultaneously buttons:

for two seconds. When LEDs are on, press buttons:

(within 5 seconds). The LEDs flash 3 times to indicate

the procedure is completed.

WARNING! This operation deletes permanently

the preset codes.

Learning the new transmission code.

Once the transmission code is changed in the

remote control unit, the electronic central unit of the

rangehood must be made to set the new code in the

following way:

Press the red main power-off button of the hood

and then restore power to the electronic control unit.

Within the next 15 seconds, press the Light Button

to synchronise the central unit with the code.

Reset of the Factory configuration:

To restore the Factory configuration, follow the

procedure described below: press simultaneously

buttons:

for 2 seconds. When LEDs light on, press buttons:

(within 5 seconds). LEDs flash 6 times to indicate the

procedure is completed.

WARNING! This operation deletes permanently

the preset codes.

Emergency button:

In the event that the remote control does not work,

use the emergency button to switch the appliance

off. After any necessary repairs have been performed,

reset the emergency button.

WARNING

The battery should be replaced every year to

guarantee the optimal range of the transmitter. To

replace the battery, take the plastic lid off, remove the

battery and replace it with a new one, making sure it

is placed the correct way.

Used batteries should be discarded in special

collection bins.

NOTE: The removal of the battery may cause

the remote frequency to lose transmission with

the rangehood. Follow the procedure on page 8

of the manual to generate the new code if this

occurs.

The below product:

RC001 Remote Controls complies with the

specifications set out in the Directive RED 2014/53/

EU.

WARNING

Any adjustments or modifications which have not

been expressly approved by the holder of the legal

conformity certificate may invalidate the user’s rights

relating to the operation of the device.

The products are fitted with an electronic device

which swicthes off the unit after 4 hours from the

remote or manual buttons being used.

DIMMABLE LIGHT FUNCTION

This function provides for lights dimmability, ranging

from 20% to 100%, by holding down light key on the

remote control or rangehood buttons.

Functions are the following:

- rangehood light off- shortly press the key - light on

a 100%

- light on at 100% - shortly press the key - light off

- light on at 100% - hold down the light button

to reduce brightness.

- releasing the key during reduction, or increase -

light keeps the luminous intensity reached.

- Light on - dimmed - hold down the light button to

increase brightness.

COLOUR TEMPERATURE SETTING (KELVIN)

Make sure that the lights and the fan are off. Holding

down the TIMER key will turn on the light at the

previously set colour temperature.

Press the TIMER key again. As long as the key

is kept pressed, the colour temperature is changed

from warm to cool, just leave the light key to select

the desired colour. Exit the colour temperature

selection function by pressing the ON/OFF key.

‘BI-POWER’ FUNCTION

The new Smart-Switch BI-POWER feature is

designed to offer the user a rangehood with the

option for significant energy saving and noise

reduction, specifically for cooking that does not

require high-powered extraction performances.

Activating the BI-POWER feature increases the

airflow power of the hood for when a more powerful

extraction is required.

To activate the Bi-Power function, select a speed

on the rangehood by pressing one of the buttons,

and then hold that same button for 3 seconds. You

should be able to hear the rangehood motor power

change. To disactivate the function, press and hold

the current speed setting for 3 seconds.

THE SIRIUS APP

DOWNLOAD SIRIUS APP FOR ANDROID

1. Open the Google Play Store App

2. Search or browse for SIRIUS App.

3. Select it.

4. Tap to Install.

5. Follow the onscreen instructions to complete the

transaction and get the content.

You can change what language is displayed when

you visit Google Play on your computer by changing

your Google Accounts settings.

Note: Apps are designed for use with supported

Android and Chromebook devices and can’t be used

on Windows or Mac computers.

DOWNLOAD SIRIUS APP FOR iOS

Notes:

• After requesting an app, you may be asked to

verify your identity by entering your passcode or by

using Touch ID or Face ID.

• The steps below don’t apply to the iPhone 5c,

iPhone 5, iPhone 4s or the iPhone 4.

1. Open the App Store

• To install apps, you must sign in with your Apple ID

or create one.

2. To browse the App Store, tap Apps (at the bot

tom).

3. Tap Search (at the bottom) then enter SIRIUS App.

4. Tap the app.

5. Tap GET then tap INSTALL.

• If you have a compatible iPhone with Face ID

enabled, double-tap the Side button then look at the

screen to authenticate.

6. If prompted, sign in to the iTunes Store to

complete the install

CREATE YOUR ACCOUNT ON SIRIUS APP.

1. From Home App, Tap on Join now.

2. Insert your account data

Tap Agree with General Privacy and tap on Register.

3. If all instructions are done correctly a Popup

message “Registration was successful. Check

your email for the activation link” appears.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sirius Satellite Radio Dunstabzugshaube Handbücher

Sirius Satellite Radio

Sirius Satellite Radio SL906 DL Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUT951 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SILT-21 B Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SM923 520 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU-DD2-L TC Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT962 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT972 EM WIFI Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT105 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SM923 52 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SM927 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUTC919 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUF6 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUM Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio Downdraft S-DD18 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUTC92 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio STL969 Bedienungs- und Wartungshandbuch

Sirius Satellite Radio

Sirius Satellite Radio SIL-EM490X Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SILT-26 Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL926DLTM Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio S-DDH1.1 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU909 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL920 FRESCO Series Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch