Teledyne Lecroy PP021 Series Bedienungsanleitung

PP021-1

PP021-2

User Manual

PP021

Passive Probe

700 Chestnut Ridge Road

Chestnut Ridge, NY, 10977-6499

Tel: (845) 425-2000, Fax: (845) 578 5985

teledynelecroy.com

PP021 Passive Probe Instruction Manual

Users are permitted to duplicate and distribute Teledyne LeCroy documentation

for internal training purposes only. Resale or unauthorized duplication of

Teledyne LeCroy documentation materials is strictly prohibited.

Information contained herein is classified as EAR99 under the U.S. Export

Administration Regulations. Export, reexport or diversion contrary to U.S. law is

prohibited.

Teledyne LeCroy is a registered trademark of Teledyne LeCroy, Inc. Other product

or brand names are trademarks or requested trademarks of their respective

holders. Information in this publication supersedes all earlier versions.

Specifications are subject to change without notice.

933090-00 Rev A

pp021-user-manual.pdf

November, 2020

User Manual

EAR99 technology subject to restrictions on copyrights page. 1

Terms and Symbols

The following symbols appear on the product or in its documentation:

WARNING

High Voltage. Risk of electric shock or burn.

WARNING or

CAUTION

Condition or practice could result in injury or loss

of life, or damage to equipment.

DOUBLE INSULATION

PROTECTIVE (EARTH) TERMINAL

Introduction

Teledyne LeCroy PP021 is a passive high impedance voltage oscilloscope

probe designed and calibrated for use with general purpose oscilloscopes

having an input impedance of 1 MΩ. It can be compensated for use with

instruments having an input capacitance between 14 and 25 pF. It is

compatible with oscilloscopes that automatically detect probe attenuation

and adjust their readout accordingly.

To avoid electric shock, keep fingers behind the probe’s finger

guard during use.

Rated for indoor use only. Do not operate where conductive

pollutants may be present.

PP021 Passive Probe

2 EAR99 technology subject to restrictions on copyrights page.

Specifications

Model Attn.

Input

Impedance B/W

Rise

Time Length

Compensation

Range

R (MΩ) C (pF) (MHz) (ps) (m) (pF)

PP021

10x 10 11 500 700 1.3 14 - 25

Attenuation Ratio.................. 10:1 ±1%

Max. Input Voltage....... Circuits not directly connected to Mains: 500 Vrms,

.........................................1500 V transient overvoltage

.........................................Measurement Category II*: 400 Vrms

To reduce risk of fire or electric shock, do not exceed the voltage or

category ratings of the probe. See voltage derating curve on p.3.

Pollution Degree..................... Pollution Degree 2*

Operating Altitude ................. Up to 3000 meters

Max. Operating Temp......... 0 to 50 °C

Humidity.................................... 5% to 95% RH (10 to 30 °C)

5% to 75% RH (30 to 40 °C)

5% to 50% RH (above 40 °C)

RH not controlled below 10 °C

* As defined in IEC/EN 61010-031. See definitions below.

Definitions:

Measurement Category II (CAT II) refers to measurements performed on circuits directly connected to

utilization points (socket outlets and similar) of the low-voltage mains installation.

Pollution Degree 2 refers to an operation environment where normally only dry non-conductive

pollution occurs. Temporary conductivity caused by condensation should be expected.

User Manual

EAR99 technology subject to restrictions on copyrights page. 3

PP021 Input Impedance Profile

Voltage vs. Frequency Derating Curve

PP021 Passive Probe

4 EAR99 technology subject to restrictions on copyrights page.

EC Declaration of Conformity

The product conforms to the applicable European Union

requirements per Low Voltage Directive (LVD) 2014/35/EU.

Compliance was demonstrated to the following specification as listed in

the Official Journal of the European Communities:

IEC/EN 61010-031:2015 Safety requirements for electrical equipment for

measurement, control and laboratory use – Part 031: Safety requirements for

handheld probe assemblies for electrical measurement and test.

EU RoHS2 Compliance

The probe and accessories conform to the 2011/65/EU RoHS2 Directive,

inclusive of any modifications of said Directive.

Disposal

The probe complies with the applicable European Union

requirements to Directives 2012/19/EU on Waste Electrical and

Electronic Equipment (WEEE).

User Manual

EAR99 technology subject to restrictions on copyrights page. 5

General Safety Information

Observe generally accepted safety procedures in addition to those

listed here to avoid personal injury or damage to equipment. The

overall safety of any system incorporating this accessory is the

responsibility of the assembler of the system.

Connect only to grounded instruments. Use only with compatible Teledyne

LeCroy oscilloscopes that have their BNC input connected to an earth

ground. Do not connect the probe reference lead to any point which is at a

potential other than earth ground.

Connect and disconnect properly. Connect probe to the oscilloscope before

connecting it to the test circuit. Disconnect the probe input and reference

lead from the test circuit before disconnecting from the oscilloscope. Do

not connect/disconnect probes while connected to a voltage source.

Do not overload. Do not apply any potential to the probe leads that exceeds

the maximum rating of the probe. Observe all terminal ratings on the

oscilloscope before connecting. Consult the oscilloscope product manual

for further ratings information.

Always comply with the Voltage vs. Frequency Derating Curve.

Do not remove probe casing. Touching exposed connections may result in

electric shock.

Use indoors only within operational environment listed. Do not use in wet or

explosive atmospheres. Keep product surfaces clean and dry.

Handle with care. Probe tips are extremely sharp and may puncture skin or

cause other bodily injury if not handled properly.

Keep fingers behind the finger guard of probe body and accessories.

PP021 Passive Probe

6 EAR99 technology subject to restrictions on copyrights page.

Do not operate with suspected failures. Before each use, inspect the probe

and accessories for any potential damage such as tears or other defects in

the probe body, cable jacket, accessories, etc. If any part is damaged, cease

operation immediately and sequester the probe from inadvertent use.

Cleaning

•Clean only the exterior of the probe, cables, and accessories. Use a

soft cotton cloth moistened with a mild detergent and water solution.

Do not allow any portion of the probe to be submerged at any time.

•Dry the probe and accessory thoroughly before attempting to make

any voltage measurement.

•Do not subject the probe to solvents or solvent fumes as these can

cause deterioration of the probe body, cables, and accessories.

Service

Refer all repairs to qualified service personnel. Contact Teledyne LeCroy at

the following address to arrange to return the probe for service:

Teledyne LeCroy, Inc.

700 Chestnut Ridge Road

Chestnut Ridge, NY, 10977-6499

Ph: 800-553-2769 or 845-425-2000

Fax: 845-578-5985

contact.cor[email protected]

For the most complete and up-to-date list of sales and service centers by

country, visit teledynelecroy.com/support/contact.

User Manual

EAR99 technology subject to restrictions on copyrights page. 7

Probe Compensation

Proper compensation of the probe is required to assure amplitude accuracy

of the waveform being measured by matching the probe to the

oscilloscope’s input capacitance. Compensation should be adjusted

whenever the probe is connected to or transferred between oscilloscopes.

Low Frequency

1. Apply a 1 kHz square wave to the probe or connect to the

oscilloscope’s calibrator output.

2. Adjust the single LF trimmer located on the PP021 BNC

Compensation Box until you achieve a flat-topped square wave.

High Frequency

1. Apply a 1 MHz square wave to the probe (< 0.7 ns rise-time).

2. Remove the plastic caps from the two, HF trimmers on the PP021

BNC Compensation Box.

3. Adjust HF2 then HF1 until you achieve a flat-topped square wave.

PP021 Passive Probe

8 EAR99 technology subject to restrictions on copyrights page.

Over-compensated, correct, and under-compensated waveforms

Probe Accessories

Probe Tips

Both the rigid probe tip and the spring tip can be screwed on to the probe

body by hand.

Be sure not to overtighten the tips to avoid damaging the threads.

Ground Accessories

The ground lead and the short collar are attached to the probe at the time

of shipping. To replace the ground lead with the swivel lead adapter,

unscrew the short collar from the probe and remove the ground lead.

Replace the short collar to hold the swivel lead adapter in place.

Alternatively, the long collar can be pushed onto the probe body and used in

conjunction with the ground spring, BNC adapter or PCB adapter.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Teledyne Lecroy Messgerät Handbücher

Teledyne Lecroy

Teledyne Lecroy AP033 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveLink Series Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Frontline NFC-F Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP008 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook Frontline X500 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy LabMaster LM 10-25Zi-A Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy MDA810 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveRunner 8000-R Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy M42de Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy USB Advisor T3 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy SierraNet M328 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy RP4030 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy MDA800A Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy 980 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy M21 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PPE6KV-A Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy ADP300 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy ZD200 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook SierraNet M168 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Frontline X240 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy RP2060 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Frontline SD Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVD3000 Series Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy AP031 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung