Teledyne Lecroy PCI Express 5.0 U.2 Bedienungsanleitung

PCI Express®5.0 U.2/U.3 Interposer

User Manual and Quick Start Guide

Components

The interposer package includes the following components:

• PCI Express 5.0 U.2/U.3 Interposer

• 3.5 Inch conversion bracket kit

• Support bracket extension and screws

• DC Power Adapter (+12V @ 5A)

• User Manual and Quick Start Guide (this document)

Inspect the received shipping container for any damage. Unpack the container and account for each of the system

components listed on the accompanying packing list. Visually inspect each component for absence of damage. In the

event of damage, notify the shipper and Teledyne LeCroy. Retain all shipping materials for shipper’s inspection.

Introduction

Use this document for quick installation and setup.

Teledyne LeCroy’s PCI Express 5.0 U.2/U.3 Interposer provides a quick and simple means for protocol analysis of Solid

State Drives (SSDs) based on PCI Express (PCIe®) protocols. The U.2/U.3 Interposer Card, used with a Summit

Protocol Analyzer, enables PCIe bus traffic between a host backplane and SSD device to be monitored, captured, and

recorded for protocol analysis. The card is compatible with the Summit T516 and Summit T54 and supports data rates

of 2.5 GT/s, 5.0 GT/s, 8.0 GT/s, 16.0 GT/s and 32 GT/s. The interposer supports side band signals such as PERST#,

WAKE#, CLKREQ# and SMBus (SMBCLK, SMBDAT). The interposer can be used with Single x4 Port or Dual x2 Ports.

It also supports U.2 and U.3 standards. It can be used also with Summit T4 and Summit M5x analyzers using a

conversion cable.

PCI Express 5.0 U.2/U.3 Interposer

Clock Selection

The source for the reference clock used by the analyzer to record PCI Express traffic is configurable according to below table. DIP

switches and tables for clock selection are located on the rear side of the interposer.

SW2: Clock Select SW2: Clock Select

12PortB 34PortA

ON ON REFCLKA ON ON REFCLKA

OFF ON US_CLK OFF ON US_CLK

ON OFF DS_CLK ON OFF DS_CLK

OFF OFF REFCLKB OFF OFF REFCLKB

Note: If using direct cable from Summit T516 refer only to table for Cable A for ports A and B.

Note: All switches in the ON position for SW2 is the factory default.

REFCLKA: Use the reference clock from Port A in the U.2 host connector.

US_CLK: Use the reference clock from the corresponding MMCX connector.

DS_CLK: Use the reference clock from the corresponding MMCX connector.

REFCLKB: Use the reference clock from Port B in the U.2 host connector.

Switch Configurations

SW1:This switch connects the DUT power Indication LED to the bus power.

SW1: DUT Power Status LEDs

ON LED Connected (Default)

OFF LED Disconnected

Note: In some systems with Hot-Plug management the Power Indication LEDs on the

interposer may prevent the host system from turning ON bus power to the device, if

this happens disconnect the LEDs using SW1 to allow proper bus power operation.

Connections

IMPORTANT: If you plan to insert the interposer into a chassis backplane you MUST fit the rails from a donor

carrier to the interposer before use to avoid serious damage to the interposer. Instructions for

modifying a hard drive carrier are in Section 7.

Perform the following steps to connect the Interposer (see the image below):

1. Set the SW2 DIP switch to the desired positions to set the clock selection for Port A and Port B according to the table

above (see Section “3” on page ii).

2. Attach the interposer to a drive carrier (See Section “7” on page vi).

3. Install the U.2 or U.3 device under test (DUT) into the bay on the interposer as shown (will fit only 2.5” drives). 

Screw the drive to the bay to secure it.

4. Install the Interposer into the host system connector.

5. Connect the Summit T516 Analyzer (or other compatible Teledyne LeCroy analyzer) to the interposer using

the appropriate analyzer cable (PE028UCA-X Y-cable or PE027UCA-X straight cable). 

6. Connect the analyzer to a host computer system using the USB port on the front panel of the Summit analyzer.

7. If not already done, install the PCIe Protocol Analysis software on the host machine.

8. Connect 12V DC using the AC adapter supplied with the interposer to the Gen5 U.2/U.3 interposer. Make sure that

the AC adapter is powered on before proceeding to the next step.

9. Power on the analyzer.

10. Launch the PCIe Protocol Analysis application, setup the appropriate recording options and start a recording. 

For more information see the PCI Express Protocol Analysis Summit T5 Gen5 Analyzer User Manual -> 

Recording Options -> Select Interposer Type section.

11. Power on the host machine.

12. Use the PCIe Protocol Analysis application to monitor, record and view PCI Express traffic passing through 

the U.2 Interposer.

Analyzer Y cable:

PE028UCA-X

Summit T516 Analyzer

12V DC from

adapter supplied

External Clock Inputs MMCX

(Optional Connection)

Device Under Test

(DUT)

Lane Activity LEDs

SW2: Clock Selection

SW1: DUT Power Status LEDs

Link Standard

Detection LEDs

Link Width Status LEDs

Attach support

bracket for 3.5

Inch conversion

(optional) and

drive carrier

(required). See

sections 7 and 8

below.

Retimer

Connector

J28:Sideband

Signal Header

U.2 Host Slot

Connecting the PCI Express 5.0 U.2/U.3 Interposer to one Summit T516 Analyzer

Sideband Header Pinout

Table 1: J28 Sideband Header

Header Pin Number Sideband Signal Name

J28-1 WAKE#

J28-2 IFDET#2

J28-3 CLKREQ#

J28-4 HPT0

J28-5 IFDET#

J28-6 HPT1

J28-7 PRSNT#

J28-8 SMCLK

J28-9 ACTIVITY#

J28-10 SMDAT

J28-11 PCIEB_RST#

J28-12 DUALPORTEN#

J28-13 PCIEA_RST#

J28-14 DEV_RESET

J28-15 GND

J28-16 GND

Modification of HDD Carrier for Use with the PCIe 5.0 U.2/U.3 Interposer

Warning: DO NOT OPERATE IN A CHASSIS WITHOUT ADDING CARRIER RAILS OR YOU WILL DAMAGE THE

INTERPOSER.

Teledyne LeCroy's PCI Express 5.0 U.2/U.3 Interposer can be attached to a donor drive carrier. If you plan to insert the

interposer into a Chassis backplane you MUST fit the rails from a donor carrier to the interposer before use, to avoid

serious damage to the interposer. In order to do this, some adjustments need to be made to the drive carrier to allow the

interposer to fit properly. Teledyne LeCroy provides these instructions as a service to users but any modification done

to the drive carrier is done at the user’s risk. Teledyne LeCroy provides no guarantee or warranty with these

modifications. These modifications of the drive carrier are the sole responsibility of the user. This procedure is for this

specific drive. carrier. Other drive carriers may need slightly different steps, but this drive carrier is typical. See the

following figures.

Drive Carrier

Ejection Catch Assembly

Step 1. Remove the Drive Carrier from the Server Backplane

To remove the drive carrier from the server backplane, squeeze the two levers together on the front of the carrier and

while gripping the handle provided on the front of the carrier slowly pull the drive carrier out of the server backplane.

Set the drive carrier on a suitable work surface (workbench with ESD pad or similar surface).

Step 2. Remove the Ejection Catch Assembly from the Drive Carrier

To remove the ejection catch assembly, remove two screws holding the metal housing to the ejector catch assembly on

the front of the drive carrier.

Screws holding Ejection Catch to Drive Carrier

Top

Screw Bottom

Screw

Step 3. Remove the Side Runners and Light Pipes from the Drive Carrier

To remove the side runners and light pipes from the drive carrier, slide the black plastic runners towards the back and

lift away from the retaining lugs. Retain the black plastic runners for reuse.

Step 4. Remove the Corner of the Side Rail After Removal from Drive Carrier

Using a suitable cutting tool (diagonal cutting pliers, etc) remove the corners of the side rails.

Step 5. Remove the EMI Shield Springs

The EMI spring system should be gently pulled away and unclipped from the end of the drive carrier. It will not be reused.

Cut along the corner

of the side rail

Typical set of

diagonal

cutting pliers

(or similar tool)

Step 6. Bend Drive Carrier Ears Out of the Way

The drive carrier is usually a simple folded piece of fairly thin metal, which can be gently bent flat by hand. If there are

metal ears, which held the screws to the ejection catch assembly, they should be gently (by hand) unfolded first before

the end of the drive carrier metal is unfolded.

Step 7. Bend Drive Carrier Metal End Out Flat

Gently (by hand) bend the metal end of the drive carrier out flat.

Step 8. Re-Attach the Plastic Side Rails

After the Side Rail corners have been removed, the side rails can be reattached using the original screws.

Ear bent out

of the way

Step 9. Attach the PCI Express 5.0 U.2/U.3 Interposer to the Drive Carrier

Slide the Interposer into the drive carrier, using the original mounting screws to hold it in place. The Interposer should be aligned with

the same holes the drive carrier would have used. Note: Screw type for use with Drive Carrier: Metric screw, size M3, maximum

length: 8mm.

Step 10. Attach Cabling to the Interposer

Insert the carrier with the Interposer into the desired backplane slot. Plug one end of the interposer cable to the

Interposer and other end into the analyzer. Attach the 12VDC power and optional clock cables.

This completes the assembly of the Interposer into the Drive Carrier.

Andere Handbücher für PCI Express 5.0 U.2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Teledyne Lecroy Messgerät Handbücher

Teledyne Lecroy

Teledyne Lecroy M41h Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy 980 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP006D Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PPE6KV-A Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP011-2 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook DL02-HCM Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook Frontline X500 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Frontline Sodera LE Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy LabMaster LM 10-25Zi-A Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy M42de Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP026-1 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy ZD500 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVFO108 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVD3000 Series Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVFO103 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy DXC100A Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy RP4030 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy SierraNet M328 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy CP150 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Summit T3-8 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook SierraNet M168 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy USB Advisor T3 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveAce Lab 3 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy M21 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung