Teledyne Lecroy PP026-1 Bedienungsanleitung

PP026-1

PP026-2

Operator’s Manual

PP026

Passive Probe

700 Chestnut Ridge Road

Chestnut Ridge, NY, 10977-6499

Tel: (845) 425-2000, Fax: (845) 578 5985

teledynelecroy.com

PP026 Passive Probe Instruction Manual

Unauthorized duplication of Teledyne LeCroy documentation materials other than for internal

sales and distribution purposes is strictly prohibited. However, clients are encouraged to

duplicate and distribute Teledyne LeCroy documentation for internal educational purposes.

Teledyne LeCroy is a registered trademark of Teledyne LeCroy, Inc. Other product or brand

names are trademarks or requested trademarks of their respective holders. Information in this

publication supersedes all earlier versions. Specifications subject to change without notice.

Manufactured under an ISO 9000 Registered Quality Management System.

This electronic product is subject to disposal and recycling regulations

that vary by country and region. Many countries prohibit the disposal of

waste electronic equipment in standard waste receptacles. For more

information about proper disposal and recycling of your Teledyne LeCroy

product, visit teledynelecroy.com/recycle.

925647-00

May, 2015

Operator’s Manual

Terms and Symbols

The following symbols appear on the product or in its documentation:

DANGER

High Voltage

WARNING

Refer to Manual. Condition or practice

could result in injury or loss of life.

DOUBLE INSULATION

PROTECTIVE (EARTH) TERMINAL

Introduction

The Teledyne LeCroy PP026 is a passive high impedance voltage

oscilloscope probe designed and calibrated for use with general purpose

oscilloscopes having an input impedance of 1 MΩ and can be compensated

for use with instruments having an input capacitance between 10 to 20 pF.

It is compatible with oscilloscopes that automatically detect probe

attenuation and adjust their readout accordingly.

PP026 Passive Probe

Specifications

Model Attn.

Input

Imped.

B/W

Rise

Time

Length

Compensation

Range

R (MΩ)

C (pF)

(MHz)

(ps)

(m)

(pF)

PP026

10x

500

700

1.3

10 - 20

Attenuation Ratio.....................10:1 ± 1%

Max. Input Voltage...................Measurement Category I 1: 500 Vrms

1500 V transient overvoltage

(see voltage derating curve on p. 3)

Measurement Category II 2: 400 Vrms

Pollution Degree ......................Pollution Degree 2 3

Operating Temperature ..........0° C to +50° C

Humidity ....................................5% to 95% RH (10° C to 30° C)

5% to 75% RH (30° C to 40° C)

5% to 50% RH (above 40° C)

RH not controlled below 10° C

Operating Altitude ....................3000 meters maximum

To reduce risk of fire or electric shock, do not exceed the

voltage or category ratings of the probe.

Definitions (per EN 61010-031)

1) Measurement Category I (CAT I)refers to measurements performed on circuits not directly

connected to mains.

2) Measurement Category II (CAT II) refers to measurements performed on circuits directly

connected to the low-voltage installation.

3) Pollution Degree 2 refers to operating environment where normally only dry, non-conductive pollution

occurs. Temporary conductivity caused by condensation must be expected.

Operator’s Manual

PP026 Input Impedance Profile

Voltage vs. Frequency Derating Curve

PP026 Passive Probe

EC Declaration of Conformity

The probe is marked with this symbol to show compliance was

demonstrated to the specifications listed in the Official Journal of

the European Communities: Low Voltage Directive 2006/95/EC:

EN 61010-031/A1:2008 Safety requirements for electrical equipment for

measurement, control and laboratory use – Part 031: Safety requirements

for handheld probe assemblies for electrical measurement and test.

EU RoHS Compliance

The probe and its accessories conform to the 2011/65/EU RoHS2 Directive,

as they have been classified as Industrial Monitoring and Control

Equipment (per Article 3, Paragraph 24) and are exempt from RoHS

compliance until 22 July 2017 (per Article 4, Paragraph 3).

General Safety Information

Observe generally accepted safety procedures in addition to those

listed here to avoid personal injury or damage to equipment. The

overall safety of any system incorporating this accessory is the

responsibility of the assembler of the system.

Connect only to grounded instruments. Use only with compatible Teledyne

LeCroy oscilloscopes that have their BNC input connected to an earth

ground. Do not connect the probe reference lead to any point which is at a

potential other than earth ground.

Connect and disconnect properly. Connect probe to the oscilloscope before

connecting it to the test circuit. Disconnect the probe input and reference

lead from the test circuit before disconnecting from the oscilloscope. Do

not connect or disconnect probes while they are connected to a voltage

source.

Operator’s Manual

Do not overload. Do not apply any potential to the probe leads that exceeds

the maximum rating of the probe. Always comply with the Voltage vs.

Frequency Derating Curve.

Observe all terminal ratings. Observe all markings on the oscilloscope

before connecting. Consult the oscilloscope product manual for further

ratings information.

Do not remove probe casing. Touching exposed connections may result in

electric shock.

Use indoors only within operational environment listed. Do not use in wet or

explosive atmospheres. Keep product surfaces clean and dry.

Handle with care. Probe tips are extremely sharp and may puncture skin or

cause other bodily injury if not handled properly.

Keep fingers behind the finger guard of probe body and accessories.

Do not operate with suspected failures. Before each use, inspect the probe

and accessories for any potential damage such as tears or other defects in

the probe body, cable jacket, accessories, etc. If any part is damaged, cease

operation immediately and sequester the probe from inadvertent use.

Cleaning

•Clean only the exterior of the probe, cables, and accessories. Use a

soft cotton cloth moistened with a mild detergent and water solution.

Do not allow any portion of the probe to be submerged at any time.

•Dry the probe and accessory thoroughly before attempting to make

any voltage measurement.

•Do not subject the probe to solvents or solvent fumes as these can

cause deterioration of the probe body, cables, and accessories.

PP026 Passive Probe

Probe Compensation

Proper compensation of the probe is required to assure amplitude accuracy

of the waveform being measured by matching the probe to the

oscilloscope’s input capacitance. Compensation should be adjusted

whenever the probe is connected to or transferred between oscilloscopes.

Low Frequency

1. Apply a 1 kHz square wave to the probe or connect to the

oscilloscope’s calibrator output.

2. Adjust the single LF trimmer located on the PP026 BNC Box until you

achieve a flat-topped square wave (see figure below):

High Frequency

1. Apply a 1 MHz square wave to the probe (< 0.7 ns rise-time).

2. Remove the plastic caps from the two, high-frequency trimmers on

the PP026 BNC Compensation Box.

3. Adjust HF2 then HF1 until you achieve a flat-topped square wave (see

figure below).

Operator’s Manual

Over-compensated, correct, and under-compensated waveforms

Service

Refer all service to qualified personnel.

For the most complete and up-to-date list of sales and service centers by

country, visit teledynelecroy.com/support/contact.

PP026 Passive Probe

Replaceable Parts

Item

Part Number

Description

Quantity

PK6-5MM-101

Rigid Probe Tip (1 installed standard)

PK5-PK6-001

Trimmer Tool

PK6-5MM-102

Sprung Hook

PK5-PK6-002

Color Coding Rings (2 ea. yellow, red, green, blue)

PK6-5MM-103

Ground Lead with Alligator Clip

PK6-5MM-104

Ground Spring

PK6-5MM-105

PCB Adapter

PK6-5MM-106

BNC Adapter 5mm

PK6-5MM-107

Spring Tip

PK6-5MM-108

Probe Tip Cover

PK6-5MM-109

IC Tip Insulators

PK6-5MM-110

Tip Insulator

Standard Accessory Replacement Kit part number is PKIT6-5MM-101.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Teledyne Lecroy Messgerät Handbücher

Teledyne Lecroy

Teledyne Lecroy BPA 600 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy MDA810 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveRunner 8000-R Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy ZS Series Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVFO108 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PCI Express Gen 4x8 OCuLink Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP016 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy 980 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook SierraNet M168 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy DL03-ISO Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy RP4030 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Quantumdata 780E Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy 980 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Summit T3-8 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PPE6KV-A Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Summit T416 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP008 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WavePulser 40iX Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Frontline Sodera LE Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy MDA800A Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook DL05-HCM Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook DL02-HCM Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook CP030B Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HDA125 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung