Tornado Pac-Vac 93016 Handbuch

TORNADO INDUSTRIES, LLC

3101 WICHITA COURT

FORT WORTH, TX 76140

PHONE: 800-VACUUMS

FAX: 817-551-0719

WWW.TORNADOVAC.COM

Operations & Maintenance Manual

For Commercial Use Only

Pac-Vac™ 6 Roam

MODEL NO: 93016

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

Long Term Buyer Protection Limited Warranty

10 Years*

Plastic water tanks and Rotationally-molded bodies

2 Years*

Parts on all Tornado cleaning equipment

1 Year*

Labor on all Tornado cleaning equipment

1 Year*

Warranty on batteries, one year prorated

All battery warranties are handled directly by the battery manufacturer, on a one year prorated basis

Tornado Industries, LLC. (Tornado) warrants to the end/user customer that the Tornado product(s) will

be free from defects in material and workmanship for the duration(s) described below. This limited

warranty DOES NOT cover machines and/or components subject to normal wear and tear, damage

that occurs in shipping, failures resulting from modication, accident, unsuitable operating environ-

ment, misuse, abuse, neglect, or improper maintenance by you. For full details, contact your Autho-

rized Tornado Distributor, Service Center, or the Tornado Technical Service Department. Tornado

sales and service representatives are not authorized to waive or alter the terms of this warranty, or to

increase the obligations of Tornado under the warranty.

Terms subject to change without notice

1. Except all Windshears™ Blowers, Storm, TV2SS, Side and Downdraft, Insulation Blowers, CV 30,

CV 38, CK14/1 PRO, CK 14/2 PRO, SWM 31/9, CK LW13/1, CK LW 13/1 ROAM, CV 38/48 Dual,

PV6, PV10, PV6 ROAM, Wall Mount Vacuum and all chargers are warranted for 1 (one) year for both

parts and labor.

2. All non-wear item parts purchased after warranty expiration are warranted for 90 days.

3. Warranty starts from the date of sale to the consumer or, at Tornado’s discretion, 6 months after

the dealer purchased the unit from Tornado, whichever comes rst.

4. The EB 30 is warranted for a period of 90 days for both parts and labor.

5. The warranty on engines used on propane powered equipment is limited to motor manufacturer’s

warranty.

6. Ride-on Scrubbers are warranted for 24 months, parts, 6 months labor or 1,000 hours, whichever

occurs rst.

Note: Tornado, The Latest Dirt, Floorkeeper,

Carpetkeeper, Carpetrinser, Carpetrinser/Dryer,

Headmaster, Taskforce, PAC-VAC, T-Lite, Glazer,

Windshear, Max-Vac and Trot-Mop are trademarks

of Tornado Industries

Website: www.tornadovac.com

Phone 1-800-VACUUMS

Fax 817-551-0719

Address 3101 Wichita Court

Fort Worth, TX 76140

1-800-VACUUMS 90 Years of Cleaning Innovation A Tacony Company

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

NOTES

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

Your new Tornado unit is a high quality, precision-made product. All parts used in the manufacturing of

this unit have passed rigid quality control standards prior to assembly. Please safeguard the original

receipt / invoice. If you experience any problems with your unit during the warranty period, the original

receipt / invoice will act as proof of purchase. Contact Tornado for any warranty inquiries.

IMPORTANT SAFETY INSTRUCTIONS

READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING THIS UNIT

Read and understand this owner’s manual and all labels on the unit before operating. Safety is a

combination of common sense,staying alert and knowing how your unit works. Use this unit only as

described in this manual. Use only manufacturer’s recommended attachments. To reduce the risk of

personal injury or damage to your unit use only Tornado recommended accessories.

Check the carton for shipping damage. Carefully unpack and inspect your new Tornado vacuum for

shipping damage.

Each unit is tested and thoroughly inspected prior to shipping. If damage is discovered, immediately

notify the transportation company that delivered your machine and request an inspection. As a manu-

facturer, we are unable to act upon any claim for concealed damage; you must originate the claim.

Be sure to keep the carton, packing inserts, packing lists, and carrier’s receipt until the inspector has

veried your claim.

PROTECT THE ENVIRONMENT

Pleasedispose of packagingmaterials in an

environmentallysafe wayaccordingto local

waste disposalregulations.

Alwaysrememberto recycle

Do not operate the vacuum while it is standing on high pile carpet/ It is essential that the exhaust

airow not be restricted

Do not wash or launder the cloth bag as this will destroy the ltration capacity of the fabric.

SAFETY PRECAUTIONS

GENERAL PRECAUTIONS

• You must be trained in the operation of this machine before use. Please read this manual carefully

and obtain operation instructions from your safety director or your authorized Tornado distributor.

• Do not attempt to repair warranted machines. All repairs must be done by a qualied and authorized

repair center. Non warranted repairs will be billed back to the owner of the unit.

• Do not use any replacement parts except those specied in the parts list. Unauthorized parts could

cause the unit to malfunction and will void the warranty.

FAILURE TO COMPLY WITH THE ABOVE WARNING INSTRUCTIONS

WILL VOID THE WARRANTY

Disconnect the battery pack from the appliance before making any adjustments, changing accesso-

ries, or storing appliance. Such preventive safety measures reduce the risk of starting the appliance

accidentally.

Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidental-

ly occurs, ush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from

the battery may cause irritation or burns.

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

IMPORTANT SAFETY INSTRUCTIONS

FOR COMMERCIAL USE

WHEN USING AN ELECTRICAL APPLIANCE, BASIC PRECAUTIONS SHOULD

ALWAYS BE FOLLOWED INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:

•

• To avoid electrical shock, Use indoors only. Do not use outdoors and do not expose to rain.

• Do not allow to be used as a toy. Close attention is necessary when used by or near children.

• Use only as described in this manual. Use only manufacturer’s recommended attachment.

• Keep hair, loose clothing, ngers, and all parts of body away from openings and moving parts.

• Always keep hands feet and loose tting clothing away from moving parts to prevent possible

injuries.

• Do not use machine in areas where ammable and/or explosive vapors or dusts are present.

• Make sure voltage and frequency at the wall receptacle correspond with that indicated on

nameplate before plugging in machine.

• Use extra care when cleaning on stairs.

• Do not pick up anything that is burning or smoking such as cigarettes, matches, or hot ashes.

• Do not use without dust bag and/or lters in place.

SAVE THESE INSTRUCTIONS

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

WARNING!

Battery and Charging Safety:

To reduce the risk of electric shock, re, battery explosion, or injury:

1. Use only Tornado charger X1194 and Tornado battery pack X1200

2. DO NOT expose battery packs to temperatures above 122°F (50°C). Never leave battery packs in

automobiles on hot days, where temperatures can be much higher than the outside temperature.

3. DO NOT use or store vacuum or batteries in wet or moist conditions, or with ammable or combus-

tible materials.

4. DO NOT charge batteries or store battery for extended periods,1 month or more, in temperatures

above 90°F (32°C) or below 40°F (5°C).

5. When charging, make sure that the charger has at least 6 inches of clearance on all sides. Ad-

equate airow is required to cool the charger when in use.

6. Connect charging cord to a properly grounded outlet only. See Grounding Instructions.

7. DO NOT use a damaged cord or plug for charging.

8. DO NOT pull on charger’s cord to unplug. Grasp and pull the plug, not the cord.

9. DO NOT handle the charger’s cord plug with wet hands when inserting into electrical outlet.

10. Keep sparks and ames away from batteries.

11. DO NOT smoke near batteries or charger.

12. DO NOT charge the unit outdoors.

13. DO NOT attempt to repair, service, or modify the battery system or charger. Contact Tornado Cus-

tomer Service with any issues.

14. DO NOT short-circuit the battery or charger terminals with conductive items such as paper clips.

This can deliver high current, resulting in heat and re.

15. DO NOT crush, drop, incinerate or damage the battery pack.

16. DO NOT use a battery pack that has been damaged in any way.

17. DO NOT incinerate the battery even if it is severely damaged or nonworking. The battery can

explode in a re.

To avoid damage to the battery contacts, turn off power switch before reconnecting the battery. Bat-

tery must be fully engaged to insure proper electrical connection.

INSTALLING BATTERY PACK INTO VACUUM

1. Holding battery by the front, carefully slide the

battery into the lower housing until it clicks in

place (Fig. 1).

2. Connector is spring-loaded. Battery will need

to be pushed fully into position.

BATTERY FUEL GAUGE

The battery fuel gauge indicates the approximate

run time remaining on the battery. When the

battery button is pressed, one to four indicators

will light up, indicating the approximate battery

charge remaining as follows:

All 4 lights on: Full Charge

3 lights on: 70% Charge

2 lights on: 45% Charge

1 light on: 25% Charge

1 light on and blinking: Low battery, charge when possible

Fig. 1

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

Wearing the Backpack Vacuum

The backpack is designed to balance the weight of the vacuum on the hips, not the shoulders.

1.Adjust the Vari-Quick height adjuster to your back length.

2. Loosen all of the straps and place the vacuum on your back.

Fig. 2 Fig. 3 Fig. 4 Fig. 5

3. Place the hip belt over your hip and connect the buckle. Your hip bones should be centered be-

tween the top and bottom of the belt. Pull the straps forward to tighten the hip belt. (Fig. 2)

4. Pull down the shoulder straps to tighten the backpack on your shoulders. (Fig. 3) Do not tighten

too tight. The main weight of the vacuum should be on the hip belt. The anchor points of the shoulder

straps should ideally be between the shoulder blades. Adjust the Vari-Quick height adjuster if neces-

sary to properly place the vacuum to your back length.

5. Adjust the sternum strap on a comfortable part of your chest and close the strap. (Fig. 4)

6. Loosen or tighten the stabilizer straps as needed, to t your back. (Fig. 5)

7. Do nal adjustments on the shoulder and stabilizer straps as needed to balance the weight of the

vacuum on the hips.

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

OPERATION INSTRUCTIONS

Please read the following operating instructions carefully. They will help you to get the best

performance from this professional quality vacuum cleaner and to maintain it in optimum condition.

Follow these simple steps for easy and effective operation of the Backpack vacuum.

Open the lid and ensure that the cloth bag is correctly located and the exible ring provides a proper

seal when the lid is closed. For optimum performance, ltration and maximum hygiene, it is advisable

to use a paper vacuum bag in addition to the standard cloth bag.

If a paper vacuum bag is used, simply insert it into the cloth bag, making sure that the cardboard disk

is centered on the exible sealing ring. When you replace the lid, the short nozzle in the center of the

lid will be forced into the central hole of the cardboard disk of the paper vacuum bag thus providing

a tight seal. Make sure the paper vacuum bag is tightly secured over the short nozzle before

vacuuming.

Lock the lid down with the two latches. Always ensure that the cloth vacuum bag is empty and the

paper bag is no more than ½ full before vacuuming. The vacuum hose is tted into the cuff in the lid.

It should not be necessary to remove the hose in normal operation.

1. Place the Backpack vacuum on your back, adjust the shoulder straps until you feel comfortable

and then tighten the waist belt. The Backpack vacuum is designed to ride higher on your back

for maximum comfort.

2. Attach the extension wand to the hose and t the oor tool or any of the other vacuuming

accessories on the wand.

3. Turn the vacuum on. The toggle switch is located on the lower housing.

4. After you nish cleaning, turn off the main power switch.

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

PREPARING BATTERY PACK FOR CHARGING

1. Plug the charger's power cord into the battery (Fig. 6).

2. Plug the charger's power cord into 120V wall outlet (Fig. 7).

3. The indicator light should turn Red and blink while charging and turn Green when fully charged

(Fig. 8). The battery pack may require approximately 2.5 hours to fully charge.

4. Verify the charge level of the battery pack by pressing the power level indicator button on the front

of the pack. (Fig. 9). Four lights (one red and three green) indicate a fully charged battery. Unplug bat-

tery from charger and unplug cord from wall outlet after charging.

*Battery pack may get warm while charging.

Fig. 6 Fig. 7

Fig. 9

Fig. 8

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

TO CHANGE THE FILTER COLLECTION BAGS

• Turn off the main power switch (Fig. 10).

• Remove vacuum hose from top of unit (Fig 11).

• Release the two latches and lift off lid (Fig. 12).

• Separate lid from paper bag insert and dispose of paper bag (Fig. 13)

• Remove cloth lter bag, clean, dust and replace (Fig. 14).

• Insert new paper bag making sure to align lid nozzle with bag hole and replace latches (Fig. 15)

Fig. 10 Fig. 11

Fig. 12 Fig. 13

Fig. 14 Fig. 15

CHANGING EXHAUST FILTER ASSEMBLY

The Pac-Vac vacuum cleaner is equipped with a HEPA lter and an exhaust lter. These lters

capture ne dust particles and protect the motor from dirt. It is important to replace the HEPA lter

approximately every six months. Replace the exhaust lter every fourth time the paper vacuum bags

are changed.

To change or clean the exhaust lter

1. Turn off the main power switch (Fig. 10).

2. Detach the exhaust lter holder from the bottom of the unit (Fig. 16)

3. Remove the exhaust lter from the holder (Fig. 17)

4. DO NOT THROW AWAY THE FILTER HOLDER.

5. Remove the exhaust lter from the plastic holder and shake or brush dirt from the lter.

6. Replace the exhaust lter in the plastic holder and place into vacuum.

Fig. 16 Fig. 17

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

Inhaltsverzeichnis

Andere Tornado Staubsauger Handbücher

Tornado

Tornado CVD 38/2 Bedienungsanleitung

Tornado

Tornado TO 6150 Bedienungsanleitung

Tornado

Tornado 94220 Handbuch

Tornado

Tornado CV 38/1 Bedienungsanleitung

Tornado

Tornado PS Series Handbuch

Tornado

Tornado S15 Handbuch

Tornado

Tornado CK LW 13/1 Roam Bedienungsanleitung

Tornado

Tornado ExSELLerate Marathon 350 Handbuch

Tornado

Tornado 95995 Bedienungsanleitung

Tornado

Tornado 90569 Handbuch

Tornado

Tornado CK 3030 Produkthandbuch

Tornado

Tornado Marathon 350 98132 Handbuch

Tornado

Tornado Nomad 4412 Bedienungsanleitung

Tornado

Tornado TV2 SS Handbuch

Tornado

Tornado TIV2000 Bedienungsanleitung

Tornado

Tornado TV2 Handbuch

Tornado

Tornado 98699 Handbuch

Tornado

Tornado Pac-Vac 6 Roam Handbuch

Tornado

Tornado TO 1078 Bedienungsanleitung

Tornado

Tornado TO 4210 Bedienungsanleitung

Tornado

Tornado CA 6200 Bedienungsanleitung

Tornado

Tornado 95954 Handbuch

Tornado

Tornado ExSELLerate Series Einrichtungshandbuch

Tornado

Tornado B2000 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch