Tennsco 1420 Bedienungsanleitung

GENERAL SAFETY INFORMATION

Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.

For safety, wear a pair of work gloves when assembling or performing any maintenance on products.

LIMITED WARRANTY

Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply

in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during

shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:

a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:

b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO

EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.

NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the

goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty

and are returned within the warranty period stated above.

PK-1481019

ASSEMBLY INSTRUCTIONS & PARTS MANUAL

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE

Standard Storage Cabinet

Unassembled Models 1420

Tennsco LLC., Dickson, TN 37056-1888 • (866) 446-8686

LOAD CAPACITIES PER SHELF LEVEL

36w x 24d 200 lbs.

UNIT SIZE WEIGHT CAPACITY

EVENLY DISTRIBUTED

ASSEMBLY OF 1420 CABINET

Tools Needed: A free 11/32” nut driver is included with each Tennsco cabinet.

Two people are recommended for assembly. Approximate assembly time: 20-30 minutes.

2. Place the cabinet back (Ref. No. 1) on a protected surface

to prevent scratching the paint. The ange on the bottom of

the back should be facing upward.

1. The reference numbers used throughout this sheet refer to

the illustration on the back cover. This is to help you to

identify the various parts as they are mentioned.

3. Attach the left side (Ref. No. 2) to the back by placing

ange (A) around the back and bolting the back and side

together with four bolts and nuts (Ref. Nos. 17 & 18). Be

sure that the lances on all shelf adjustment strips (B) point in

the same direction.

5. Attach the right side (Ref. No. 3) to the back in the same

manner as you did in step 3, again making sure that the

ange is around the back and that the lances on the

shelf adjustment strips are pointed in the same direction

as those on the back and left side. Push the side panel up

so the studs in the top

go through the

holes in the

top ange of

side and

fasten with

three nuts.

6. Attach the sill (Ref. No. 5) to the sides. Place nuts

loosely on each of the studs and slide the ends of the

sill into the slots on both sides of the unit. Then,

securely tighten the nuts.

4. Attach the top (Ref. No. 7) to the unit by sliding the outer

ange over the back of the unit and the side ange to the

side panel on the unit. The threaded studs should go

through the holes in the

top ange of the

side and fasten

with three nuts.

Attach the back

to the top using

four bolts

and nuts.

All lances point UP on

the back and side.

⁭

Flange faces upward.

⁭

Flange goes

under back.

⁭

7. Place the rear ange of the bottom (Ref. No. 6) into the

bottom lances of the back. The ange with two holes should

face the front, hanging over the sill. Insert bolts through the

bottom and sill with the head facing the front of the unit.

Secure with two nuts.

⁭

Insert shelf into the

bottom lances.

⁭

1. Place the locking handle

(Ref. No. 9) on the right

hand door and fasten with

two #8-32 X 1/4 hex-head

bolts and lock washers,

provided with the handle.

2. Turn the handle to the

open position and

place the locking cam

(Ref. No. 10) over the

square shank of the

door handle. The latch

must be facing downward

as shown. Then place the

locking cotter pin (Ref. No.

12) through the hole of the

square shank.

3. With the handle still in the open position, hook the

locking bars (Ref. No. 8) to the locking cam (see

“A” at left). Once in position, slowly rotate the door

handle to the closed position so the lock bars

prot rude from the holes at the top and bottom

of the door (shown at right, below).

4. Slide the nylon lock bar

guide inserts (Ref. No.

11) over the lock bar

ends and through the

door slots (see “B” at

right). Push down rmly

until the guides snap

into place.

5. Attach the “dummy” handle

(Ref. No. 13) using two

#8-32 X 1/4 hex-head bolts

and lock washers.

Handle/Locking System Installation

9. Insert the shelves

(Ref. No. 4) at the

desired levels.

⁭⁭

10. Attach the left door (Ref. No. 8) to the unit by placing the

door on the hinges, aligning the hinge holes, dropping the

pins into the slots, then placing the at end of a

screwdriver on the hinge pins

(Ref. No. 15) and

tapping them in with

a hammer.

⁭

8. Set the unit upright and tighten all the nuts and bolts

around the entire unit.

⁭

NOTE: In order to

place the shelves, you

must ﬁrst tilt the shelf

slightly to the left or right

before inserting it into the unit.

11. Attach the right door (Ref. No. 9) to the unit in the same

way you attached the left door.

Leveler

Access Holes

12. The cabinet must be level in order for the doors to close

properly. Levelers may be adjusted by placing the nut driver

through the hole in each end of the sill and adjusting the

leveling screw.

⁭

REPLACEMENT PARTS

⁭

Tennsco Nut Driver

(Ref No. 14)

Bottom

(Ref No. 7)

Left Door

(Ref No. 8)

Left Side

(Ref No. 2)

Top

(Ref No. 5)

Shelf

(Ref No. 4)

Right Side

(Ref No. 3)

Cotter Pin

(Ref No. 12)

Locking Bar Guide

Nylon Insert

(Ref No. 11)

Locking Bar Set

(Ref No. 8)

Locking Cam

(Ref No. 10)

Locking Handle

with Keys

(Ref No. 9)

Back Panel

(Ref No. 1)

REF. NO. DESCRIPTION

1 Back Panel 1 978BAS

2 Left Side 1 LS1420

3 Right Side 1 RS1420

4 Shelf 2 302

5 Top 1 292TO

6 Sill 1 944SS

7 Left Door 1 978LD

8 Right Door 1 978RD

9 Bottom 1 292BO

10 Locking Bar Set 1 978LB

11 Locking Handle w/keys & hardware 1 944LH

12 Locking Cam* 1 944LC

13 Locking Bar Guide Insert (Nylon)* 2 944GI

14 Cotter Pin* 1 CTRPN

15 Hinge Pin* 6 944HP

16 Tennsco Nut Driver 1 TOOL-2

17 #8-32 x 3/8” bolts (not shown above) 14 **

18 #8-32 nuts (not shown above) 24 **

*Included in Ref. No. 11, locking handle with keys and hardware (Part No. 944LH). **Available Locally

QTY. PART NO.

⁭

Sill

(Ref No. 6)

NOTE: Additional hardware may be included for replacement purposes.

1442 (18”d Cabinet)

⁭

Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.

However, should your unit contain missing or damaged parts, please contact your purchase location.

⁭

Hinge Pin

(Ref No. 13)

⁭

Right Door

(Ref No. 9)

49B148

Andere Tennsco Inneneinrichtung Handbücher

Tennsco

Tennsco J1878A-N Bedienungsanleitung

Tennsco

Tennsco WBHC-1516-MGY Bedienungsanleitung

Tennsco

Tennsco FB-12 Bedienungsanleitung

Tennsco

Tennsco 7218 Bedienungsanleitung

Tennsco

Tennsco B-3000 Bedienungsanleitung

Tennsco

Tennsco J2478A-N Bedienungsanleitung

Tennsco

Tennsco B-8400 Bedienungsanleitung

Tennsco

Tennsco J2478A-N-W Bedienungsanleitung

Tennsco

Tennsco 3070 Bedienungsanleitung

Tennsco

Tennsco 1470RH Bedienungsanleitung

Tennsco

Tennsco Standard Combination Cabinet CVD7214 Bedienungsanleitung

Tennsco

Tennsco zt7 Series Bedienungsanleitung

Tennsco

Tennsco Z-Line Steel Shelf Unit Bedienungsanleitung

Tennsco

Tennsco 1842 Bedienungsanleitung

Tennsco

Tennsco RGL-1236S Bedienungsanleitung

Tennsco

Tennsco Sliding Door Jumbo Storage Cabinet JSD2478SU Bedienungsanleitung

Tennsco

Tennsco BCD18-72 Bedienungsanleitung

Tennsco

Tennsco RGL-1236S Bedienungsanleitung

Tennsco

Tennsco 1871 Bedienungsanleitung

Tennsco

Tennsco Imperial Shelving Bedienungsanleitung

Tennsco

Tennsco Open Foreman's Desk Bedienungsanleitung

Tennsco

Tennsco LSS-361872 Bedienungsanleitung

Tennsco

Tennsco FS350 Bedienungsanleitung

Tennsco

Tennsco JUMBO Gebrauchsanweisung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung