Teledyne Lecroy USB Advisor T3 Bedienungsanleitung

Introduction

The Teledyne LeCroy USB Advisor T3™ USB 3.0 Protocol Analyzer is a

verification system for USB development and testing. It supports both USB 2.0 and

USB 3.0. It is designed to record USB traffic and graphically present the logical

transactions and events. It connects to a host machine (laptop or desktop PC) via

USB 2.0.

Please see the Readme file on the installation CD for the latest information on

PC requirements and supported operating systems.

The system can monitor traffic between USB 2.0 links using standard high-speed

compliant cables.

If configured for USB 3.0 testing, the system supports monitoring between

SuperSpeed links using USB 3.0 cables.

USB Advisor T3

Quick Start

Components

The Teledyne LeCroy Advisor T3 Analyzer package includes the following items:

• One Teledyne LeCroy USB Advisor T3 Analyzer

• DC Power Adaptor

• USB cables (three)

• Installation CD-ROM, including documentation

• Quick Start Guide

• Carrying Case

Please see the USB Protocol Suite User Manual on the installation CD for

component specifications.

3Description

The front panel has the following indicators and connectors:

Power LED (green if on)

Status LED (blue if system successfully initializes)

(red while booting. If red for more than a minute, hardware failure)

(green while initializing)

Analyzer Port A (downstream) Connects to Device Under Test.

Analyzer Port B (upstream) Connects to Host Under Test.

Analyzer LEDs

Rec - Recording (red if recording enabled)

Trig - Trigger (green if triggering)

2.0 - USB 2.0 (yellow for Low and Full Speed)

(green for Hi Speed)

3.0 - USB 3.0 (green if link is up; flashes green while data transfers;

yellow if polling)

The rear panel has the following indicators and connectors:

USB Type B connector for connection to host machine

Sync/Data: Micro DB-25 (25-pin) external interface connector

(cable sold separately)

Power Connector: 12V, 3A DC

Power Switch (0/1)

Warning: Do not open the enclosure. No operator serviceable parts

are inside. Refer servicing to Teledyne LeCroy customer

care.

4Installing the Software

Note: You must install the software before connecting the Analyzer to the host

machine for the first time.

1. Insert the Installation CD into the CD drive on the host machine.

2. Select Install Software from the Installation CD and follow the on-screen

installation instructions to install the application on the host machine’s hard

disk.

Setting Up the Analyzer

To set up the Analyzer:

1. Connect the AC power cable to the rear of the Analyzer and to a 100-volt to

240-volt, 50-Hz to 60-Hz, 100-W power outlet.

2. Connect the USB port to a USB port on the host machine using the LONG

(6-foot/2-meter) USB 2.0 cable.

3. Insert the Installation CD.

4. Turn on the power switch. At power-on, the Analyzer initializes itself in

approximately ten seconds and performs an exhaustive self-diagnostic that

lasts about five seconds.

5. Click Next after you see the Add New Hardware Wizard window.

6. Follow the Microsoft®Windows®on-screen Plug-and-Play instructions for the

automatic installation of the Analyzer as a USB device on your host machine

(the required USB files are included on the Installation CD)

7. Click Finish when you see the message that says “Windows has finished

installing the software that your new hardware requires” and the driver files

have been installed in your host machine.

6Starting the Application

To start the application, launch the Teledyne LeCroy USB Protocol Suite program

from the Start Menu:

Start > Programs > LeCroy > USB Protocol Suite > USB Protocol Suite.

You can use the software with or without the system connected to the host

machine. Without the Analyzer, the program functions as a trace viewer to view,

analyze, and print trace files.

The first time you open the USB Protocol Suite application, confirm proper

installation by selecting About from the Help menu to view the Software Version,

Firmware Version, BusEngine™ Version, and Unit Serial Number.

Note: When the Advisor T3 is power-cycled, it loses its Bus Engine image.

The image updates automatically when the Application runs.

7First USB Recording

After installing and launching the software, you can test the system by performing

the following steps:

1. Connect a USB cable to each of the two connectors on the Analyzer module,

then connect the other ends to the USB Device Under Test and USB Host

Under Test.

2. Select Recording Options under Setup on the Menu Bar.

3. Select the General tab to display the following dialog box showing factory

default settings such as Snapshot and 16 MB buffer size. For the first

recording, you can leave these settings unchanged. Under

Recording Channels, select 2.0 or 3.0 to record USB 2.0 or USB 3.0 traffic.

4. Click OK to activate the recording options you selected.

5. Turn on the USB devices that are to be tested and cause them to generate

USB traffic.

Part Number: 922852-00 Rev. A 3/13

This document may be printed and reproduced without additional permission, but

all copies should contain this copyright notice.

Trademarks and Servicemarks

Teledyne LeCroy, USB Advisor T3, USB Protocol Suite, CATC Trace, and

BusEngine are trademarks of Teledyne LeCroy Inc.

Microsoft and Windows are registered trademarks of Microsoft Inc.

All other trademarks are property of their respective companies.

Disclaimer

Users are fully responsible for their application of any products. The Software

License and Limited Warranty for the accompanying product are set forth in

information that shipped with the product and are incorporated herein by this

reference. If you are unable to locate the Software License or Limited Warranty,

contact Teledyne LeCroy for a copy.

Changes

Product specifications are subject to change without notice.

Teledyne LeCroy reserves the right to revise the information in this document

without notice or penalty.

Teledyne LeCroy Customer Support

Mail: 3385 Scott Blvd., Santa Clara, CA 95054-3115

Web: teledynelecroy.com/tm/Library/software/PSG

E-mail: psgsupport@teledynelecroy.com

Tel: (800) 909-7112 (USA and Canada)

Tel: (408) 653-1260 (worldwide)

Fax: (408) 727-6622 (worldwide)

6. Click on the Tool Bar. The system starts to record the USB traffic

immediately. After 16 MB of traffic are recorded, the Analyzer uploads the

data and displays the packets in the trace window.

7. To terminate recording before the snapshot automatically completes,

click on the Tool Bar.

When the recording session is finished, the traffic is automatically uploaded

from the Analyzer to the hard drive on your host machine as a file named

data.usb or the name you assigned as the default filename. While the file is

being uploaded, you should see a brown progress bar at the bottom of the

screen. When the bar disappears, it indicates that the data has been

uploaded to disk.

8. To save a current recording for future reference, select Save As under File

on the Menu Bar, OR click on the Tool Bar to display the standard

Save As screen.

Give the recording a unique name and save it to the appropriate directory.

For additional information on the results display, see the

USB Protocol Suite User Manual.

Inhaltsverzeichnis

Andere Teledyne Lecroy Messgerät Handbücher

Teledyne Lecroy

Teledyne Lecroy 980 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook ZS4000 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy RP2060 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy MDA810 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy RP4030 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy BPA Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP006C Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveLink Series Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HDA125 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVFO108 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP026-1 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Frontline SD Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy CP150 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy MDA800A Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVD3000 Series Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP016 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PCI Express 5.0 U.2 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Quantumdata 780E Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP011-2 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Summit T3-8 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP011-1 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVD3102 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WavePulser 40iX Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVFO103 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung